Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
20 results
Search Results
Article Citation - WoS: 28Citation - Scopus: 29Oxidation of Nanocrystalline Aluminum by Variable Charge Molecular Dynamics(Elsevier Ltd., 2010) Perron, A.; Garruchet, S.; Politano, O.; Aral, Gürcan; Vignal, V.We investigate the oxidation of nanocrystalline aluminum surfaces using molecular dynamics (MD) simulations with the variable charge model that allows charge dynamically transfer among atoms. The interaction potential between atoms is described by the electrostatic plus (Es+) potential model, which is composed of an embedded atom method potential and an electrostatic term. The simulations were performed from 300 to 750 K on polycrystalline samples with a mean grain size of 5 nanometers. We mainly focused on the effect of the temperature parameter on the oxidation kinetic. The results show that, beyond a first linear regime, the kinetics follows a direct logarithmic law (governed by diffusion process) and tends to a limiting value corresponding to a thickness of similar to 3 nm. We also characterized at 600 K the effects of an external applied strain on the microstructure and the chemical composition of oxide films formed at the surface. In particular, we obtained a partially crystalline oxide films for all temperatures and we noticed a strong correlation between the degree of crystallinity of the oxide film and the oxidation temperature. (C) 2009 Elsevier Ltd. All rights reserved.Article Citation - WoS: 7Citation - Scopus: 8Investigation of the Structural and Optical Properties of Copper-Titanium Oxide Thin Films Produced by Changing the Amount of Copper(Elsevier Ltd., 2019) Horzum, Şeyda; Gürakar, Sibel; Serin, TülayWe examine how the structural, morphological and optical properties of TiO2 thin films are changed with heavily copper (Cu) content. Variations in characteristic properties of the films with 0, 12.5, 25 and 50 wt% Cu contents, grown by sol-gel dip coating method, are observed by using X-ray diffraction (XRD), Raman scattering, atomic force microscopy, energy dispersive X-ray analysis and optical spectroscopy measurements. The XRD and Raman spectra indicate that pure TiO2 film forms in the anatase structure. At high Cu concentrations, XRD results also reveal the substitution of Ti with Cu and formation of extra compound Copper-Titanium oxide. Raman measurements also show that Cu is incorporated homogeneously into TiO2 matrix up to 12.5 wt% concentration and this uniformity is distorted at higher Cu contents. In addition, optical spectroscopy measurements show that the optical band gap energy decreases from 3.26 eV to 2.05 eV with increasing Cu concentration. Furthermore, it is observed that the refractive index values obtained by means of transmittance spectra at 550 nm wavelength; increases from 2.47 to 3.39 when the Cu concentration increases from 0 to 50 wt %.Editorial Preface(Elsevier Ltd., 2017) Özyüzer, Lütfi; Kosiel, Kamil; Reno, John L.; Basa, Deekpak KumarIt is our pleasure to publish the proceedings of selected papers from the Science and Applications of Thin Films, Conference & Exhibition (SATF2016) in a Special Issue of Thin Solid Films. SATF2016 was held at the Ilica Hotel Spa & Wellness Thermal Resort, Cesme, Izmir, Turkey, from September 19 to 23, 2016. It was a very successful conference with over 241 abstracts submitted from33 countries, including 30 invited talks, 61 contributed talks, and over 150 poster presentations. More information about the conference can be found at http://www. satf2016.org/Article Citation - WoS: 51Citation - Scopus: 48Cu2znsns4-Based Thin Films and Solar Cells by Rapid Thermal Annealing Processing(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Klaer, J.; Mainz, R.; Özyüzer, Lütfi; Unold, T.In this study, kesterite Cu2ZnSnS4 (CZTS) absorber layers were fabricated by DC magnetron sputtering deposition of metallic Cu-Zn-Sn precursors, followed by an annealing treatment in sulfur vapor atmosphere at 600 °C for 3 min using rapid thermal processing (RTP). Three types of stacked metallic films were prepared and included pre-annealing of Cu-Sn stacks in order to induce preferential Cu-Sn alloying. The chemical composition of the sulfurized films was obtained by X-ray fluorescence (XRF) before and after etching the samples in KCN solution. All CZTS thin films are found to be Cu-poor and Zn-rich. Structural characterizations were performed by X-ray diffraction (XRD) and Raman spectroscopy to investigate the impact of pre-annealing on the structural properties of the precursors and final CZTS films. Glow discharge optical emission spectroscopy (GDOES) shows that pre-annealing of the precursors can improve depth homogeneity of the CZTS films. Photoluminescence spectra