Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

2008 - 200912010 - 201912020 - 20221

Settings

Institution Author: search.filters.institutionAuthor.Güden, MustafaSubject: search.filters.subject.Strain rate sensitivity

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 28
    Citation - Scopus: 34
    The Strain Rate Sensitive Flow Stresses and Constitutive Equations of a Selective-Laser and an Annealed-Rolled 316l Stainless Steel: a Comparative Study
    (Elsevier, 2022) Güden, Mustafa; Enser, Samed; Bayhan, Mesut; Taşdemirci, Alper; Yavaş, Hakan
    The strain rate dependent compressive flow stresses of a Selective-Laser-Melt 316L (SLM-316L) alloy and a commercial (annealed-extruded) 316L (C-316L) alloy were determined, for comparison, between 1x10-4 and ∼2500 s-1 and between 1x10-4 and ∼2800 s-1, respectively. The Johnson and Cook flow stress material model parameters of both alloys were also determined. The microstructural examinations of the deformed cross-sections of tested specimens (interrupted tests) showed a twinning-induced-plasticity in SLM-316L alloy and a martensitic transformation-induced-plasticity in C-316L alloy. Twin and martensite formations were detected microscopically higher in the dynamically tested specimens until about 0.22 strain, while the twin and martensite formations decreased at increasing strains due to adiabatic heating. The rate sensitivity of SLM-316L was determined slightly higher than that of C-316L within the quasi-static strain rate range (1x10-4 and 1x10-2 s-1), while the rate sensitivities of both alloys were similar in the quasi-static-high strain rate range (1x10-4 and ∼2500-2800 s-1) at low strains. A more rapid decrease in the rate sensitivity of C-316L at increasing strains was found in the quasi-static-high strain rate range. The similar activation volumes of both alloys, corresponding to the dislocation intersections, indicated a similar thermally activated deformation process involvement in both alloys.
  • Article
    Citation - WoS: 41
    Citation - Scopus: 38
    Simulation of the Strain Rate Sensitive Flow Behavior of Sic-Particulate Reinforced Aluminum Metal Matrix Composites
    (Elsevier Ltd., 2008) Tirtom, İsmail; Güden, Mustafa; Yıldız, Hasan
    Strain rate dependent compression mechanical behavior of an SiC-particulate reinforced Al (2024-O) metal matrix composite (MMC) with different particle volume fractions was numerically investigated at various strain rates. Calculations were performed using axisymmetric finite element unit cell model, in which an elastic SiC particle was embedded inside a strain rate sensitive viscoplastic Al matrix. Stress–strain curves of Al matrix material were derived from Split Hopkinson Pressure Bar experiments at various strain rates and used as inputs in the FEM model. Numerically computed stress–strain curves and strain rate sensitivity were compared with those of experiments for a 15% SiC-particulate reinforced MMC. Computed strain rate sensitivity of the MMC was found to be higher than that of the matrix alloy and increased with increasing strain contrary to the strain independent matrix strain rate sensitivity. The strain rate sensitivity of the MMC was also found to increase with increasing particle volume fraction at the same particle size. Finally, several possible reasons including assumptions used in the model, adiabatic heating, microstructural variations between the composite matrix and matrix alloy, particle shape and distribution and damage accumulation for the small discrepancy found between computed and experimental stress–strain curves and strain rate sensitivity of the composite were discussed.
  • Article
    Citation - WoS: 3
    Citation - Scopus: 5
    The Effect of Strain Rate on the Mechanical Behavior of Teflon Foam
    (Elsevier Ltd., 2012) Taşdemirci, Alper; Turan, Ali Kıvanç; Güden, Mustafa
    The quasi-static (1 × 10−3, 1 × 10−2 and 1 × 10−1 s−1) and high strain rate (7200 and 9500 s−1) experimental and high strain rate numerical compression deformation of a Gore Polarchip™ CP7003 heat insulating Teflon foam was investigated. High strain rate tests were conducted with the insertion of quartz crystal piezoelectric transducers at the end of the transmitter bar of a compression Split Hopkinson Pressure Bar (SHPB) set-up in order to measure the force at the back face of the specimen. A fully developed numerical model of the SHPB test on Teflon was also implemented using LS-DYNA. The simulation stresses showed close correlations with the experimentally measured stresses on the bars. The developed model successfully simulated the high strain rate loading. The damage initiation and progression of experimental high strain rate tests were further recorded using a high speed camera and found to be very similar to those of the simulation high strain rate tests.