Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Book Part Calcium Soap Lubricants(CRC Press, 2015) İzer, Alaz; Kahyaoğlu, Tuğçe Nefise; Balköse, DevrimThe reparation and characterization of calcium stearate (CaSt2) and a lubricant by using calcium stearate were aimed at in this study. Calcium stearate powder was prepared from sodium stearate and calcium chloride by precipitation from aqueous solutions. CaSt2 and the Light Neutral Base oil were mixed together to obtain lubricating oil. It was found that CaSt2 had a melting temperature of 142.8 °C and in base oil it had a lower melting point, above 128 °C. It was dispersed as lamellar micelles as the optical micrographs had shown. From rate of settling the size of dispersed particles were found to be 1.88 µm and 0.11 µm for lubricants having 1% and 2% CaSt2, respectively. The friction coefficient and wear scar diameter of base oil 0.099 and 1402 nm were reduced to 0.0730 and 627.61 nm respectively for the lubricant having 1% CaSt2. Lower wear scar diameter (540 nm) was obtained for lubricant with 2% CaSt2. CaSt2 improved the lubricating property of the base oil but did not improve its oxidative and thermal stability. © 2015 by Apple Academic Press, Inc.Book Part Calcium Soap Lubricants(Apple Academic Press, 2015) İzer, Alaz; Kahyaoğlu, Tuğçe Nefise; Balköse, DevrimThe reparation and characterization of calcium stearate (CaSt2) and a lubricant by using calcium stearate were aimed at in this study. Calcium stearate powder was prepared from sodium stearate and calcium chloride by precipitation from aqueous solutions. CaSt2 and the Light Neutral Base oil were mixed together to obtain lubricating oil. It was found that CaSt2 had a melting temperature of 142.8 °C and in base oil it had a lower melting point, above 128 °C. It was dispersed as lamellar micelles as the optical micrographs had shown. From rate of settling the size of dispersed particles were found to be 1.88 ?m and 0.11 ?m for lubricants having 1% and 2% CaSt2, respectively. The friction coefficient and wear scar diameter of base oil 0.099 and 1402 nm were reduced to 0.0730 and 627.61 nm respectively for the lubricant having 1% CaSt2. Lower wear scar diameter (540 nm) was obtained for lubricant with 2% CaSt2. CaSt2 improved the lubricating property of the base oil but did not improve its oxidative and thermal stability. © 2015 by Apple Academic Press, Inc.Article Citation - WoS: 15Citation - Scopus: 17Preparation of Particulate/Polymeric Sol-Gel Derived Microporous Silica Membranes and Determination of Their Gas Permeation Properties(Elsevier Ltd., 2010) Topuz, Berna; Çiftçioğlu, MuhsinMonodisperse silica sols with well-defined spherical particles ranging in size from 5 to 310 nm were prepared through Stober process. Both particulate and polymeric sol-gel routes were employed for the preparation of stable silica sols. The use of polymeric species in combination with particulate silica spheres may allow the design of predefined membrane pore structures with high thermal stability by cubic/random/close packing of monodisperse spherical particles incorporated into the polymeric network. The size and volume content of spheres were varied in order to modify the consolidation behaviour of 2-structural silica membranes which would enhance the thermal stability. The low shrinkage level for sphere loaded 2-structural systems compared to the pure polymeric counterparts might be explained by the decrease in the structural free energy of the polymeric/particulate 2-structural system. The thermal stability of the microporous membranes may thus be improved by incorporating particulates into the polymeric network through the formation of a lower extent of thermally induced microcrack formation. The N2 permeation through 90 nm silica sphere added silica membranes remained constant when they were heat treated in the 250-400 °C range indicating the stability of the pore network. © 2009 Elsevier B.V. All rights reserved.Article Citation - WoS: 62Citation - Scopus: 67Thermal Stability of Carbonic Anhydrase Immobilized Within Polyurethane Foam(John Wiley and Sons Inc., 2010) Kanbar, Bora; Özdemir, EkremThermal stability of carbonic anhydrase (CA) immobilized within polyurethane (PU) foam was investigated. The catalytic activity of the enzyme was estimated by using p-nitrophenyl acetate (p-NPA) as the substrate in tris buffer containing 