and the optical band gap energy values are compatible with literature. Selected samples were processed to solar cells and characterized.Article Citation - WoS: 22Citation - Scopus: 23Effect of Heat Treating Metallic Constituents on the Properties of Cu2znsnse4 Thin Films Formed by a Two-Stage Process(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Başol, B. M.; Atasoy, Y.; Tomakin, Murat; Aygün, Gülnur; Özyüzer, Lütfi; Bacaksız, EminIn this study Cu2ZnSnSe4 (CZTSe) thin films were grown by a two-stage process that involved sputter deposition of a Cu/Sn/Zn/Cu metallic stack, annealing the stack at various temperatures for 30 min, evaporation of a Se cap over the metallic stack thus forming a precursor layer, and subjecting the precursor layer to a final high temperature reaction step at 550 °C. Different samples were prepared with annealing temperatures of the metallic stacks ranging from 200 °C to 350 °C. The results showed that heat treatment of the metallic stacks did not cause much change in their morphology and elemental composition, however their phase content changed noticeably when the anneal temperature was raised to 250 °C. Specifically, while the metallic films were dominated by CuSn and Cu5Zn8 phases at low temperatures, the dominant phase shifted to Cu6Sn5 at the annealing temperature of 250 °C and higher. Also formation of a distinct Cu3Zn2 phase was observed upon annealing at temperatures at or above 250 °C. After reaction with Se, the CZTSe layer obtained from the metallic film, which was annealed at 250 °C was found to be the best n terms of its composition, crystalline quality and purity, although it contained a small amount of CuSe. The other layers were found to contain small amounts of other secondary phases such as SnSe, CuSe2, ZnSe and Cu2SnSe3. SEM micrographs showed denser structure for CZTSe layers grown from metallic films annealed at or above 250 °C. Optical band gap, resistivity and carrier concentration of the best quality CZTSe film were found to be about 0.87 eV, 2 Ω-cm and 4 × 1017 cm− 3, respectively.Article Citation - WoS: 5Citation - Scopus: 4The Effect of Annealing Temperature on the Optical Properties of a Ruthenium Complex Thin Film(Elsevier Ltd., 2016) Ocakoğlu, Kasım; Okur, Salih; Aydın, Hasan; Emen, Fatih MehmetThe stability of the optical parameters of a ruthenium polypyridyl complex (Ru-PC K314) film under varying annealing temperatures between 278 K and 673 K was investigated. The ruthenium polypyridyl complex thin film was prepared on a quartz substrate by drop casting technique. The transmission of the film was recorded by using Ultraviolet/Visible/Near Infrared spectrophotometer and the optical band gap energy of the as-deposited film was determined around 2.20 eV. The optical parameters such as refractive index, extinction coefficient, and dielectric constant of the film were determined and the annealing effect on these parameters was investigated. The results show that Ru PC K314 film is quite stable up to 595 K, and the rate of the optical band gap energy change was found to be 5.23 × 10- 5 eV/K. Furthermore, the thermal analysis studies were carried out in the range 298-673 K. The Differential Thermal Analysis/Thermal Gravimmetry/Differantial Thermal Gravimmetry curves show that the decomposition is incomplete in the temperature range 298-673 K. Ru-PC K314 is thermally stable up to 387 K. The decomposition starts at 387 K with elimination of functional groups such as CO2, CO molecules and SO3H group was eliminated between 614 K and 666 K.Article Citation - WoS: 36Citation - Scopus: 37Influence of Copper Composition and Reaction Temperature on the Properties of Cztse Thin Films(Elsevier Ltd., 2016) Olgar, Mehmet Ali; Atasoy, Y.; Başol, B. M.; Tomakin, Murat|Özyüzer, Gülnur Aygün; Özyüzer, Lütfi; Bacaksız, EminIn this study Cu2ZnSnSe4 (CZTSe) compound layers were grown using a two-stage technique that involved deposition of metallic precursors (Cu, Zn, and Sn) and Se in the first stage, followed by reaction of all the species at temperatures between 525 °C and 600 °C, during the second stage of the process. Two sets of samples, one with Cu-poor, Zn-rich and the other with Cu-rich, Zn-rich compositions, were prepared and their structural, optical and electrical properties were measured. XRD analyses showed the characteristic peaks of CZTSe regardless of the Cu content and the processing temperature. However, for samples reacted at temperatures of 575 °C and 600 °C a Cu2-xSe secondary phase separation was detected for all films suggesting that the reaction temperatures should be limited to values below 575 °C in a two-stage process such as ours. Excessive Sn loss was also present in samples processed at the highest temperatures. Raman scattering