Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

20223

Settings

Institution Author: search.filters.institutionAuthor.Davut, KemalWoS Q: search.filters.wosQuartile.Q2

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 3
    Citation - Scopus: 4
    Partial Austenitisation and Tbf Steel Composed of Ferrite, Bainitic Ferrite, and Austenite
    (Taylor & Francis, 2022) Erişir, Ersoy; Bilir, Oğuz Gürkan; Sözer, Yunus Emre; Ararat, Özge; Davut, Kemal
    A TRIP-aided bainitic-ferritic (TBF) steel with a chemical composition of Fe-0.19C-1.7Mn-1.09Si-0.51Al-0.05Nb (wt-%) was partially austenitised from a hot-rolled martensitic initial microstructure. After the hot rolling, the martensitic specimens were reheated to different intercritical temperatures and then austempered at 350 degrees C. Thus, the effect of the initial microstructure of TBF steel on intercritical austenite formation during partial austenitisation was studied. The microstructures were investigated by scanning electron microscopy and electron backscatter diffraction (EBSD), and the tensile properties were tested. Microstructural observations revealed that a final microstructure of fine ferrite, bainitic ferrite, and retained austenite can be obtained. The steel partial austenitised at 770 degrees C showed a good combination of ultimate tensile strength and total elongation.
  • Article
    Citation - WoS: 8
    Citation - Scopus: 8
    Design and Fabrication of Polymer Micro/Nano Composites With Two-Level Mechanical Reinforcing Procedure
    (Wiley, 2022) Kandemir, Ayşe Çağıl; Dönmez, Fatma; Davut, Kemal; Kaplan Can, Hatice
    Biocompatible composite production was accomplished by utilizing two-level hierarchical approach for mechanical reinforcement. A well-known commodity polymer; low-density polyethylene (LDPE), which has high-fracture toughness, yet low strength and modulus was used as the main matrix material. As the first step of hierarchy, ductile LDPE was blended with brittle polyvinylpyrrolidone (PVP), which is an eco-friendly, nontoxic and biocompatible polymer. This resulted in slight decrease of strength and drastic reduction of toughness (%70), yet modulus was increased by 78%. As the second level of hierarchy, PVP composites were introduced in LDPE. Nano-scaled Halloysite clay and micro-scaled spherical Silica particles were utilized as additives in the aforementioned PVP composites. The reason for the choice of these particles is that they are nontoxic, low-cost and in the case of Halloysite; abundant in nature. Owing to the implementation of the second level; modulus improvement was further enhanced to 150%, with additional benefits of strength increase up to 17% and less reduction in fracture toughness (minimum 51% reduction). Dynamic mechanical analysis also supported these outcomes that storage modulus of composites are higher than both LDPE and LDPE-PVP blend. The proposed biocompatible composites in the end of this study would be utilized in biomedical applications necessitating mechanical improvements.
  • Article
    Citation - WoS: 6
    Citation - Scopus: 6
    Texture Evolution of Friction Stir-Processed Dual-Phase Steel
    (Springer, 2022) Aktarer, Semih Mahmut; Küçükömeroğlu, Tevfik; Davut, Kemal
    Evolution of crystallographic texture and local strains in different zones of a dual-phase steel subjected to severe plastic deformation by friction stir process was examined by electron backscatter diffraction technique. Misorientations, which were expressed by the values of grain orientation spread and kernel average misorientation (KAM), increased from the thermomechanical affected zone (TMAZ) to pin-affected stir zone (PE-SZ). KAM maps showed that the highest local strain appeared in the PE-SZ. Misorientation distributions were found to be consistent with microhardness distributions in the processed region. The crystallographic texture of base metal, heat-affected zone, and TMAZ was similar. Recrystallization and deformation texture components were observed at stir zones, and recrystallization texture components decreased drastically at PE-SZ. Rotated cube, goss and rotated goss texture components were detected at PE-SZ. Rotated cube texture component indicates partial recrystallization after plastic deformation. Shear texture components were determined using shear direction (SD) as reference. Different shear texture components (111), (112), and (101)