10% acetonitrile. The immobilized CA was stable during the repeatable washings and stability tests over 45 days stored in tris buffer at ambient conditions indicating that the CA was covalently attached to the polyurethane (PU) foam by crosslinking. The immobilized CA was found to be 98% stable below 50°C, whereas a drastic decrease was seen at temperatures between 50 and 60°C. The optimum temperature for the immobilized CA was found to be 45°C and it lost its activity completely at 60°C. Thermal deactivation energies for the free and immobilized CA were estimated to be 29 and 86 kcal/mol, respectively. The association of unfolded CA with the polymeric backbone chains of the PU foam was also addressed. It was concluded that the immobilized CA was highly stable at temperatures less than 50°C and could be used in biomimetic CO sequestration processes. © 2010 American Institute of Chemical EngineersArticle Citation - WoS: 36Citation - Scopus: 42Sol-Gel Derived Mesoporous and Microporous Alumina Membranes(Springer Verlag, 2010) Topuz, Berna; Çiftçioğlu, MuhsinStable polymeric and colloidal boehmite sols were prepared by sol-gel process through controlled hydrolysis/condensation reactions. The particle sizes of the colloidal sols were in the 12-25 nm range depending on the process parameters and about 2 nm for polymeric sols. The presence of a significant increase in the microporosity content of the heat treated polymeric membranes relative to the mesoporous colloidal membranes might make the design of thermally stable microporous alumina membranes with controlled pore structures possible. The phase structure evolution in the 600-800 °C range had shown that the crystallization of the gamma alumina in the amorphous matrix starts at about 800 °C. This indicated that the pore structure stability may be enhanced through processing up to this relatively high temperature in polymeric alumina derived unsupported membranes. The permeance values of the two and three layered colloidal alumina membranes were observed to be independent of pressure which implies that the dominant gas transport mechanism is Knudsen diffusion in these structures. This was also supported by the 2.8 nm BJH pore sizes of the colloidal membranes. The Knudsen diffusion equation derived permeances of the polymeric alumina membranes with thicknesses of about 300 nm were determined to be very close to the experimentally determined permeance values. © 2010 Springer Science+Business Media, LLC.Article Citation - WoS: 11Citation - Scopus: 16Partial Purification of Hen Egg White Lysozyme by Ethanol Precipitation Method and Determination of the Thermal Stability of Its Lyophilized Form(Türkiye Klinikleri Journal of Medical Sciences, 2007) Gemili, Seyhun; Umdu, Emin Selahattin; Yaprak, Nilgün; Üstok, Fatma Işık; Yener, Fatih Yalçın Güneş; Mecitoğlu Güçbilmez, Çiğdem; Altınkaya, Sacide; Yemenicioğlu, AhmetLysozyme was partially purified from hen egg white by precipitation of non-lysozyme protein impurities during incubation in the prence of ethanol. The thermal stability of the obtained partially purified enzyme was also characterized. The incubation of diluted egg white for 2-8 h in the presence of 20% ethanol was not very effective for the partial purification of lysozyme by precipitation of major egg white proteins; however, 4- to 6-h or 6-h to 8-h incubation of diluted egg white in the presence of 30% and 40% ethanol could be employed more effectively for partial purification of lysozyme. Without applying the incubation period, the highest specific activity was obtained by the treatment of egg white with 40% ethanol. Thus, ethanol at this concentration could be used for a continuous process of partial purification. For batch lysozyme purification, on the other hand, incubation in the presence of 30% ethanol was more appropriate. The activities and protein contents of dialyzed and lyophilized enzymes obtained by 6 h-incubation in the presence of 20%, 30%. and 40% ethanol precipitations were 1878, 6669, and 6115 U/mg powder, and 0.98, 0.90, and 0.93 mg protein per mg powder, respectively. The ranges of thermal inactivation parameters, such as D (D80°C = 29.2-59 min, D90°c = 8.8-21 min) and z (Z80-90°c = 17.4-22.3 °C) values of the enzyme, clearly indicated the moderate and variable heat stability of lyophilized lysozymes obtained from different batches of egg white.