Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
125 results
Search Results
Article Citation - WoS: 38Citation - Scopus: 43Quantitative Evaluation of the Damage To Rc Buildings Caused by the 2023 Southeast Turkey Earthquake Sequence(SAGE Publications, 2024) Pujol, Santiago; Bedirhanoğlu, İdris; Dönmez, Cemalettin; Dowgala, Jeffrey D.; Eryılmaz Yıldırım, Meltem; Klaboe, Kari; Köroğlu, Fahri Baran; Lequesne, Rémy D.; Öztürk, Baki; Pledger, Liam; Sönmez, EgemenData from 15 earthquakes that occurred in 12 different countries are presented showing that, without better drift control, structures built with building codes allowing large seismic drifts are likely to keep leaving a wide wake of damage ranging from cracked partitions to building overturning. Following the earthquake sequence affecting southeast Turkey in 2023, a team led by Committee 133 of the American Concrete Institute surveyed nearly 250 reinforced concrete buildings in the area extending from Antakya to Malatya. Buildings ranging from 2 to 16 stories were surveyed to assess their damage and evaluate the robustness of their structures in relation to overall stiffness, as measured by the relative cross-sectional areas of structural walls and columns. The majority of the buildings were estimated to have been built in the past 10 years. Yet, the structures surveyed were observed to have amounts of structural walls and columns comparable with amounts reported after the Erzincan (1992), Duzce (1999), and Bingol (2003) Earthquakes in Turkey. These amounts are, on average, much smaller than the wall and column amounts used in Chile and Japan. Because of that lack of robustness and given the intensities of the motions reported from Antakya to Malatya (with 10 stations with peak ground velocity (PGV) of 100 cm/s or more), it is concluded that structures in this region experienced large drifts. Excessive drift (1) exposed a myriad of construction and detailing problems leading to severe structural damage and collapse, (2) induced overturning caused by p-delta for some buildings, and (3) caused widespread damage to brittle masonry partitions. The main lesson is simple: ductility is necessary but not sufficient. It is urgent that seismic drift limits are tightened in high-seismicity regions worldwide. © The Author(s) 2024.Article Modeling Plasticity and Damage in Fiber Reinforced Composites by a Crystal Plasticity Based Approach(Elsevier, 2023) Dizman, E. Aybars; Özdemir, IzzetIn very thin ply laminates, delamination failure initiation occurs at much higher stress levels as compared to conventional ply laminates. This results in significant plastic deformation in the matrix accompanied by large fiber rotations. A closer look reveals that microstructure of fiber reinforced composites at large strains do not rotate with the plastic spin induced by the total deformation gradient and therefore inelasticity of such materials requires dedicated constitutive models. This paper focuses on inelastic response of such composites by using a recently proposed crystal plasticity based modeling framework and extents it by a non-local continuum damage mechanics formulation. As opposed to existing works related to composites, adapted crystal plasticity model is formulated and implemented in an implicit manner. To address the initiation and evolution of damage observed at large strains, localizing implicit gradient damage (LIGD) framework is used to degrade the slip resistance and hardening mechanisms on longitudinal and transverse slip systems by means of two separate damage variables. A user element (UEL) subroutine encapsulating all the components of the model is developed and integrated within the commercial finite element solver Abaqus. Capabilities of the model are assessed at material point, ply, and component levels by comparisons with analytical solutions and selected experimental results from the literature.Review Citation - WoS: 42Citation - Scopus: 49Utilization of Waste Materials in the Stabilization of Expansive Pavement Subgrade: an Extensive Review(Elsevier, 2023) Tanyıldızı, Muhammed; Uz, Volkan Emre; Gökalp, İslamExpansive soils, also known as swell-shrink soils, are one of the most problematic soils in highway construction and exhibit significant volume changes by swelling and shrinking while wet and dry, respectively. These changes in soil cause cracks, heaves, differential settlements, and damages to the overlying pavements leading to high maintenance costs. The annual average maintenance cost of structures built on expansive soils ranges from $9 to $15 billion, with 50% of the expenses associated with highways and streets. Chemical stabilization techniques such as cement and lime stabilization are one of the most efficient ways to treat expansive soils. However, there is a need to develop environmentally friendly approaches to stabilize expansive soils due to worldwide growing interest in sustainable developments and concerns about greenhouse gas emissions and climate change. In this context, using waste materials in soil stabilization has been considered an important issue for sustainability concerns. The aim of the current study is to review the relevant studies performed to improve the geotechnical and engineering properties of expansive subgrade soils of pavements by using waste materials arising from industrial, agricultural, and other activities in the last decade. In the organization of this study, characteristics of expansive soils including plasticity, compaction, strength & stiffness, microstructural characteristics, shrink-swell properties, and durability were focused to point out the effect of the waste materials. The overall results obtained throughout the scope of the current study indicated that the use of waste materials in soil stabilization improves the engineering properties of expansive soils, significantly. This paper also provides key information and creates awareness for researchers and sector representatives about sustainable soil stabilization.Article Citation - WoS: 9Citation - Scopus: 8Effect of Drainage Conditions on Cpt Resistance of Silty Sand: Physical Model and Field Tests(Springer, 2023) Ecemis, Nurhan; Arık, Mustafa Sezer; Taneri, HazalThe influence of drainage conditions on cone penetration test (CPT) resistance and the excess pore pressure during cone penetration in sand and silty sand are examined using field and physical model tests. Drainage can generally occur in saturated clean sand and silty sand under certain conditions. This work aims to understand and explain the effect of sand and silty sand drainage conditions on CPT resistance and pore pressure through the coefficient of consolidation (c h) and penetration rate (v). The physical model test results indicate the significant effect of excess pore pressures and their dissipation rates, depending on the coefficient of consolidation (silt content) and the penetration rate on cone resistance. For the same relative density, normalized CPT resistance decreases as there is a reduction in c h (or an increase in silt content) or an increase in penetration rate. The difference in CPT resistance in silty sand is attributed to drainage conditions. Finally, the results revealed in this study and the field test data reported in the literature were combined to develop an equation for the effect of drainage conditions on excess pore water pressure and CPT resistance. © 2023, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.Article Citation - WoS: 16Citation - Scopus: 19Comparative Analysis of Estimation of Slope-Length Gradient (ls) Factor for Entire Afghanistan(Taylor & Francis, 2023) Ansari, Ahmad; Tayfur, GökmenSlope length gradient (LS) is one of the crucial factors in the Universal Soil Loss Equations (USLE, RUSLE). This study aimed at estimating the slope-length and slope-steepness (LS) factor for the entire watersheds of Afghanistan by using three different methods, namely; (1) LS-TOOLMFD (Method 1); (2) The Method of Equations (Method 2); and (3) The approach of Moore and Burch (Method 3). The first method uses the digital elevation model (DEM) in the ASCII format, and the other two methods use the DEM in the spatial domain. The results show that the LS-factor of the study area ranges from 0.01 to 44.31, with a mean of 5.24 and standard deviation of 6.95, according to Method 1; 0.03 to 163.49, with a mean of 9.6 and standard deviation of 13.58, according to Method 2; and 0 to 3985, with a mean of 7.16 and standard deviation of 29.7, according to Method 3. The study reveals that Methods 1 and 2 are more appropriate than Method 3 because Method 3 yields high LS-factor values close to or at streamlines located near mountainous regions. The highest LS values are found to be in the northeast, north, and central regions of Afghanistan, which is consistent with the high mountains and deep valley geomorphology, indicating that these regions are particularly vulnerable to soil erosion by rainfall-runoff processes. The sediment delivery ratio (SDR) for the Upper-Helmand River Basin (Upper-HRB) is also estimated by the RUSLE, employing the LS factors produced by the three methods. The results revealed that the average annual soil loss is found to be, respectively, 9.3, 18.2, and 11.1 (ton/ha/year) by using the three methods, corresponding to SDR of 23.5%, 12.1%, and 19.9%.Letter Reply To the Discussion on “the Modified Vlasov Model on a Nonhomogeneous and Nonlinear Soil Layer”(Elsevier, 2023) İşbuğa, Volkan; Çerezci, Mehmet; Aşık, A. ZülfüThe discussion suggests that the paper has left out four references (Haldar and Basu, 2013; Haldar and Basu, 2016; Elhuni and Basu, 2019; Elhuni and Basu, 2021), and the research work in the paper is not new. The authors would like to state that the literature review in the paper was kept as vast as and to stay as close as possible to the model given in the paper, which is a gross model. The study aimed to offer a method using a previously developed formulation for accounting for soil nonlinearity (Vallabhan and Das, 1988,1991a,1991b). The primary concentration in the literature was given to the most relevant works on the modified Vlasov model that employs the same concept for the solution method and algorithm, which lays the foundation of the paper (Vallabhan and Das 1988,1991a,1991b; Asik, 1999; Asik and Vallabhan,2001). On the other hand, as clearly indicated in the study, the literature in the field is extensive, including the works suggested by the discussion. Despite the author’s efforts, it was not possible to review or/ and mention all the works previously conducted to solve the problem with different approaches. In this respect, the previous studies by Haldar and Basu (2013) and Elhuni and Basu (2019) mentioned in the discussion are not directly related to the problem considered in the paper. Haldar and Basu (2016) proposed a framework incorporating the finite difference and the finite element methods.Article Citation - WoS: 11Citation - Scopus: 12An Improved Passive Tuned Mass