Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
11 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 9Quasi-Static and High Strain Rate Properties of a Cross-Ply Metal Matrix Composite(Elsevier Ltd., 2009) Hall, Ian W.; Taşdemirci, Alper; Derrick, J.A series of compression tests has been carried out at quasi-static and high strain rates on cylindrical samples of an alumina fiber/Al-6061 metal matrix composite. The composite plates were prepared with fibers in the 0°, 0/90° and ±45° orientations. It was found that the mechanical properties were strongly dependent upon the imposed strain rate, with fracture stress increases of >50% being noted for several orientations at high strain rates: these increases are not believed to be related to strain rate sensitivity of either the matrix or fibers but to arise from the inertia of fragments which remain in place after fracture and continue to bear load. Also, and in contradiction to behavior anticipated from the rule of mixtures, it was found that 0/90° samples exhibited properties superior to those of 0° unidirectional samples. High-speed photography was used to confirm the sequence of deformation and fracture events at high strain rate. © 2008 Elsevier B.V. All rights reserved.Article Citation - WoS: 33Citation - Scopus: 41Development of Novel Multilayer Materials for Impact Applications: a Combined Numerical and Experimental Approach(Elsevier Ltd., 2009) Taşdemirci, Alper; Hall, Ian W.A well-verified and validated numerical model was used to investigate stress wave propagation in a multilayer material subjected to impact loading. The baseline material consisted of a ceramic faceplate and composite backing plate separated by a rubber or teflon foam interlayer: several variants were investigated in which the number, type, and total thicknesses of the interlayers were altered. Comparison of the variants showed that the use of multiple teflon foam interlayers could drastically reduce the average stress in the multilayer material. Based on the numerical results, further experimental work was undertaken upon one of the variants. Very large and unexpected tensile stress oscillations were observed in the ceramic layers, leading to a refinement of the numerical model which successfully reproduced the oscillations and also demonstrated that separation of the sample layers led to trapping of the stress wave within the layers. Use of the validated numerical model allowed detailed analysis of the processes of wave transmission and demonstrates the important synergy that can exist between experimental and modeling studies. The current study provides a valuable starting point for designing future multilayer materials with specific, controlled properties.Article Citation - WoS: 17Citation - Scopus: 20Numerical and Experimental Studies of Damage Generation in a Polymer Composite Material at High Strain Rates(Elsevier Ltd., 2006) Taşdemirci, Alper; Hall, Ian W.Samples of S2-glass/epoxy composites have been subjected to microstructural investigation after testing in compression at quasi-static and high strain rates using the split Hopkinson pressure bar. A numerical model was developed that accurately describes the high strain rate mechanical response of the samples. Moreover, in contrast with earlier phenomenological or constitutive models, the model can also predict a variety of failure modes such as delamination, matrix cracking or fiber crushing. High-speed photography was used to check the model results. Interrupted tests, followed by metallographic examination, have revealed that the sequence of damage events differs between quasi-static and high strain rate regimes. The effect of sample size on measured mechanical properties is noted and is confirmed via numerical modeling.Article Citation - WoS: 29Citation - Scopus: 38The Effects of Plastic Deformation on Stress Wave Propagation in Multi-Layer Materials(Elsevier Ltd., 2007) Taşdemirci, Alper; Hall, Ian W.The behavior of a multi-layer material at high strain rate and the effect of plastic deformation on stress wave propagation were investigated by a combination of experimental and numerical techniques. Plastic deformation effects were studied in multi-layer materials consisting of ceramic, copper and aluminum subjected to large strains under high strain rate loading. First, stress wave propagation behavior for the monolithic metals was studied, and then extended to multilayer combinations of these metals with each other and with a ceramic layer. The axial stress distributions were