Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
16 results
Search Results
Article Citation - WoS: 15Citation - Scopus: 17Effects of Nanosecond Laser Ablation Parameters on Surface Modification of Carbon Fiber Reinforced Polymer Composites(SAGE Publications, 2023) Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Türkdoğan, Ceren; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemRemoval of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/?45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.Article Citation - WoS: 3Citation - Scopus: 5Deterioration of Pre-War and Rehabilitation of Post-War Urbanscapes Using Generative Adversarial Networks(SAGE Publications, 2023) Çiçek, Selen; Turhan, Gözde Damla; Taşer, AybükeThe urban built environment of contemporary cities confronts a constant risk of deterioration due to natural or artificial reasons. Especially political aggression and war conflicts have significant destructive effects on architectural and cultural heritage buildings. The post-war urbanscapes demonstrate the striking effects of the armed conflicts during the hot war encounters. However, the residues of the urbanscapes become the actual indicators of damage and loss. Since today we can make future predictions using a variety of machine learning algorithms, it is possible to represent hybrid projections of urban heterotopias. In this context, this research proposes to explore dystopian post-war projections for modern cities based on their architectural styles and demonstrate the utopian scenarios of rehabilitation possibilities for the damaged urban built environment of post-war cities by using generative adversarial network (GAN) algorithms. Two primary datasets containing the post-war and pre-war building facades have been given as the input data for the CycleGAN and pix2pix GAN models. Thus, two different image-to-image GAN models have been compared regarding their ability to produce legible building facade projections in architectural features. Besides, the machine learning process results have been discussed in terms of cities' utopian and dystopian future predictions, demonstrating the war conflicts' immense effects on the built environment. Moreover, the immediate consequence of the destructive aggression on tangible and intangible architectural heritage would become visible to inhabitants and policymakers when the AI-generated rehabilitation potentials have been exposed.Article Citation - WoS: 8Citation - Scopus: 8Improving Adhesive Behavior of Fiber Reinforced Composites by Incorporating Electrospun Polyamide-6,6 Nanofibers in Joining Region(SAGE Publications, 2022) Esenoğlu, Gözde; Barışık, Murat; Tanoğlu, Metin; Yeke, Melisa; Türkdoğan, Ceren; İplikçi, Hande; Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemAdhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 +/- 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially.Article Generating Plan Layouts: a Case Study on Visualization of Implicit Knowledge by “doctor Architects”(SAGE Publications, 2022) Kasalı, AltuğAim: This article presents an opportunistic case with particular focus on instances from an extended procurement operation in which medical professionals run a proactive process involving the generation of layouts through distinct modes of representational practices without any actual collaboration with designers. The questions of inquiry involve an analysis on how the visualizations came into being and a discussion into the content of drawings that was shaped by individuals without any formal design education. Background: Although the literature introduces examples of genuine participation, particularly in healthcare design practices, the instances in which nondesigners demonstrate accomplished skills in spatial reasoning and representation are limited. Method: The research was formulated as a qualitative case study including a series of observations of the activities of the participants followed by interviews recorded at different locations. The investigation also focuses on the features of these authentic graphics which illustrate the intentions of the medical professionals concerning the function of spaces. Results: In this research, the participants went through a labor intensive and elaborate effort to produce “architectural representations” with the intention to convey their implicit professional expertise in the domain. The layouts were introduced to be the vital elements to visualize the implicit knowledge regarding the functioning of space. Conclusions: The productive and creative engagement of clinicians within this research makes the case for a multidisciplinary approach that reframes the limits and potential contributions of participants alongside drawings, which are exclusively claimed by and strategically employed by architects as negotiation devices within participatory design processes.Article Citation - WoS: 1Citation - Scopus: 1Fatigue Life Prediction