Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
10 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 1Enhancing Biomass Pyrolysis via Microwave Heating: A CFD-DEM Study on Intensification in Fluidized Beds(Elsevier Sci Ltd, 2026) Hamidani, Golnaz; Kazemi, Saman; Eslami, Ali; Zarghami, Reza; Sotudeh-Gharebagh, Rahmat; Mostoufi, NavidBiomass conversion into high-value products in fluidized beds can be significantly improved by utilizing microwave irradiation as the heating source. The present work studied microwave-assisted biomass pyrolysis using a coupled CFD-DEM model in a fluidized bed. The effect of key operating parameters, including inlet gas velocity (1.5, 2, and 2.5 times the minimum fluidization velocity), mean particle diameter (1.2, 1.3, and 1.5 mm), and microwave power input (200, 400, and 600 W), was evaluated on the performance of the reactor. The results revealed that higher microwave power increased the mean particle temperature and chemical conversion rate due to greater internal energy generation within the biomass particles. Increasing the gas velocity led to lower particle temperature because of enhanced convective heat transfer to the gas phase, and improved the uniformity of temperature and conversion distributions. Furthermore, decreasing the mean particle diameter from 1.5 to 1.2 mm increased the average temperature, from 890 to 987 K, and raised biomass conversion from 14.8 to 18.1 %, mainly by reducing convective heat losses. The validated model developed in this study enables accurate predictions of process behavior and provides valuable insights for optimizing microwave-assisted biomass pyrolysis in fluidized beds. These findings highlight the potential of microwave-assisted fluidized bed pyrolysis as an efficient technique for process intensification in producing valuable bio-based products.Review Citation - Scopus: 5A Comparative Evaluation of Dark Fermentative Bioreactor Configurations for Enhanced Hydrogen Production(Springer, 2025) Gören, Ayşegül Yağmur; Dincer, I.; Khalvati, A.Energy from renewable resources has been growing in popularity, which ultimately helps reduce emissions of greenhouse gases (GHGs) and contaminants. Since hydrogen (H2) has a higher combustion production of energy than hydrocarbon fuels, it has been identified as a clean, sustainable, and environmentally friendly energy source. There are several benefits to producing biohydrogen (bioH2) from renewable sources, including lower cost and increased sustainability. Among the bioH2 production processes, dark fermentation supports commercialization and scale-up for industrial applications. This paper considers the various bioreactors, such as anaerobic sequencing batch, continuous stirred, up-flow, fixed-bed, and membrane reactors, and their operational approaches for bioH2 production. This review paper also performs the bibliometric analysis method to identify historical and current developments in a particular field of reactor configuration studies. Furthermore, the main variables influencing reactor performance and methods for increasing process efficiency considering economic and environmental aspects are addressed. The results revealed that continuously stirred reactors are widely utilized for bioH2 production as a cost-effective reactor configuration. Moreover, the membrane bioreactors and fixed-bed reactors are yielded higher bioH2 performance than other configurations. Nevertheless, high energy consumption and costs have presented the need for further development of reactors. Consequently, future recommendations to solve the critical problems faced in reactor configurations, the gaps in the literature, and the points that need improvement were comprehensively reported. © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2025.Article Citation - WoS: 6Citation - Scopus: 6A New Electro-Biomembrane Integrated Renewable-Based System To Produce Power, Fresh Water and Hydrogen for Sustainable Communities(Elsevier, 2025) Goren, A. Yagmur; Dincer, Ibrahim; Khalvati, AliAs the consequences of global warming become more severe, it is more crucial than ever to capitalize on all locally accessible potential renewable energy sources and produce sufficient useable energy outputs to meet community demands while causing the least damage to the ecosystem. Therefore, this paper focuses on a unique parabolic trough collector solar system-powered electro-biomembrane unit that combines a heat and power system with fresh water, electricity and hydrogen production. The proposed