Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
8 results
Search Results
Article Investigations on the Effect of Secondary Treatments on Ti48Al2Cr2Nb Alloy Manufactured by Electron Beam Powder Bed Fusion Method(Elsevier Sci Ltd, 2025) Bilgin, Guney Mert; Ozer, Seren; Davut, Kemal; Esen, Ziya; Dericioglu, Arcan F.As-built Ti48Al2Cr2Nb alloy samples produced by electron beam powder bed fusion (PBF-EB) exhibited notable brittleness. The low ductility was attributed to coarse gamma bands aligned perpendicular to the building and tensile direction. Additionally, variations in aluminum content and hardness between the coarse colonies and fine gamma/alpha(2) lamellae contribute to this phenomenon. Electron backscattered diffraction (EBSD) studies revealed a higher amount of dislocation density and inherent strain after PBF-EB manufacturing. Hence, usage of Ti48Al2Cr2Nb alloy in the as-built condition in aviation applications with high loads and demanding environments is not found to be viable. To eliminate these negative aspects and make PBF-EB produced Ti48Al2Cr2Nb alloy available for demanding applications, two distinct post-processing heat treatments; namely, hot isostatic pressing (HIP) and annealing heat treatment (HT) were employed at 1200 degrees C. A comprehensive characterization covering microstructure analysis, EBSD, fracture surface examination, as well as room and high-temperature tensile tests allowed determination of the effect of post-processes. HIPing altered the banded structure observed in the as-built samples by increasing the amount of alpha(2) phase and grain size. On the other hand, HT made the banded structure more pronounced without significantly increasing the amount of alpha(2) phase. HT also strengthened the <001> texture, while HIPing introduced randomization of grains. On the other hand, complete recrystallization is achieved as a result of HT at 1200 degrees C for 2 h, whereas HIPing at the same temperature for 2 h induced only 80.5 % recrystallization. In both post-processes, dislocation density and inherent strain were reduced. Room temperature and high-temperature tensile tests demonstrated that both HIPing and HT eliminated the extreme brittleness of the as-built samples.Article Citation - WoS: 22Citation - Scopus: 25Effect of Solution Heat Treatment on the Microstructure and Crystallographic Texture of In939 Fabricated by Powder Bed Fusion-Laser Beam(Elsevier, 2023) Doğu, Merve Nur; Özer, Seren; Yalçın, Mustafa Alp; Davut, Kemal; Bilgin, Guney Mert; Obeidi, Muhannad Ahmed; Brodin, Hakan; Gu, Hengfeng; Brabazon, DermotThe effect of various solution heat treatment temperatures (i.e., 1120, 1160, 1200 and 1240 & DEG;C) on the microstructure, grain morphology and crystallographic texture of IN939 fabricated by powder bed fusion-laser beam (PBF-LB) was investigated. Microstructural analyses showed that the high-temperature gradient and rapid solidification of the PBF-LB processing caused different resulting microstructures compared to conventionally pro-duced counterparts. The melt pool morphologies and laser scanning paths were examined in the as-fabricated samples in the XZ-and XY-planes, respectively. After the application of solution heat treatment at 1120 & DEG;C, the as-fabricated PBF-LB initial microstructure was still apparent. For solution heat treatments of 1200 & DEG;C and above, the melt pool and scanning path morphologies disappeared and converted into a mixture of columnar grains in the XZ-plane and equiaxed grains in the XY-plane. On the other hand, large equiaxed grains were observed when the samples were solutionized at 1240 & DEG;C. Additionally, g' phase precipitated within the matrix after all solution heat treatment conditions, which led to increase in the microhardness values. According to electron backscatter diffraction (EBSD) analyses, both as-fabricated and solution heat-treated samples had intense texture with {001} plane normal parallel to the building direction. The first recrystallized grains began to appear when the samples were subjected to the solution heat treatment at 1160 & DEG;C and the fraction of the recrystallized grains increased with increasing temperature, as supported by kernel average misorientation (KAM) and grain spread orientation (GOS) analyses.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).Article Citation - WoS: 29Citation - Scopus: 31Effect of Heat Input on Haz Softening in Fiber Laser Welding of 22mnb5 Steel(Elsevier, 2023) Tuncel, Oğuz; Aydın, Hakan; Davut, KemalThis study investigates the effects of heat input on the heat-affected zone (HAZ) softening in fiber laser welding of quenched 1.1 mm thick 22MnB5 steel. Laser power (1500-2500 W) and welding speed (40-120 mm/s) parameters are considered as the input process variables. Depending on the input parameters, the applied heat input varied between 12.5 and 62.5 J/mm. The results indicate that a minimum heat input of 50 J/mm is required for full weld penetration. Microhardness findings revealed that the drop in hardness in the HAZ region relative to the base material (BM) reached 39% due to grain coarsening caused by an increase in heat input under the welding conditions. Grain coarsening (prior austenite grains) is also detected in SEM analysis. In addition, grain coarsening at high heat input was also determined quantitatively in EBSD analyses. The proportion of 8.91 mu m grain size in the sample with high heat input is 4.2%, while it is 1.2% in the sample with low heat input. When the heat input increased from 12.5 to 62.5 J/mm, the width of the softened zone with the lowest hardnesses in the HAZ grew from 0.2 mm to 2.2 mm.Article Citation - WoS: 14Citation - Scopus: 13An Experimental Study on the Ballistic Performance of Ultra-High Hardness Armor Steel (armox 600t) Against 7.62 Mm × 51 M61 Ap Projectile in the Multi-Hit Condition(Elsevier, 2023) Göde, Engin; Teoman, Atanur; Çetin, Barış; Tonbul, Kürşat; Davut, Kemal; Kuşhan, Melih