Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Article Citation - WoS: 8Hydrogen Sulfide Determination by Solid Surface Luminescence(Springer Verlag, 1996) Eroğlu, Ahmet Emin; Volkan, Mürvet; Bayramlı, Erdal; Ataman, O. Yavuz; Mark, Harry B.In the analytical system suggested, atmospheric hydrogen sulfide reacts with the surface of a filter paper treated with aqueous cadmium chloride and yields a luminescent species whose intensity can be correlated with the analyte concentration in ambient air. It was shown that the luminescent species are CdS solid particles which were formed in a well defined size. The paper luminescence was also tried on polymeric surfaces; polyethyleneoxide, polyvinyl alcohol, ethylcellulose and carboxymethylcellulose were found to give a similar luminescence signal. The system can be used on the tip of an optical fiber for an irreversible, cumulative type of analytical device for hydrogen sulfide determination. The 3s detection limit for the paper luminescence detection system was 7.8 ppb H2S.Article Citation - WoS: 13Citation - Scopus: 15A Study of Adsorption of Water Vapour on Wool Under Static and Dynamic Conditions(Springer Verlag, 1998) Ülkü, Semra; Balköse, Devrim; Çağa, Tayfun; Özkan, Fehime; Ulutan, SevgiAdsorption of water vapour on wool provides not only textile comfort, but also convenience in transportation due to increase in its bulk density. The adsorption and desorption isotherms of water vapour for wool were determined by both volumetric technique using a Coulter Omnisorp 100CX instrument and gravimetric method employing a Cahn 2000 electronic microbalance. Adsorption isotherm fitting to B.E.T. model and hysteresis on desorption was observed. The average effective diffusion coefficient of water in wool was found to be 8.4 × 10-14 m2 s-1 at 25°C from gravimetric data. The effects of packing height and air velocity on the breakthrough curves were also investigated in the wool packed columns. For pseudo first order model, k values changing between 0.33 × 10-6 -69 × 10-6 s-1 was obtained for 2.2-6.4 cm s-1 air velocity and 0.05-0.20 m packing height ranges.Article Citation - WoS: 23Citation - Scopus: 26Body Waves in Fractured Porous Media Saturated by Two Immiscible Newtonian Fluids(Springer Verlag, 1996) Tuncay, Kağan; Çorapçıoplu, M. YavuzA study of body waves in fractured porous media saturated by two fluids is presented. We show the existence of four compressional and one rotational waves. The first and third compressional waves are analogous to the fast and slow compressional waves in Biot's theory. The second compressional wave arises because of fractures, whereas the fourth compressional wave is associated with the pressure difference between the fluid phases in the porous blocks. The effects of fractures on the phase velocity and attenuation coefficient of body waves are numerically investigated for a fractured sandstone saturated by air and water phases. All compressional waves except the first compressional wave are diffusive-type waves, i.e., highly attenuated and do not exist at low frequencies.Article Citation - WoS: 54Citation - Scopus: 61Wave Propagation in Fractured Porous Media(Springer Verlag, 1996) Tuncay, Kağan; Çorapçıoplu, M. YavuzA theory of wave propagation in fractured porous media is presented based on the double-porosity concept. The macroscopic constitutive relations and mass and momentum balance equations are obtained by volume averaging the microscale balance and constitutive equations and assuming small deformations. In microscale, the grains are assumed to be linearly elastic and the fluids are Newtonian. Momentum transfer terms are expressed in terms of intrinsic and relative permeabilities assuming the validity of Darcy's law in fractured porous media. The macroscopic constitutive relations of elastic porous media saturated by one or two fluids and saturated fractured porous media can be obtained from the constitutive relations developed in the paper. In the simplest case, the final set of governing equations reduce to Biot's equations containing the same parameters as of Biot and WillisArticle Citation - WoS: 11Citation - Scopus: 14Quasi-Static and Dynamic Compression Behaviour of an Fptm Alumina-Reinforced Aluminium Metal Matrix Composite(Springer Verlag, 1998) Güden, Mustafa; Hall, Ian W.An aluminium metal matrix composite reinforced with continuous unidirectional α-alumina fibres has been compression tested at quasi-static and dynamic strain rates. In the transverse direction, the composite showed increasing flow stress (at 5% strain) and maximum stress within the studied strain rates, 10−3−3 × 103 s−1. In the longitudinal direction, the maximum stress of the composite increased similarly with increasing strain rates within the range 10−5−7 × 102 s−1. It is shown that, if brooming of the sample ends can be suppressed, the failure stress of the composite in longitudinal compression increases significantly. Metallographic observations reveal the typical modes of damage initiation in the composite.Article Citation - WoS: 10Electrolysis of Mgcl2 With a Top Inserted Anode and an Mg-Pb Cathode(Springer Verlag, 1994) Güden, Mustafa; Karakaya, İshakHigh energy consumption in the production of magnesium by molten salt electrolysis is mainly due to the recombination of magnesium and chlorine. The large interelectrode distance used, in conventional techniques, to reduce the extent of ‘back reaction’, results in a significant potential drop. A laboratory cell that enables the operation with smaller interelectrode distance and easy separation of electrode products has been used to study electrolytic magnesium production. The cell features a top inserted graphite anode and a Mg-Pb alloy cathode at the bottom. Current efficiency and power consumption were determined at 690° C using a current density of 0.48 A cm−2. Experiments were performed to study the effects of MgCl2 concentration and anode-cathode distance (a.c.d.) on cell operation. Results indicated that an electrolyte containing 20% MgCl2 (equiweight NaCl:KCl and 1 % NaF) with a 3 cm a.c.d. reduced the cell voltage to 3.72 V. This value corresponds to an energy consumption of 11.3 kWh kg−1 including the refining of Mg-Pb alloy produced at the cathode. This cell performance is more energy efficient compared to conventional magnesium cells.