found to be non-uniform in the elastic deformation range of the specimen. The degree of non-uniformity was much more pronounced in the multi-layer samples consisting of different materials. The presence of a ceramic layer increased the magnitudes of stress gradients at the interfaces. It was also found that a major effect of plastic deformation is a tendency to produce a more homogeneous stress distribution within the components. The implications of these observations for practical systems are discussed.Article Citation - WoS: 27Citation - Scopus: 28Split Hopkinson Pressure Bar Multiple Reloading and Modeling of a 316 L Stainless Steel Metallic Hollow Sphere Structure(Elsevier Ltd., 2010) Taşdemirci, Alper; Ergönenç, Çağrı; Güden, MustafaThe high strain rate (600 s−1) compression deformation of a 316 L metallic hollow sphere (MHS) structure (density: 500 kg m−3; average outer hollow sphere diameter: 2 mm and wall thickness: 45 μm) was determined both numerically and experimentally. The experimental compressive stress–strain behavior at high strain rates until about large strains was obtained with multiple reloading tests using a large-diameter compression type aluminum Split Hopkinson Pressure Bar (SHPB) test apparatus. The multiple reloading of MHS samples in SHPB was analyzed with a 3D finite element model using the commercial explicit finite element code LS-DYNA. The tested MHS samples showed increased crushing stress values, when the strain rate increased from quasi-static (0.8 × 10−4 s−1) to high strain rate (600 s−1). Experimentally and numerically deformed sections of MHS samples tested showed very similar crushing characteristics; plastic hinge formation, the indentation of the spheres at the contact regions and sphere wall buckling at intermediate strains. The extent of micro-inertial effects was further predicted with the strain rate insensitive cell wall material model and with the strain rate sensitive behavior of MHS structure similar to that of the cell wall material. Based on the predictions, the strain rate sensitivity of the studied 316 L MHS sample was attributed to the strain rate sensitivity of the cell wall material and the micro-inertia.Article Citation - WoS: 32Citation - Scopus: 37Modeling Quasi-Static and High Strain Rate Deformation and Failure Behavior of a (±45) Symmetric E-glass/Polyester Composite Under Compressive Loading(Elsevier Ltd., 2013) Kara, Ali; Taşdemirci, Alper; Güden, MustafaQuasi-static (1 × 10−3–1 × 10−2 s−1) and high strain rate (∼1000 s−1) compressive mechanical response and fracture/failure of a (±45) symmetric E-glass/polyester composite along three perpendicular directions were determined experimentally and numerically. A numerical model in LS-DYNA 971 using material model MAT_162 was developed to investigate the compression deformation and fracture of the composite at quasi-static and high strain rates. The compressive stress–strain behaviors of the composite along three directions were found strain rate sensitive. The modulus and maximum stress of the composite increased with increasing strain rate, while the strain rate sensitivity in in-plane direction was higher than that in through-thickness direction. The damage progression determined by high speed camera in the specimens well agreed with that of numerical model. The numerical model successfully predicted the damage initiation and progression as well as the failure modes of the composite.Article Citation - WoS: 22Citation - Scopus: 28Mechanical Interlocking Between Porous Electrospun Polystyrene Fibers and an Epoxy Matrix(American Chemical Society, 2014) Demir, Mustafa Muammer; Horzum, Nesrin; Taşdemirci, Alper; Turan, Ali Kıvanç; Güden, MustafaAn epoxy matrix filled with nonwoven mats of porous polystyrene (PS) fibers processed by an electrospinning was compression tested at quasi-static (1 × 10–3 s–1) and high strain (315 s–1) rates. The electrospun PS fibers with a diameter between 6 and 9 μm, accommodated spherical pores on the surface with the sizes ranging from 0.1 to 0.2 μm. The filling epoxy matrix with 0.2 wt % PS fibers increased the compressive elastic modulus and compressive strength over those of neat epoxy resin. The microscopic observations indicated that the surface pores facilitated the resin intrusions into the fiber, enhancing the interlocking between resin and fibers, and increased the deformation energy expenditure of the polymer matrix.Article Citation - WoS: 11Citation - Scopus: 10Experimental Testing and Full and Homogenized Numerical Models of the