Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article The Effect of Layered Cover Plate Material on the Ballistic Performance of Ceramic Armors: Experimental and Numerical Study(Pergamon-Elsevier Science Ltd, 2026) Cellek, Seven Burcin; Tasdemirci, Alper; Cimen, Gulden; Yildiztekin, Faki Murat; Toksoy, Ahmet Kaan; Guden, MustafaThis study investigates the ballistic performance of silicon carbide (SiC) ceramic armor systems reinforced with single and hybrid metallic cover plates composed of Ti-6Al-4V (Ti64) and copper. Controlled ballistic experiments combined with validated LS-DYNA simulations were conducted to examine how cover-plate material, thickness, and stacking sequence influence penetration resistance, energy dissipation, and failure mechanisms. The experimental results revealed that metallic cover plates significantly enhance protection by improving projectile erosion and extending dwell time. While both Ti64 and copper single layers increased the antipenetration capability (APC) compared with bare SiC, hybrid configurations achieved the highest performance. The optimal design, consisting of a 2 mm Ti64 plate placed in front of a 1 mm copper plate, produced the greatest reduction in penetration depth and the highest APC value. Numerical analyses closely replicated the experimental trends and provided insight into stress-wave interactions, pressure evolution, and damage progression within the ceramic. The findings demonstrate that hybrid Ti64-Cu systems not only improve initial impact resistance but also redistribute energy toward the front layers, reducing stress transmission to the backing and mitigating catastrophic ceramic failure. The combined experimental and numerical results establish a clear design framework for developing lightweight, high-efficiency ceramic armor through tailored hybrid layering strategies.Article Citation - WoS: 6Citation - Scopus: 4Regenerable Nickel Catalysts Strengthened Against H2s Poisoning in Dry Reforming of Methane(Elsevier, 2025) Kesan Celik, Nazli; Yasyerli, Sena; Arbag, Huseyin; Tasdemir, H. Mehmet; Yasyerli, NailIn this study, alumina-supported bimetallic Ni-Cu and trimetallic Ni-Cu-Ce catalysts were synthesized to improve catalysts resistant to coke formation and sulfur poisoning for dry reforming of methane (DRM). The effects of parameters such as feed composition, synthesis method, and H2S concentration using the catalyst with the best activity were also investigated. To determine the physical and chemical properties of the synthesized catalysts, XRD, N2 adsorption-desorption, TGA-DTA, ICP-OES, SEM-EDX, XPS, and DRIFTS analyses were performed. XRD analysis showed that the fresh Ni-Cu catalysts have elemental nickel and gamma- alumina phases in their structures. In addition to these structures, the CeO2 crystal structure was determined for the Ni-Cu-Ce catalyst. Type IV isotherm with H1 hysteresis indicating uniform mesoporous structure was obtained with all the catalysts. The activities of the synthesized catalysts in DRM were performed in the presence of different concentrations of H2S (2 ppm, 50 ppm, and 500 ppm) in a fixed bed reactor at 750 degrees C using a gas chromatography-equipped system. The alumina-supported 8Ni-3Cu-8Ce catalyst prepared by the impregnation method exhibited a higher and more stable activity comparing the bimetallic Ni-Cu catalyst in the presence of H2S. Adding copper and cerium to the nickel catalyst has a curative effect on resistance to coke formation and sulfur poisoning. Excess CO2 in the feed stream increased the H2S poisoning resistance of the catalyst. To analyze the reactor exit stream in catalytic activity using different feed stream compositions such as H2S+He, H2S+CO2+He, and H2S+CO2+CH4+He, FTIR with a gas cell was used. The formation of carbonyl sulfide (COS) and H2O, which occurs due to the possible reaction between CO2 and H2S, was observed. Regeneration studies showed that the catalyst could undergo regeneration with a low oxygen concentration (0.3 % O2 in He). 8Ni-3Cu-8Ce@SGA, which gave 71 % CH4 conversion in the first minute of the reaction test in the presence of 50 ppm H2S, was regenerated after completely losing its activity at the end of 5 h. 66 % CH4 conversion was achieved when tested again in the absence of H2S (CH4/CO2/Ar:1/1/1). The 8Ni-3Cu-8Ce@SGA catalyst was deemed worthy of investigation for industrial applications.Article Citation - WoS: 6Citation - Scopus: 6Inverse Effects of Lanthanide Co-Doping on the Photocatalytic Hydrogen Production and Dye Degradation Activities of Cu Doped Sol-Gel Tio<sub>2</Sub>(Elsevier, 2023) Yurtsever, Husnu Arda; Erzin, Kubilay; Ciftcioglu, Muhsin; Yurtsever, Hüsnü Arda; Erzin, Kubilay; Çiftçioğlu, MuhsinCopper doped and lanthanide-copper co-doped titania powders were prepared by sol-gel technique and the effects of co-doping on the photocatalytic reduction and oxidation activities of titania were investigated in this work. Characterization studies indicated that a reduced structure was formed due to the presence of Ti3+ species in copper doped titania powder and a more stable structure was formed when lanthanides were used as co-dopants. Copper doped powder had a significantly higher activity in photocatalytic hydrogen production (1037 mu mol/g/h) than the co-doped powders (similar to 400 mu mol/g/h). The oxidation activities of co-doped powders however were determined to be about 2 times higher than that of the copper doped powder. The decrease in the reduction activity was attributed to the decrease in the number of Ti3+ sites, whereas the increase in oxidation activity was probably a result of the increase in the surface area and dye adsorption due to lanthanide co-doping.