integrated system contains the following subsystems: a combining parabolic trough collector solar system, an organic Rankine cycle, a steam Rankine cycle, a multi-stage flash desalination system, and an electro-biomembrane H2 and freshwater production system. A thorough analysis and parametric research are performed on the multigeneration system to determine how important characteristics affect system performance and evaluate the energy and exergy efficiencies, and exergy destruction levels for particular system elements. The study results show that solar irradiation is the most critical parameter for improving system performance. The highest freshwater production of 1,303,333.3 L/day is observed at the solar irradiation of 935,768 kWh/day. Furthermore, the combined output of three electricity production technologies exceeds 2,000,000 kWh/day, highlighting the ability of the system to harness solar thermal energy effectively. The study findings indicate that using solar power and biomass as renewable energy sources, the proposed integrated system provided 328.56 kg of biohydrogen per day. Overall, the energy and exergy efficiencies of the integrated system are obtained as 34.3 and 29.5 %, respectively.Article Citation - WoS: 7Citation - Scopus: 7Hydrogen Production From Energetic Poplar and Waste Sludge by Electrohydrogenesis Using Membraneless Microbial Electrolysis Cells(Pergamon-elsevier Science Ltd, 2024) Goren, A. Yagmur; Kilicaslan, A. Faruk; Dincer, Ibrahim; Khalvati, AliMembraneless microbial electrolysis cells (MECs) are potentially considered to produce biohydrogen (bioH2) in a green manner and simultaneously minimize agricultural and wastewater facility wastes. However, effective, sustainable, and cost-effective system configuration and improvement of operating variables, working at ambient conditions, are needed to make the MEC a sustainable process. Therefore, this study investigates the bioH2 production from poplar leaves and anaerobic sludge mixture by incorporating nanomaterials comprising Al2O3, MgO, and Fe2O3 metal oxides at various dosages. Moreover, the effects of applied cell voltage (0.5-1.5 V) and inoculum amount (20-40 mL) on bioH2 production and organic matter removal performance are evaluated. The maximum bioH2 production value is 417 mL at an applied voltage of 1.5 V with a chemical oxygen demand (COD) removal efficiency of 37.6 % under operating times of 5 min using 40 ml of inoculum. The bioH2 production of the MEC system is reduced with the decrease in inoculum amount. The highest bioH2 production of 828 mL is obtained at improved conditions in the presence of 1 g of Fe2O3 metal oxide. Overall, this study provides the potentiality of simultaneous waste minimization and bioH2 production under ambient conditions that highlight the waste-to-energy pathway for membraneless and green bioelectrochemical process.Article Citation - WoS: 14Citation - Scopus: 17Cleaner Production of Biohydrogen Using Poplar Leaves: Experimental and Optimization Studies(Elsevier Sci Ltd, 2024) Goren, A. Yagmur; Kenez, Muratcan; Dincer, Ibrahim; Khalvati, AliBiohydrogen (bioH2) is recognized as a potential carbon-neutral energy vector, and developing novel methods has received increasing attention with a prime goal of producing H2 more efficient and cost effective manner. This study aimed to develop a unique reactor to investigate dark fermentative H2 production from poplar biomass using commercially available and inexpensive microorganism cultures. Therefore, six factors of the Box-Behnken design (BBD) were performed to evaluate the individual and combined effects of operational param-eters: acid concentration (2-10%), biomass concentration (2-10 g), initial pH (5-8), temperature (30-40 degrees C), mixing ratio (150-350 rpm), and microorganism concentration (2-6 g) on bioH2 production. Among the oper-ational parameters, the acid concentration was the most effective parameter on bioH2 production. The bioH2 production increased from 11.33 to 18.15 mg/g biomass with increasing acid concentration from 6 to 10%. Moreover, the optimum levels of operational variables were as follows: acid concentration of 9.9%, biomass amount of 2 g, pH of 6.56, temperature of 35 degrees C, mixing ratio of 345 rpm, and microorganism amount of 4.5 g for the highest bioH2 production of 20 mg/g-biomass according to the experimental design. Consequently, the bioH2 production performance of the dark fermentation process showed that bioH2 production from poplar biomass using commercially available