measurements confirmed formation of the CZTSe kesterite structure, and also indicated a small ZnSe phase, which could not be detected by XRD. Scanning electron micrographs demonstrated dense film structure with the Cu-rich films having smoother morphology. Optical characterization showed that increasing the Cu content in the compound layers caused a reduction in the optical band gap values due to increased interaction between the Cu-3d orbital electrons and the Se-4p orbital electrons. Electrical measurements showed that the carrier concentration increased with Cu content.Article Citation - WoS: 60Citation - Scopus: 64Improvement of Optical and Electrical Properties of Ito Thin Films by Electro-Annealing(Elsevier Ltd., 2015) Köseoğlu, Hasan; Türkoğlu, Fulya; Kurt, Metin; Yaman, Mutlu Devran; Akça, Fatime Gülşah; Aygün, Gülnur; Özyüzer, LütfiThe effect of electro-annealing in vacuum and air on the optical and electrical properties of ITO thin films grown by large area DC magnetron sputtering was investigated. Moreover, the performances of the electro-annealed ITO thin films in vacuum and air were compared. Electro-annealing was performed by applying 0.75, 1.00, 1.25 and 1.50 A constant ac current to the ITO thin films. It was observed that the crystallinity of the films was better for the ITO thin films electro-annealed in vacuum. The changes in sheet resistance of electro-annealed ITO thin films with applied currents were detailed. The transmittance of the films increased for both electro-annealing in vacuum and air. A correlation between band-gap and resistivity for all of the electro-annealed thin films was observed.Article Citation - WoS: 18Citation - Scopus: 18The Effects of the Post-Annealing Time on the Growth Mechanism of Bi2sr2ca1cu2o8+ Thin Films Produced on Mgo (100) Single Crystal Substrates by Pulsed Laser Deposition (pld)(Elsevier Ltd., 2016) Nane, Onur; Özçelik, Bekir; Abukay, DoğanBi2Sr2Ca1Cu2O8+δï thin films were deposited on MgO (100) substrates by pulsed laser deposition (PLD). The effects of post-annealing time on the phase formation, the structural and superconducting properties of the films have been investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature dependent resistivity (R-T), atomic force microscopy (AFM), and DC magnetization measurements. The films deposited at 600 °C were post-annealed in an atmosphere of a gas mixture of Ar (93%) and O2 (7%), at 860 °C for 10, 30, and 60 min. All films have demonstrated a mainly single phase of 2212 with a high crystallinity (FWHM0.159°) and c-axis oriented. The critical temperature, TC, of the films annealed for 10, 30, and 60 min were obtained as 77, 78, and 78 K, respectively. The highest critical current density, JC, was calculated as 3.34×107 A/cm2 for the film annealed at 860 °C for 30 min at 10 K.Article Citation - WoS: 42Citation - Scopus: 44Growth of Cu2znsns4 Absorber Layer on Flexible Metallic Substrates for Thin Film Solar Cell Applications(Elsevier Ltd., 2015) Yazıcı, Şebnem; Olgar, Mehmet Ali; Akça, Fatime Gülşah; Cantaş, Ayten; Kurt, Metin; Aygün, Gülnur; Tarhan, Enver; Yanmaz, Ekrem; Özyüzer, LütfiIn this work, Cu2ZnSnS4 (CZTS) absorber layers were fabricated using a two-stage process. Sequentially deposited Cu-Zn-Sn thin film layers on metallic foils were annealed in an Ar + S2(g) atmosphere. We aimed to investigate the role of flexible titanium and molybdenum foil substrates in the growth mechanism of CZTS thin films. The Raman spectra and X-ray photoelectron spectroscopy analyses of the sulfurized thin films revealed that, except for the presence of Sn-based secondary phases, nearly pure CZTS thin films were obtained. Additionally, the intense and sharp X-ray diffraction peak from the (112) plane provided evidence of good crystallinity. Electron dispersive spectroscopy analysis indicated sufficient sulfur content but poor Zn atomic weight percentage in the films. Absorption and band-gap energy analyses were carried out to confirm the suitability of CZTS thin films as the absorber layer in solar cell applications. Hall effect measurements showed the p-type semiconductor behavior of the CZTS samples. Moreover, the back contact behavior of these metallic flexible substrates was investigated and compared. We detected formation of cracks in the CZTS layer on the molybdenum foils, which indicates the incompatibility of molybdenum's thermal expansion coefficient with the CZTS structure. We demonstrated the application of the magnetron sputtering technique for the fabrication of CZTS thin films on titanium foils having lightweight, flexible properties and suitable for roll-to-roll manufacturing for high throughput fabrication. Titanium foils are also cost competitive compared to molybdenum foils. © 2015 Elsevier B.V.