CemalIn this study, Armox 600T armor steel was ballistically tested against 7.62 mm × 51 M61 AP projectile. The experimental design was constructed on the basis of the worst-case scenario which is the highest possible impact velocity in the multi-hit condition. The ballistic tests revealed that Armox 600T could defeat the worst-case scenario with a thickness of 12 mm. Furthermore, the damaged and undamaged regions were inspected microstructurally in a detail manner aiming to observe the possible fractographic modes of the studied material. Finally, high resolution optical scanning efforts were also added to the experimental work whose results uncovers the possible improvement areas regarding the quantification of the results of ballistic testing.Article Citation - WoS: 45Citation - Scopus: 48Recrystallization and Grain Growth Kinetics of In718 Manufactured by Laser Powder Bed Fusion(Elsevier, 2022) Doğu, Merve Nur; Davut, Kemal; Obeidi, Muhannad Ahmed; Yalçın, Mustafa Alp; Gu, Hengfeng; Low, Thaddeus Song En; Ginn, Jon; Brabazon, DermotThe recrystallization and grain growth behaviour of IN718 alloy additively manufactured by laser powder bed fusion (L-PBF) is presented herein. The effects of three different temperatures (1050, 1150 and 1250 °C) and holding times (15, 45 and 90 min) were investigated. The texture evolution of the samples was recorded via electron backscatter diffraction (EBSD). The as-built sample is composed of bowl-shaped melt pools, a chessboard-like grain pattern and has a cube texture {100}<001>. Recrystallized grains were observed in the samples treated at 1150 °C for 15 min, as well as the samples treated for longer periods and at higher temperatures. Recrystallization was observed to start from high dislocation density regions, including the overlapping melt pools and the borders of the chessboard-like pattern. The initial cube texture transforms into a first-generation cube-twin texture {122}<212> via a twinning-assisted recrystallization mechanism. Then, those recrystallization nuclei sweep through the high defect density matrix; during which almost no new twins are formed. The samples treated at 1250 °C are almost completely recrystallized, which forms a weaker cube texture and a stronger P-orientation {011}<112>. However, the growth of recrystallized grains is very limited due to the presence of non-coherent precipitates.Article Citation - WoS: 8Citation - Scopus: 8Design and Fabrication of Polymer Micro/Nano Composites With Two-Level Mechanical Reinforcing Procedure(Wiley, 2022) Kandemir, Ayşe Çağıl; Dönmez, Fatma; Davut, Kemal; Kaplan Can, HaticeBiocompatible composite production was accomplished by utilizing two-level hierarchical approach for mechanical reinforcement. A well-known commodity polymer; low-density polyethylene (LDPE), which has high-fracture toughness, yet low strength and modulus was used as the main matrix material. As the first step of hierarchy, ductile LDPE was blended with brittle polyvinylpyrrolidone (PVP), which is an eco-friendly, nontoxic and biocompatible polymer. This resulted in slight decrease of strength and drastic reduction of toughness (%70), yet modulus was increased by 78%. As the second level of hierarchy, PVP composites were introduced in LDPE. Nano-scaled Halloysite clay and micro-scaled spherical Silica particles were utilized as additives in the aforementioned PVP composites. The reason for the choice of these particles is that they are nontoxic, low-cost and in the case of Halloysite; abundant in nature. Owing to the implementation of the second level; modulus improvement was further enhanced to 150%, with additional benefits of strength increase up to 17% and less reduction in fracture toughness (minimum 51% reduction). Dynamic mechanical analysis also supported these outcomes that storage modulus of composites are higher than both LDPE and LDPE-PVP blend. The proposed biocompatible composites in the end of this study would be utilized in biomedical applications necessitating mechanical improvements.Article Citation - WoS: 6Citation - Scopus: 6A Numerical Methodology for Monitoring Stress Distributions and Experimental Proof of the Concept on Metal Embedded Thin Polymer-Matrix Composites Using X-Ray Diffraction(Elsevier, 2022) Demir, Eralp; Sas, Hatice S.; Işık, Murat; Aydoğan Güngör, Eda; Davut, KemalIn this study, a numerical methodology is developed to monitor stress distributions and an experimental technique is investigated to measure stresses on metal embedded polymer matrix fiber-reinforced composite materials using X-ray diffraction (XRD) method. The numerical method successfully predicts the stress distributions using only a few data points with an average accuracies of 11.6% and 11.8%, respectively for tapered and open hole tensile sample geometries. Experimental part of this study investigates different methodologies to measure stresses on surfaces of polymer composites materials of thin walled structures by XRD. For this reason, metallic materials were integrated onto the surface and near-surface of polymer matrix composites in three different configurations as in the forms of metal foil, metal powder, and metal wire mesh. In-situ experiments of measured and applied stresses revealed metal powder embedded composite materials as a promising material configuration for reliable monitoring of stresses.Article Citation - WoS: 39Citation - Scopus: 41Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier, 2022) Özer, Seren; Bilgin, Güney Mert; Davut, Kemal; Esen, Ziya; Dericioğlu, Arcan.FThe effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples disappeared and converted into a mixture of columnar and equiaxed grains. Nano-sized γ″ and/or γ′ precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 °C for 8 h) tested at 600 °C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700–800 °C, which was attributed to intermediate temperature embrittlement.