Damper Assisted by Dual Stiffness(Elsevier, 2023) Roozbahan, Mostafa; Turan, GürsoyA tuned mass damper (TMD) is one of the oldest and most commonly used passive control devices attached to structures to absorb lateral loads of energy from main systems. In the last decades, several novel tuned mass dampers have been designed to increase the performance of TMDs in decreasing the structural responses during excitation vibrations. Moreover, several formulations and numerical optimization methods have been developed to optimize the TMDs parameters. This paper proposes a novel passive tuned mass damper with dual stiffness (DSTMD). The DSTMD includes mass, primary and secondary springs, dashpot, and motion limiting chamber. The performance of DSTMDs depends on their properties such as mass, primary and secondary stiffness, damping coefficient, and the length of the motion limiting chamber. Thus, a metaheuristic optimization algorithm, called the Mouth Brooding Fish algorithm, was used to optimize the DSTMDs parameters. The effectiveness of the optimum DSTMD on two different linear ten-story structures under several earthquakes has been studied and compared with the effectiveness of classical optimum TMDs. According to the study, optimum DSTMDs generally show better effects for certain excitations, and as an average performance, they are superior compared to the classical optimum TMDs in reducing maximum displacement of the buildings. At last, structural yielding is considered, and the performance analysis on this structure shows that the DSTMD has a superior effect in reducing the maximum displacement and is among the best methods for the calculated absolute yielding amount.Article Citation - WoS: 13Citation - Scopus: 14Boron Removal From Geothermal Brine Using Hybrid Reverse Osmosis/Microbial Desalination Cell System(Elsevier, 2023) Jarma, Yakubu A.; Kabay, Nalan; Baba, Alper; Ökten, Hatice Eser; Gören, Ayşegül YağmurAgriculture sector leads worldwide as the most water consuming sector with water demand. Since natural water resources cannot keep up with the demand, a shift from conventional water resources to unconventional ones is needed. While geothermal water was gaining importance for its energy content, small-scale (<10 L/s) energy plants were not required to reinject their spent geothermal brine. As geothermal resources align with agricultural areas in Western Anatolia, discharge of untreated brine might have severe adverse effects on crop yields and soil quality. In this study, we investigated use of spent geothermal brine for irrigation after treatment with Reverse Osmosis/Microbial Desalination Cell (RO/MDC) hybrid process. Treatment efficiencies for B, COD, As, Li, Fe, Cr concentrations and energy production values were determined. Treated water was initially evaluated for irrigation considering three quality categories (I, II, and III) comprised of parameters such as electrical conductivity (EC), total dissolved solids (TDS), and sodium adsorption ratio (SAR), along with sodium, chloride and boron concentrations. Additionally, magnesium adsorption ratio (MAR) and permeability index (PI) were used to evaluate for irrigation suitability. Although B concentrations in MDC-treated permeate (3.29 mg/L) and concentrate (2.99 mg/L) streams were not low enough to meet Quality I criterion (<0.7 mg/L), they can be still utilized in irrigation of moderate-to-high tolerant plants. Furthermore, PI and MAR parameters pointed to suitability for irrigational use. © 2022Correction Cpt-Based Liquefaction Resistance of Clean and Silty Sands: a Drainage Conditions Based Approach Nurhan Ecemis (aug, 10.1007/S10518-022-01501-0, 2022)(Springer, 2022) Arık, Mustafa Sezer; Ecemiş, Nurhan; Monkul, Mehmet Murat; Tütüncü, Yunus EmreArticle Citation - WoS: 7Citation - Scopus: 8Cpt-Based Liquefaction Resistance of Clean and Silty Sands: a Drainage Conditions Based Approach(Springer, 2022) Ecemis, Nurhan; Monkul, Mehmet Murat; Tütüncü, Yunus Emre; Arik, Mustafa SezerThe cone penetration test-based simplified liquefaction triggering evaluations are largely based on linking liquefaction manifestations in the field to cone penetration resistance. These relationships are interpreted in such a way that for given penetration resistance, the liquefaction resistance increases as non-plastic fines content (FC) increases. However, several studies have indicated discrepancies in this relationship. Hence, there is a lag in rational scientific understanding of this observation. In this study, an experimental research program was undertaken to investigate the CPT-based liquefaction assessment by considering the effects of drainage conditions on the relationship between CPT resistance and liquefaction resistance. First, clean sand and silty sands having 5, 15, and 35% FC were tested at different relative densities by stress-controlled cyclic direct simple shear (CDSS) tests to investigate cyclic resistance of silty sand with varying amounts of non-plastic fines. Then, a set of tests involving piezocone penetration (CPTu), seismic CPTu (SCPTu), and direct push permeability (DPPT) were undertaken in a large-scale box filled with the same soils used in the CDSS tests. The large-scale test results quantified the effect of drainage conditions (coefficient of consolidation) on cone penetration resistance. Finally, by combining the CDSS and CPTu test results, an alternative CPT-based liquefaction resistance relationship was proposed by considering the effects of drainage conditions.