and Optimization of Gfrp Composites Based on Failure Tensor Polynomial in Fatigue Model With Exponential Fitting Approach(SAGE Publications, 2022) Güneş, Mehmet Deniz; İmamoğlu Karabaş, Neslişah; Deveci, Hamza Arda; Tanoğlu, Gamze; Tanoğlu, MetinIn this study, a new fatigue life prediction and optimization strategy utilizing the Failure Tensor Polynomial in Fatigue (FTPF) model with exponential fitting and numerical bisection method for fiber reinforced polymer composites has been proposed. Within the experimental stage, glass/epoxy composite laminates with (Formula presented.), (Formula presented.), and (Formula presented.) lay-up configurations were fabricated, quasi-static and fatigue mechanical behavior of GFRP composites was characterized to be used in the FTPF model. The prediction capability of the FTPF model was tested based on the experimental data obtained for multidirectional laminates of various composite materials. Fatigue life prediction results of the glass/epoxy laminates were found to be better as compared to those for the linear fitting predictions. The results also indicated that the approach with exponential fitting provides better fatigue life predictions as compared to those obtained by linear fitting, especially for glass/epoxy laminates. Moreover, an optimization study using the proposed methodology for fatigue life advancement of the glass/epoxy laminates was performed by a powerful hybrid algorithm, PSA/GPSA. So, two optimization scenarios including various loading configurations were considered. The optimization results exhibited that the optimized stacking sequences having maximized fatigue life can be obtained in various loading cases. It was also revealed that the tension-compression loading and the loadings involving shear loads are critical for fatigue, and further improvement in fatigue life may be achieved by designing only symmetric lay-ups instead of symmetric-balanced and diversification of fiber angles to be used in the optimization.Article Citation - WoS: 3Citation - Scopus: 3Enhancement of Filament Wound Glass Fiber/Epoxy-based Cylindrical Composites by Toughening With Single-Walled Carbon Nanotubes(SAGE Publications, 2022) Ay Solak, Zeynep; Kartav, Osman; Tanoğlu, MetinIn this study, the effect of incorporating nano-sized fillers (noncovalently functionalized with ethoxylated alcohol chemical-vapor-deposition-grown SWCNTs) within an epoxy resin on the performance of filament wound glass fiber (GF)-based cylindrical composites (GFCCs) was investigated. For this purpose, SWCNTs were dispersed with the concentration of 0.05 and 0.1 weight percent (wt.%) within an epoxy resin using mechanical stirring and calendaring (3-roll-milling) techniques. The rheological behavior of the SWCNT incorporated epoxy mixture was characterized to determine the suitability of blends for the filament winding process. It was revealed that the viscosity value of the resin was not significantly affected by the addition of SWCNTs in given concentrations. Moreover, contact angle measurements were also performed on the SWCNT/epoxy blends dropped on the GF for the evaluation of the wettability behavior of the GF in the presence of the SWCNTs in relevant concentrations. Eventually, it was observed that the wettability behavior of GF was not reasonably affected by the presence of the SWCNTs. The double cantilever beam (DCB), flexural, and short beam shear (SBS) tests were performed on the reference and SWCNT-modified GFCC specimens to evaluate the effects of the SWCNT presence on the interlaminar fracture toughness and out-of-plane properties of GFCCs. The fractured surfaces after the DCB and SBS tests were analyzed under the scanning electron microscopy to reveal the toughening mechanisms and the filler morphologies. Consequently, although SWCNT incorporation was on the outermost layer of GFCCs, it was found that the interlaminar shear strength (ILSS) values and Mode I interlaminar fracture toughness values of the curved composite samples were improved up to 22 and 216%, respectively, due to the presence of the SWCNTs.Article Citation - WoS: 14Citation - Scopus: 14Development of Biological Meniscus Scaffold: Decellularization Method and Recellularization With Meniscal Cell Population Derived From Mesenchymal Stem Cells(SAGE Publications, 2021) Kara, Aylin; Koçtürk, Semra; Bilici, Gökçen; Havıtçıoğlu, HasanTissue engineering approaches which include a combination of cells and scaffold materials provide an alternative treatment for meniscus regeneration. Decellularization and recellularization techniques are potential treatment options for transplantation. Maintenance of the ultrastructure composition of the extracellular matrix and repopulation with cells are important factors in constructing a biological scaffold and eliminating immunological reactions. The aim of the study is to develop a method to obtain biological functional meniscus scaffolds for meniscus