microorganisms had a competitive advantage.Article Citation - WoS: 13Citation - Scopus: 14Perspectives of Biomass Catalytic Fast Pyrolysis for Co-Refining: Review and Correlation of Literature Data From Continuously Operated Setups(American Chemical Society, 2022) Prins, Wolter; Yıldız, GürayFor the co-processing of pyrolysis-based biocrudes within petroleum refineries, a degree of conditioning/upgrading involving the cracking of the oligomers and (partial) removal of oxygen could be operationally beneficial. By inducing a complex set of reactions in biomass-derived fast pyrolysis vapors, catalytic fast pyrolysis (CFP) ensures significant changes in oxygen functionalities and alleviates oxygen concentration in the resulting liquid intermediate (CFP-oil). Due to its reduced oxygen content and acidity, CFP-oil could be considered suitable for co-feeding in FCC units and/or for co-hydrotreatment (co-HT) with gas oils within the existing crude oil processing infrastructure. On the operational side, however, research concerning CFP of biomass has shown poor results: deoxygenation of pyrolysis vapors goes along with a progressive reduction in CFP-oil yield. Apart from any control over catalyst activity, selectivity, and lifetime, the other critical issue is in the process design, which is complicated by rapid catalyst deactivation through coke formation and catalyst poisoning by biomass-originated minerals. This review analyzes the outcome of research efforts concerning in- and ex situ CFP of biomass based on carefully selected literature studies reporting the results obtained from meso- and macrolevel laboratory-scale setups, pilot, process development units (PDU), and (semi-) commercial process units, wherein the biomass feedstock and catalyst is fed continuously. Key operational aspects such as the reactor technology, reactive medium, processing mode, and optimization of process parameters are addressed. The performances of continuously operated CFP units were benchmarked through a comparison of yields and elemental compositions of (by-)products. Despite the considerable research efforts related to CFP technology development, the co-processing of CFP-oil is still in its infancy. However, in close collaboration with refinery professionals, it could be made a serious candidate for biobased co-feeding. For refinery integration, quality parameters of CFP-oil, e.g., acidity, stability, and miscibility, should be considered as crucial as its oxygen content.Article Citation - WoS: 25Citation - Scopus: 26Phosphorylated Hazelnut Shell Waste for Sustainable Lithium Recovery Application as Biosorbent(Springer, 2021) Recepoğlu, Yaşar Kemal; Yüksel, AslıHazelnut shell waste was phosphorylated to develop a novel biosorbent based on natural renewable resource for the recovery of lithium from aqueous solution. For the synthesized biosorbent, the surface morphology and mapping by SEM-EDS, chemical properties by FTIR, elemental analysis by XPS, specific surface area by BET, crystallinity by XRD and thermal properties by TGA were elucidated elaborately. The influence of biosorbent dosage, initial concentration, temperature, contact time, pH and coexisting ions were investigated. The equilibrium sorption capacity reached 6.03 mg/g under optimal conditions (i.e., biosorbent dosage of 12.0 g/L, initial Li concentration of 100 mg/L, pH value of 5.8, sorption temperature of 25 degrees C, and sorption time of 6 min). According to the sorption behavior of the phosphorylated hazelnut shell waste the Freundlich model proved to be more suitable than the Langmuir model indicating maximum sorption capacity as 7.71 mg/g at 25 degrees C. Thermodynamic parameters obtained by different isokinetic temperatures disclosed that the ion exchange reaction was feasible, spontaneous, and exothermic where the interaction between biosorbent surface and solvent plays an important role. A preliminary test on the Li recovery from geothermal water was also performed to check its applicability in a real brine. Desorption studies at 25 degrees C revealed that relatively higher desorption efficiency and capacity were achieved at 97.4% and 5.93 mg/g, respectively with a 1.0 M H2SO4 among other regenerants (i.e., HCl and NaCl). Concentrations of Li and the other cations were determined via ICP-OES. Due to such outstanding features, the novel phosphorylated hazelnut shell waste had great potential for lithium recovery from aqueous solution by being added value as a waste and recovering a strategic element of modern life