Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
16 results
Search Results
Article Citation - WoS: 13Citation - Scopus: 16Influence of Recycled Carbon Fiber Addition on the Microstructure and Creep Response of Extruded Az91 Magnesium Alloy(KeAi Communications Co., 2023) Kandemir, Sinan; Bohlen, Jan; Dieringa, HajoIn this study, the recycled short carbon fiber (CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion. The objective was to investigate the impact of CF content (2.5 and 5.0 wt.%) and fiber length (100 and 500 µm) on the microstructure, mechanical properties, and creep behavior of AZ91 alloy matrix. The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy. In comparison to the unreinforced AZ91 alloy, the composites with 2.5 wt.% CF exhibited an increase in hardness by 16–20% and yield strength by 5–15%, depending on the fiber length, while experiencing a reduction in ductility. When the reinforcement content was increased from 2.5 to 5.0 wt.%, strength values exhibited fluctuations and decline, accompanied by decreased ductility. These divergent outcomes were discussed in relation to fiber length, clustering tendency due to higher reinforcement content, and the presence of interfacial products with micro-cracks at the CF-matrix interface. Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy, suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep. © 2023Article Citation - WoS: 29Citation - Scopus: 31Effect of Heat Input on Haz Softening in Fiber Laser Welding of 22mnb5 Steel(Elsevier, 2023) Tuncel, Oğuz; Aydın, Hakan; Davut, KemalThis study investigates the effects of heat input on the heat-affected zone (HAZ) softening in fiber laser welding of quenched 1.1 mm thick 22MnB5 steel. Laser power (1500-2500 W) and welding speed (40-120 mm/s) parameters are considered as the input process variables. Depending on the input parameters, the applied heat input varied between 12.5 and 62.5 J/mm. The results indicate that a minimum heat input of 50 J/mm is required for full weld penetration. Microhardness findings revealed that the drop in hardness in the HAZ region relative to the base material (BM) reached 39% due to grain coarsening caused by an increase in heat input under the welding conditions. Grain coarsening (prior austenite grains) is also detected in SEM analysis. In addition, grain coarsening at high heat input was also determined quantitatively in EBSD analyses. The proportion of 8.91 mu m grain size in the sample with high heat input is 4.2%, while it is 1.2% in the sample with low heat input. When the heat input increased from 12.5 to 62.5 J/mm, the width of the softened zone with the lowest hardnesses in the HAZ grew from 0.2 mm to 2.2 mm.Article Citation - WoS: 39Citation - Scopus: 41Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier, 2022) Özer, Seren; Bilgin, Güney Mert; Davut, Kemal; Esen, Ziya; Dericioğlu, Arcan.FThe effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples disappeared and converted into a mixture of columnar and equiaxed grains. Nano-sized γ″ and/or γ′ precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 °C for 8 h) tested at 600 °C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700–800 °C, which was attributed to intermediate temperature embrittlement.Article Citation - WoS: 41Citation - Scopus: 45High Temperature Tensile, Compression and Creep Behavior of Recycled Short Carbon Fibre Reinforced Az91 Magnesium Alloy Fabricated by a High Shearing Dispersion Technique(National Engineering Research Center for Magnesium Alloys of China, Chongqing University, 2021) Kandemir, Sinan; Gavras, Sarkis; Dieringa, HajoThe present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 ?m) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021Article Citation - WoS: 187Citation - Scopus: 266Improvement of Barrier and Mechanical Properties of Whey Protein Isolate Based Food Packaging Films by Incorporation of Zein Nanoparticles as a Novel Bionanocomposite(Elsevier Ltd., 2016) Oymacı, Pelin; Alsoy Altınkaya, SacideIn this study, whey protein isolate (WPI) based bio-nanocomposite films embedded with zein nanoparticles (ZNP) were prepared by solution casting. Nanoparticles were coated with sodium caseinate to obtain a uniform distribution in the films. The mechanical, water vapor barrier, surface wetting, morphological and viscoelastic properties of the films were investigated. The addition of ZNP significantly improved the water vapor barrier and mechanical properties of the WPI without adversely affecting the elongation of the films. Dynamical mechanical analysis and contact angle measurements revealed that upon addition of the nanoparticles, the fractional free volume and hydrophilicity of the WPI films decreased. Sodium caseinate containing both hydrophilic and hydrophobic groups created an efficient interface between the hydrophobic ZNP and hydrophilic WPI matrix, allowing for a homogeneous distribution of nanoparticles even at very high loading levels as evidenced by the scanning electron microscope (SEM) and atomic force microscopy (AFM) images. The WPI/ZNP nanocomposite films can potentially become effective food packaging materials.Article Citation - WoS: 62Citation - Scopus: 75Specimen Size Effect on the Residual Properties of Engineered Cementitious Composites Subjected To High Temperatures(Elsevier Ltd., 2014) Erdem, Tahir KemalIn this study, size effect on the residual properties of Engineered Cementitious Composites (ECC) was investigated on the specimens exposed to high temperatures up to 800 C. Cylindrical specimens having different sizes were produced with a standard ECC mixture. Changes in pore structure, residual compressive strength and stress-strain curves due to high temperatures were determined after air cooling. Experimental results indicate that despite the increase of specimen size, no explosive spalling occurred in any of the specimens during the high temperature exposure. Increasing the specimen size and exposure temperature decreased the compressive strength and stiffness. Percent reduction in compressive strength and stiffness due to high temperature was similar for all specimen sizes.Article Citation - WoS: 77Citation - Scopus: 93Improving the Workability and Rheological Properties of Engineered Cementitious Composites Using Factorial Experimental Design(Elsevier Ltd., 2013) Şahmaran, Mustafa; Bilici, Zafer; Özbay, Erdoğan; Erdem, Tahir Kemal; Yücel, Hasan Erhan; Lachemi, MohamedIn the development of Engineered Cementitious Composites (ECC), micromechanics-based design theory is adopted to properly select the matrix constituents, fiber, and