Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
5 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 2Citation - Scopus: 1Dynamics of Co2 Consumption, and Biomass and Lipid Carbon Production During Photobioreactor Cultivation of the Diatom Cyclotella(TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2023) Ökten, HaticeUnderstanding of CO2 delivery and consumption dynamics in algal photobioreactors are critical to unravel microalgae’s full potential for bioproduct generation and carbon capture from flue gas streams. This study aims to expand our current understanding by cultivating the diatom Cyclotella under controlled process conditions of a bubble column photobioreactor and analyzing CO2 consumption dynamics in real time using results from an online CO2 sensor connected to the reactor exhaust. Two sets of experiments were conducted: they served to contrast the influence of silicon and nitrate (Si&N colimitation) and Si limitation, and the light availability, respectively. CO2 consumption was calculated based on the mass balance around the reactor inlet and outlet gas streams. Biomass samples and lipid extracts were analyzed for carbon (C) content to determine biomass-C and lipid-C concentrations. The outlet CO2 concentrations varied significantly with cultivation time and process conditions. More than 15% to 65% of the CO2 introduced left the reactor in the exhaust at any instance based on the set CO2 transfer rates. The highest average daily capturing efficiency was 60%. Nutrient limitation regimes imposed generated unique CO2 consumption profiles undiscernible by the biomass-C analysis, i.e. unlike Si limitation, N limitation had more immediate detrimental effects on C consumption. Final biomass-C concentration increased with increasing N and light availability, 275 mg/L vs. 336 mg/L, and 270 mg/L vs. 501 mg/L, respectively. Biomass-C based capturing efficiency approximations resulted in 20% to 40% underestimation. Under Si-limited conditions, the higher light intensity increased the final lipid-C to biomass-C ratio by two times (from 20% to 40%) and the final lipid-C concentration and peak productivity by four times (from 56 mg/L to 216 mg/L, from 7 to 30 mg/L-day, respectively). This study demonstrates online exhaust CO2 concentration-based analysis’s unique capabilities for assessing carbon availability and capture, organic-C production, and its diversion to biomass and lipid production.Article Citation - WoS: 2Citation - Scopus: 2Evaluating the Performance of Conventional Daf and Posidaf Processes for Cyanobacteria Separation at a Pilot Plant Scale(IWA Publishing, 2022) Yap, Russell K.L.; Rao, N. R.H.; Holmes, M.; Whittaker, Michael; Stuetz, Richard M.; Jefferson, Bruce; Bulmuş, Volga; Peirson, William Leslie; Henderson, R. K.In this work, a commercially available water treatment polymer poly(N,N-diallyl-N,N-dimethylammonium chloride) (PDADMAC) and a hydrophobically modified polymer (HMP) designed to adhere to bubble surfaces were applied for the first time in the novel Posi-dissolved air flotation process (PosiDAF) that uses polymer-modified bubbles, at pilot-scale for the treatment of waste stabilisation pond samples rich in algae. It was found that PDADMAC in PosiDAF gave comparable removal to that achieved using conventional DAF at .95% cell separation. Furthermore, the float layer was more uniform and thicker with up to 8% solid contents compared to conventional DAF, which comprised discrete floc clusters with an average solid concentration of ∼4.1%. In contrast to the use of PDADMAC, the application of the HMP did not achieve similarly good separation at pilot scale. It was hypothesised that this may be due to the micellisation of the HMP on the bubble surface, creating unstable bubbles that coalesced and prevented polymer-bubble-cell interactions, which are crucial for effective cell separation. On comparison of the costs of PosiDAF and conventional DAF, it was found that PosiDAF resulted in cost-savings of up to 74% due to low chemical consumption. In summary, PosiDAF reduced chemical cost and increased solid contents in the metal-free float.Article Citation - WoS: 61Citation - Scopus: 75Optimization of Biomass, Pellet Size and Polygalacturonase Production by Aspergillus Sojae Atcc 20235 Using Response Surface Methodology(Elsevier Ltd., 2007) Tarı, Canan; Göğüş, Nihan; Tokatlı, FigenA two-step optimization procedure using central composite design with four factors (concentrations of maltrin and corn steep liquor (CSL), agitation speed and inoculation ratio) was used in order to investigate the effect of these parameters on the polygalacturonase (PG) enzyme activity, mycelia growth (biomass) and morphology (pellet size) of Aspergillus sojae ATCC 20235. According to the results of response surface methodology (RSM), initial concentrations of maltrin and CSL and agitation speed were significant (p < 0.05) on both PG enzyme production and biomass formation. As a result of this optimization, maximum PG activity (13.5 U/ml) was achievable at high maltrin (120 g/l), at low CSL (0 g/l), high agitation speed (350 rpm) and high inoculation ratio (2 × 107 total spore). Similarly, maximum biomass (26 g/l) could be obtained under the same conditions with only the difference for higher level of CSL requirement. The diameter of pellets in all optimization experiments ranged between 0.05 and 0.76 cm. The second optimization step improved the PG activity by 74% and the biomass by 40%.Article Citation - WoS: 30Citation - Scopus: 42Effect of Various Process Parameters on Morphology, Rheology, and Polygalacturonase Production by Aspergillus Sojae in a Batch Bioreactor(American Institute of Chemical Engineers, 2007) Öncü, Şelale; Tarı, Canan; Ünlütürk, SevcanThe effects of pH, agitation speed, and dissolved oxygen tension (DOT), significant in common fungal fermentations, on the production of polygalacturonase (PG) enzyme and their relation to morphology and broth rheology were investigated using Aspergillus sojae in a batch bioreactor. All three factors were effective on the response parameters under study. An uncontrolled pH increased biomass and PG activity by 27% and 38%, respectively, compared to controlled pH (pH 6) with an average pellet size of 1.69 ± 0.48 mm. pH did not significantly affect the broth rheology but created an impact on the pellet morphology. Similarly, at constant agitation speed the maximum biomass obtained at 500 rpm and at 30 h was 3.27 and 3.67 times more than at 200 and 350 rpm, respectively, with an average pellet size of 1.08 ± 0.42 mm. The maximum enzyme productivity of 0.149 U mL-1 h-1 was obtained at 200 rpm with an average pellet size of 0.71 ± 0.35 mm. Non-Newtonian and pseudoplastic broth rheology was observed at 500 rpm agitation speed, broth rheology exhibited dilatant behavior at the lower agitation rate (200 rpm), and at the medium agitation speed (350 rpm) the broth was close to Newtonian. Furthermore, a DOT range of 30-50% was essential for maximum biomass formation, whereas only 10% DOT was required for maximum PG synthesis. Non-Newtonian shear thickening behavior (n > 1.0) was depicted at DOT levels of 10% and 30%, whereas non-Newtonian shear thinning behavior (n < 1.0) was dominant at 50% DOT. The overall fermentation duration (50-70 h) was considerably shorter compared to common fungal fermentations, revealing the economic feasibility of this particular process. As a result this study not only introduced a new strain with a potential of producing a highly commercially significant enzyme but also provided certain parameters significant in the design and mathematical modeling of fungal bioprocesses.