simultaneously. [GRAPHICS] .Article Citation - WoS: 31Citation - Scopus: 38Liquefaction of Waste Hazelnut Shell by Using Sub- and Supercritical Solvents as a Reaction Medium(Elsevier, 2019) Demirkaya, Emre; Dal, Orkan; Yüksel, AslıDirect thermochemical biomass degradation to obtain bio-oil by using organic solvents is not a new process type, and it has some advantages over hydrothermal liquefaction technique. However, up to our best knowledge, in this study, hazelnut shell decomposition by using ethanol, acetone and their mixtures at sub/supercritical conditions was studied for the first time in literature. Experiments were carried out between 220-300 degrees C, at three different reaction times (30, 60 and 90 min) for five different solvent ratios. Highest solid conversion achieved at 300 degrees C by using pure ethanol was 64.2%, whereas highest bio-oil yield was found as 44.2% at 300 degrees C with 50/50 (EtOH/Ac: v/v). Ethanol and acetone showed different characteristics during the reactions and their effects on the conversion and bio-oil yield were discussed. Statistical analysis showed that time, temperature, ratio and synergy between temperature-time were affecting parameters for the conversion and bio-oil yield. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 11Citation - Scopus: 12Novel Hybrid Process for the Conversion of Microcrystalline Cellulose To Value-Added Chemicals: Part 1: Process Optimization(Springer Verlag, 2016) Akın, Okan; Yüksel, AslıIn this paper, a novel hybrid process for the treatment of microcrystalline cellulose (MCC) under hot-compressed water was investigated by applying constant direct current on the reaction medium. Constant current range from 1A to 2A was applied through a cylindrical anode made of titanium to the reactor wall. Reactions were conducted using a specially designed batch reactor (450 mL) made of SUS 316 stainless steel for 30–120 min of reaction time at temperature range of 170–230 °C. As a proton donor H2SO4 was used at concentrations of 1–50 mM. Main hydrolysis products of MCC degradation in HCW were detected as glucose, fructose, levulinic acid, 5-HMF, and furfural. For the quantification of these products, High Performance Liquid Chromatography (HPLC) and Gas Chromatography with Mass Spectroscopy (GC–MS) were used. A ½ fractional factorial design with 2-level of four factors; reaction time, temperature, H2SO4 concentration and applied current with 3 center points were built and responses were statistically analyzed. Response surface methodology was used for process optimization and it was found that introduction of 1A current at 200 °C to the reaction medium increased Total Organic Carbon (TOC) and cellulose conversions to 62 and 81 %, respectively. Moreover, application of current diminished the necessary reaction temperature and time to obtain high TOC and cellulose conversion values and hence decreased the energy required for cellulose hydrolysis to value added chemicals. Applied current had diverse effect on levulinic acid concentration (29.9 %) in the liquid product (230 °C, 120 min., 2 A, 50 mM H2SO4). © 2016, Springer Science+Business Media Dordrecht.Article Citation - WoS: 34Citation - Scopus: 37Steam Gasification of Safflower Seed Cake and Catalytic Tar Decomposition Over Ceria Modified Iron Oxide Catalysts(Elsevier Ltd., 2014) Duman, Gözde; Watanabe, Taichi; Uddin, Md Azhar; Yanık, JaleCatalytic steam gasification of safflower seed cake was carried out using a double-bed microreactor in a two-stage process in the presence of ceria oxide (CeO2) modified iron oxide (Fe2O3) catalysts with different CeO2-Fe2O3 ratios. The effects of both catalyst and the temperature of catalytic bed on the tar decomposition and the overall gaseous product yield were investigated comparatively. It was found that ceria modified iron oxide catalysts had higher reactivity than that of the individual Fe2O3 and CeO2 for the catalytic tar decomposition in safflower seed cake steam gasification. The CeO2-Fe2O3 catalyst with 50 wt.% of Fe 2O3 exhibited the excellent performance for tar conversion at 700 °C. A comparison of tar decomposition from thermal run and catalytic run showed that in thermal run tar decomposition was progressed via steam reforming only. However, in the presence of catalyst, tar decomposition occurred via both steam reforming and water gas shift reaction. As a conclusion, ceria promoted iron catalysts were found to be active for both hydrogen production and tar decomposition in steam gasification of lignocellulosic biomass.