fiber-matrix interface properties to exhibit strain hardening and multiple cracking behaviors. Despite the micromechanics design constraints, practical applications show that the workability and rheological properties of matrix can affect the fiber dispersion uniformity, which have also direct concerns on composite mechanical properties. For this reason, in this research, parameters of micromechanics-based optimized ECC mixture design, which most possibly affecting the workability and rheological properties, are investigated. An experimental program that contains 36 different ECC mixtures was undertaken to quantitatively evaluate the combined effects of the following factors on workability and rheological properties: water-binder (w/b), sand-binder (s/b), superplasticizer-binder (SP/b) ratios and maximum aggregate size (Dmax). A mini-slump cone, a Marsh cone and a rotational viscometer were used to evaluate the workability and rheological properties of ECC mixtures. Compressive strength and four point bending tests were used for mechanical characteristics of ECC mixtures at 28 days. The effects of studied parameters (w/b, s/b, SP/b and Dmax) were characterized and analyzed using regression models, which can identify the primary factors and their interactions on the measured properties. Statistically significant regression models were developed for all tested parameters as function of w/b, s/b, SP/b and Dmax. To find out the best possible ECC mixture under the range of parameters investigated for the desired workability and mechanical characteristics, a multi-objective optimization problem was defined and solved based on the developed regression models. Test results indicate that w/b, s/b and SP/b parameters affect the rheological and workability properties. On the other hand, for the range of studied aggregate sizes, Dmax is found to be statistically insignificant on the rheological and workability properties of ECC.Article Citation - WoS: 33Citation - Scopus: 41Development of Novel Multilayer Materials for Impact Applications: a Combined Numerical and Experimental Approach(Elsevier Ltd., 2009) Taşdemirci, Alper; Hall, Ian W.A well-verified and validated numerical model was used to investigate stress wave propagation in a multilayer material subjected to impact loading. The baseline material consisted of a ceramic faceplate and composite backing plate separated by a rubber or teflon foam interlayer: several variants were investigated in which the number, type, and total thicknesses of the interlayers were altered. Comparison of the variants showed that the use of multiple teflon foam interlayers could drastically reduce the average stress in the multilayer material. Based on the numerical results, further experimental work was undertaken upon one of the variants. Very large and unexpected tensile stress oscillations were observed in the ceramic layers, leading to a refinement of the numerical model which successfully reproduced the oscillations and also demonstrated that separation of the sample layers led to trapping of the stress wave within the layers. Use of the validated numerical model allowed detailed analysis of the processes of wave transmission and demonstrates the important synergy that can exist between experimental and modeling studies. The current study provides a valuable starting point for designing future multilayer materials with specific, controlled properties.Article Citation - WoS: 78Citation - Scopus: 106Critical Aspects Related To Processing of Carbon Nanotube/Unsaturated Thermoset Polyester Nanocomposites(Elsevier Ltd., 2007) Seyhan, Abdullah Tuğrul; Gojny, Florian H.; Tanoğlu, Metin; Schulte, KarlCarbon nanotubes (CNTs) have outstanding mechanical, thermal and electrical properties. As a result, particular interest has been recently given in exploiting these properties by incorporating carbon nanotubes into some form of matrix. Although unsaturated polyesters with styrene have widespread use in the industrial applications, surprisingly there is no study in the literature about CNT/thermoset polyester nanocomposite systems. In the present paper, we underline some important issues and limitations during the processing of unsaturated polyester resins with different types of carbon nanotubes. In that manner, 3-roll mill and sonication techniques were comparatively evaluated to process nanocomposites made of CNTs with and without amine (NH2) functional groups and polyesters. It was found that styrene evaporation from the polyester resin system was a critical issue for nanocomposite processing. Rheological behaviour of the suspensions containing CNTs and tensile strengths of their resulting nanocomposites were characterized. CNT/polyester suspensions exhibited a shear thinning behaviour, while polyester resin blends act as a Newtonian fluid. It was also found that nanotubes with amine functional groups have better tensile strength, as compared to those with untreated CNTs. Transmission electron microscopy (TEM) was also employed to reveal the degree of dispersion of CNTs in the matrix.Article Citation - WoS: 71Citation - Scopus: 87Influence of Surface Modification of Fillers and Polymer on Flammability and Tensile Behaviour of Polypropylene-Composites(Elsevier Ltd., 2006) Demir, Hasan; Balköse, Devrim; Ülkü, SemraAn intumescent system consisting of ammonium polyphosphate (APP) as an acid source and blowing agent, pentaerythritol (PER) as a carbonific agent and natural zeolite (clinoptilolite, Gördes II) as a synergistic agent was used in this study to enhance flame retardancy of polypropylene (FR-PP). Zeolite was incorporated into flame retardant formulation at four different concentrations (1, 2, 5, and 10 wt%) to investigate synergism with the flame retardant materials. Filler content was fixed at 30 wt% of total amounts of flame retardant PP composites. Zeolite and APP were treated with two different coupling agents namely, 3-(trimethoxysilyl)-1-propanethiol and (3-aminopropyl)-triethoxysilane for investigation of the influence of surface treatments on mechanical properties and flame retardant performance of composites. Maleic anhydride grafted polypropylene (MAPP) was used for making polypropylene hydrophilic. Flammability of FR-PP composites was measured by the determination of limiting oxygen index (LOI). The LOI values reached to a maximum value of 41% for mercapto silane treated APP:PER (2:1) PP composite containing 5 wt% zeolite. The tensile strength of composites was increased by the addition of MAPP and elongation at break of composites was increased with silane treatments.