Low Velocity and Dynamic Deformation of the Trapezoidal Aluminium Corrugated Core Sandwich(John Wiley and Sons Inc., 2014) Kılıçaslan, Cenk; Odacı, İsmet Kutlay; Taşdemirci, Alper; Güden, MustafaThe simulations of the low velocity and dynamic deformation of a multi-layer 1050-H14 Al trapezoidal zig-zag corrugated core sandwich were investigated using the homogenized models (solid models) of a single core layer (without face sheets). In the first part of the study, the LS-DYNA MAT-26 material model parameters of a single core layer were developed through experimental and numerical compression tests on the single core layer. In the second part, the fidelities of the developed numerical models were checked by the split-Hopkinson pressure bar direct impact, low velocity compression and indentation and projectile impact tests. The results indicated that the element size had a significant effect on the initial peak and post-peak stresses of the homogenized models of the direct impact testing of the single-layer corrugated sandwich. This was attributed to the lack of the inertial effects in the homogenized models, which resulted in reduced initial peak stresses as compared with the full model and experiment. However, the homogenized models based on the experimental stress–strain curve of the single core layer predicted the low velocity compression and indentation and projectile impact tests of the multi-layer corrugated sandwich with an acceptable accuracy and reduced the computational time of the models significantly.Conference Object Citation - WoS: 11Citation - Scopus: 18Experimental and Numerical Investigation of High Strain Rate Mechanical Behavior of a [0/45 - 45] Quadriaxial E-glass/Polyester Composite(Elsevier Ltd., 2011) Taşdemirci, Alper; Kara, Ali; Turan, Ali Kıvanç; Tunusoğlu, Gözde; Güden, Mustafa; Hall, Ian W.Quasi-static (10−3–10−1 s−1) and high strain rate (∼900 s−1) compression behavior of an E-Glass fiber woven fabric reinforced Polyester matrix composites was investigated by using a Shimadzu AG-I testing machine and a Split Hopkinson Pressure Bar apparatus in the Dynamic Testing and Modeling Laboratory of Izmir Institute of Technology. During the experiments, a high speed camera was used to determine deformation behavior. In both directions, modulus and failure strength increased with increasing strain rate. Higher strain rate sensitivity for both elastic modulus and failure strength was observed in the in-plane direction. Based upon these experimental data, a numerical model was developed using the commercial explicit finite element code LS-DYNA to investigate compressive deformation and damage behavior of composites. Excellent agreement was demonstrated for the case of high strain rate loading. Also, the fracture geometries were successfully predicted with the numerical model.Article Citation - WoS: 19Citation - Scopus: 21Effect of Strain Rate on the Compressive Mechanical Behavior of a Continuous Alumina Fiber Reinforced Ze41a Magnesium Alloy Based Composite(Elsevier Ltd., 2006) Güden, Mustafa; Akil, Övünç; Taşdemirci, Alper; Çiftçioğlu, Muhsin; Hall, Ian W.The compressive mechanical response of an FP™ continuous fiber (35 vol.%) Mg composite has been determined in the transverse and longitudinal directions at quasi-static and high strain rates. It was found that the composite in the transverse direction exhibited strain rate sensitivity of the flow stress and maximum stress within the studied strain-rate range of 1.3 × 10−4 to 1550 s−1. The failure strain in this direction, however, decreased with increasing strain rate. Microscopic observations on the failed samples have shown that the composite failed by shear banding along the diagonal axis, 45° to the loading axis. Twinning was observed in the deformed cross-sections of the samples particularly in and near the shear band region. The strain rate sensitivity of the fracture stress of the composite in transverse direction is attributed to the matrix strain rate sensitivity. In the longitudinal direction, the composite failed by kink formation at quasi-static strain rates, while kinking and splitting were observed at the high strain rates. The maximum stress in the longitudinal direction was, however, found to be strain rate insensitive within the strain rate regime of 1.3 × 10−4 to 500 s−1. In this direction, similar to transverse direction, twinning was observed in the highly deformed kink region. Several different reasons are proposed for the strain rate insensitive compressive strength in this direction.