Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Demirhan, Yasemin; Yiğen, Serap; Demirhan, Yasemin; Yiğen, Serap; Kosiel, Kamil; Kozubal, Maciej; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, Lütfi; Reno, John L.; Aygün, Gülnur; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.Article Citation - WoS: 33Citation - Scopus: 33Characterization of Thin Film Li0.5la0.5ti1-Xalxo3 Electrolyte for All-Solid Li-Ion Batteries(Elsevier, 2018) Ulusoy, Seda; Gülen, Sena; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, Mehtap; Özyüzer, Lütfi; Özdemir, Mehtap; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologySince addition of Al in Li0.5La0.5TiO3 has enhanced ionic conductivity in bulk materials, it is important to apply this material on all solid state thin film batteries. Because some of the good ionic conductors such as Lithium Phosphorus Oxynitride (LiPON) are sensitive to oxygen and moisture and their application is limited, so amorphous Li0.5La0.5Ti1−xAlxO3 (LLTAlO) is a most promising candidate because of its stability. In this study, the crystalline LLTAlO targets were prepared changing the amount of x content by conventional solid state reactions. Using these targets, lithium lanthanum titanium oxide (LLTO) thin film electrolytes were deposited on ITO/SLG substrates by radio frequency magnetron sputtering system in Ar atmosphere. The structural and compositional properties of targets and thin films were characterized by SEM, XRD, Raman spectroscopy and XPS. It was found that all targets are crystalline while the thin films are amorphous. To understand the effect of Al doping on ionic conductivity, electrical measurements were done at room temperature by AC impedance spectroscopy forming ITO/LLTAlO/Al structure like capacitor. Highest ionic conductivity result, 0.96 × 10−6 S·cm−1, is obtained from the nominal thin film composition of Li0.5La0.5Ti1−xAlxO3 (x = 0.05) at room temperature measurements. Heat treatment is also conducted to investigate to understand its effect on ionic conductivity and the structure of the thin films. It is found that ionic conductivity enhances with annealing. Also, temperature dependent ionic conductivity measurements from 298 K to 385 K are taken in order to evaluate activation energy for Li-ion conduction.Article Citation - WoS: 35Citation - Scopus: 38Influence of Sulfurization Temperature on Cu2znsns4 Absorber Layer on Flexible Titanium Substrates for Thin Film Solar Cells(IOP Publishing Ltd., 2018) Buldu, Dilara Gökçen; Cantaş, Ayten; Özyüzer, Lütfi; Akça, Fatime Gülşah; Meriç, Ece; Tarhan, Enver; Tarhan, Enver; Özyüzer, Lütfi; Aygün, Gülnur; Özdemir, Mehtap; Tarhan, Enver; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study, the effect of sulfurization temperature on the morphology, composition and structure of Cu2ZnSnS4 (CZTS) thin films grown on titanium (Ti) substrates has been investigated. Since Ti foils are flexible, they were preferred as a substrate. As a result of their flexibility, they allow large area manufacturing and roll-to-roll processes. To understand the effects of sulfurization temperature on the CZTS formation on Ti foils, CZTS films fabricated with various sulfurization temperatures were investigated with several analyses including x-ray diffraction (XRD), scanning electron microscopy (SEM), x-ray photoelectron spectroscopy and Raman scattering. XRD measurements showed a sharp and intense peak coming from the (112) planes of the kesterite type lattice structure (KS), which is strong evidence for good crystallinity. The surface morphologies of our thin films were investigated using SEM. Electron dispersive spectroscopy was also used for the compositional analysis of the thin films. According to these analysis, it is observed that Ti foils were suitable as substrates for the growth of CZTS thin films with desired properties and the sulfurization temperature plays a crucial role for producing good quality CZTS thin films on Ti foil substrates.