regeneration. For this purpose, meniscus tissue was decellularized by our modified method, a combination of physical, chemical, and enzymatic methods and then recellularized with a meniscal cell population composed of fibroblasts, chondrocytes and fibrochondrocytes that obtained from mesenchymal stem cells. Decellularized and recellularized meniscus scaffolds were analysed biochemically, biomechanically and histologically. Our results revealed that cellular components of the meniscus were successfully removed by preserving collagen and GAG structures without any significant loss in biomechanical properties. Recellularization results showed that the meniscal cells were localized in the empty lacuna on the decellularized meniscus, and also well distributed and proliferated consistently during the cell culture period (p < 0.05). Furthermore, a high amount of DNA, collagen, and GAG contents (p < 0.05) were obtained with the meniscal cell population in recellularized meniscus tissue. The study demonstrates that our decellularization and recellularization methods were effective to develop a biological functional meniscus scaffold and can mimic the meniscus tissue with structural and biochemical features. We predict that the obtained biological meniscus scaffolds may provide avoidance of adverse immune reactions and an appropriate microenvironment for allogeneic or xenogeneic recipients in the transplantation process. Therefore, as a promising candidate, the obtained biological meniscus scaffolds might be verified with a transplantation experiment.Article Citation - WoS: 31Citation - Scopus: 32Development and Analysis of Composite Overwrapped Pressure Vessels for Hydrogen Storage(SAGE Publications, 2021) Kartav, Osman; Kangal, Serkan; Yücetürk, Kutay; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, composite overwrapped pressure vessels (COPVs) for high-pressure hydrogen storage were designed, modeled by finite element (FE) method, manufactured by filament winding technique and tested for burst pressure. Aluminum 6061-T6 was selected as a metallic liner material. Epoxy impregnated carbon filaments were overwrapped over the liner with a winding angle of +/- 14 degrees to obtain fully overwrapped composite reinforced vessels with non-identical front and back dome layers. The COPVs were loaded with increasing internal pressure up to the burst pressure level. During loading, deformation of the vessels was measured locally with strain gauges. The mechanical performances of COPVs designed with various number of helical, hoop and doily layers were investigated by both experimental and numerical methods. In numerical method, FE analysis containing a simple progressive damage model available in ANSYS software package for the composite section was performed. The results revealed that the FE model provides a good correlation as compared to experimental strain results for the developed COPVs. The burst pressure test results showed that integration of doily layers to the filament winding process resulted with an improvement of the COPVs performance.Article Citation - WoS: 16Citation - Scopus: 17Investigation of the High Temperature Dry Sliding Wear Behavior of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites(SAGE Publications, 2021) Martin, Seçkin; Kandemir, Sinan; Antonov, M.In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020.Article Citation - WoS: 25Citation - Scopus: 27Osteogenic Differentiation of Mesenchymal Stem Cells on Random and Aligned Pan/Ppy Nanofibrous Scaffolds(SAGE Publications, 2019) Selamet, Yusuf; İnce Yardımcı, Atike; Baskan, Öznur; Yılmaz, Selahattin; Meşe, Gülistan; Özçivici, EnginThe aim of this study was to develop random and aligned polyacrilonitrile (PAN)/polypyrrole (PPy) nanofibrous scaffolds by electrospinning technique for osteogenic differentiation of mesenchymal stem cells. Nanofibers were fabricated successfully as straight, smooth, and free from bead formation. The average diameter of random and aligned nanofibers was 268(+/- 49) nm and 225(+/- 72) nm, respectively. Alignment process increased the tensile strength of nanofibers 3.9-fold, while the tensile strain of nanofibers decreased by 78%. PAN/PPy nanofibers were hydrophilic with the contact angle value of about 32 degrees and alignment did not affect the contact angle value. Random and aligned PAN/PPy nanofibers were investigated as a scaffold material for osteogenic differentiation of D1 ORL UVA mouse bone marrow mesenchymal stem cells. Cells were able to attach and grow on nanofibers confirmed by cell viability results. Stem cells that were cultured with osteogenic induction were able to mineralize on electrospun nanofibers based on alizarin red and Von Kossa dye staining. For aligned PPy nanofibers, mineralization occurred in the fiber alignment direction. Consequently, PAN/PPy nanofibrous mats in both random and aligned forms would be potential candidates for bone tissue engineering.