Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Microstructure-Based Prediction of Mechanical Properties of Austempered Ductile Iron Using Multiple Linear Regression Analysis(Springer int Publ Ag, 2025) Yalcin, M. Alp; Davut, KemalMultiple linear regression analysis (MLRA) was used to predict the mechanical properties of austempered ductile iron (ADI) including yield and tensile strength, uniform elongation, hardening exponent, as well as fracture energy by building a model that uses characteristic features of microstructural constituents as input parameters. The complex multi-scale microstructure of ADI, which is composed of spherical graphite particles over 10 mu m diameter; and an ausferritic matrix with sub-micron sized features, makes it ideal for prediction of mechanical properties. For that purpose, low alloyed ductile iron samples austempered between 300 and 400 degrees C for 45-180 min were tensile tested, and also multi-scale microstructural characterization were carried out using optical microscope, SEM, and EBSD technique. Moreover, a sensitivity analysis was performed to determine which microstructural parameter(s) each mechanical property is most sensitive to. The results show that tensile and yield strength are most sensitive to size and morphology of matrix phases. Moreover, the size and aspect ratio of acicular ferrite correlate well with those of high-carbon austenite; since both form during transformation of parent austenite into ausferrite during austempering treatment. Equiaxed parent austenite grains transform into ausferrite with acicular morphology during the austempering treatment; and presence of equiaxed austenite grains in the austempered samples indicates untransformed regions during austempering treatment. Ductility was found to be more sensitive to nodularity of graphite particles, and this sensitivity was attributed to the size difference between graphite particles and grain size of matrix phases.Article Citation - WoS: 8Citation - Scopus: 8A Review of the Experimental and Numerical Studies on the Compression Behavior of the Additively Produced Metallic Lattice Structures at High and Low Strain Rates(KeAi Communications Co., 2025) Bin Riaz, Muhammad Arslan; Guden, MustafaRecent advances in additive manufacturing have enabled the construction of metallic lattice structures with tailored mechanical and functional properties. One potential application of metallic lattice structures is in the impact load mitigation where an external kinetic energy is absorbed by the deformation/ crushing of lattice cells. This has motivated a growing number of experimental and numerical studies, recently, on the crushing behavior of additively produced lattice structures. The present study overviews the dynamic and quasi-static crushing behavior of additively produced Ti64, 316L, and AlSiMg alloy lattice structures. The first part of the study summarizes the main features of two most commonly used additive processing techniques for lattice structures, namely selective-laser-melt (SLM) and electrobeam-melt (EBM), along with a description of commonly observed process induced defects. In the second part, the deformation and strain rate sensitivities of the selected alloy lattices are outlined together with the most widely used dynamic test methods, followed by a part on the observed microstructures of the SLM and EBM-processed Ti64, 316L and AlSiMg alloys. Finally, the experimental and numerical studies on the quasi-static and dynamic compression behavior of the additively processed Ti6 4, 316L, and AlSiMg alloy lattices are reviewed. The results of the experimental and numerical studies of the dynamic properties of various types of lattices, including graded, non-uniform strut size, hollow, non-uniform cell size, and bio-inspired, were tabulated together with the used dynamic testing methods. The dynamic tests have been noted to be mostly conducted in compression Split Hopkinson Pressure Bar (SHPB) or Taylor-and direct-impact tests using the SHPB set-up, in all of which relatively small-size test specimens were tested. The test specimen size effect on the compression behavior of the lattices was further emphasized. It has also been shown that the lattices of Ti6 4 and AlSiMg alloys are relatively brittle as compared with the lattices of 316L alloy. Finally, the challenges associated with modelling lattice structures were explained and the micro tension tests and multi-scale modeling techniques combining microstructural characteristics with macroscopic lattice dynamics were recommended to improve the accuracy of the numerical simulations of the dynamic compression deformations of metallic lattice structures. (c) 2025 China Ordnance Society. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).Article Citation - WoS: 11Citation - Scopus: 11A Comprehensive Characterization of the Effect of Spatter Powder on In939 Parts Fabricated by Laser Powder Bed Fusion(ELSEVIER SCI LTD, 2023) Dogu, Merve Nur; Mussatto, Andre; Yalçın, Mustafa Alp; Özer, Seren; Davut, Kemal; Obeidi, Muhannad Ahmed; Kumar, AjayThis study is focused on a comprehensive characterization of virgin and spatter IN939 powders and the effects of a certain amount of spatter powder on the part quality of IN939 fabricated by the L-PBF process. A brown tint coloration formed Al2O3 oxide, pores, a 124.4% increase in the average particle size, a 10.2% decrease in the powder circularity, and a 7.5% decrease in the powder aspect ratio were observed in the spatter powder. Additionally, higher average grain size and lower nanohardness were obtained for the spatter powder. In order to understand the effect of a certain amount of spatter powder on the part quality, 10 wt% spatter powder was mixed with the virgin powder. This addition was found to decrease the flowability of the powder. Moreover, this addition decreased relative density by around 0.3% and increased surface roughness by around 80.8% in the fabricated samples (termed as V and SV). On the other hand, there was no considerable microstructural, texture, microhardness, and nanohardness difference between V and SV samples, although the spatter powder addition caused a 30.2% increase in the average grain size of SV. The overall texture for both V and SV samples exhibit (00 1)//BD.