Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Citation - WoS: 20Citation - Scopus: 22Fabrication and Properties of Novel Porous Ceramic Membrane Supports From the (sig) Diatomite and Alumina Mixtures(Elsevier, 2022) Aouadja, Faycal; Bouzerara, Ferhat; Güvenç, Çetin Meriç; Demir, Mustafa M.In this paper, the manufacturing of macro-porous tubular ceramic supports for membranes is described. The novel supports are fabricated from natural diatomite and alumina raw materials using the extrusion method. The structure was analyzed by X-ray diffraction (XRD) and mercury porosimetry techniques; the presence of possible defects was investigated by scanning electron microscopy (SEM). The permeability has been measured from water flux in standard experiments. Experimental results show that the open porosity, the average pore size (APS), the pore size distribution, the strength, and the permeability of sintered supports, have been found to depend, mainly on the concentration of alumina (Al2O3) additive. Supports prepared with the addition of 10 wt.% of alumina and sintered at 1200 degrees C, can be considered as the most optimized; they have a porosity ratio of about 46%, an APS is around 7.7 mu m, a flexural strength value of about 28 MPa, and water permeability of around 15 m(3)h(-1) m(-2) bar(-1). Such materials could be of great interest in the supports fabrication for membrane application, for instance, water filtration. (C) 2021 SECV. Published by Elsevier Espana, S.L.U.Conference Object Citation - WoS: 21Citation - Scopus: 26Investigation of Long Waviness Induced by the Wire Saw Process(SAGE Publications Inc., 2011) Teomete, EgemenIn the photovoltaic and semiconductor industries silicon wafers are sliced using the wire saw process. This process is also used to machine almost all kinds of brittle materials where high yield and low surface damage is desired. The wire saw process induces roughness and long waviness on the cut surface. These defects have to be removed by post-process techniques including grinding and lapping, which increases costs. The present study investigated the long waviness induced by the wire saw process. An analytical model for long waviness generation has been developed. Experimental work was conducted with different process parameters. The analytical model is capable of explaining the long waviness generation observed in experimental work. Process design recommendations with minimal waviness and high efficiency are presented.Article Citation - WoS: 67Citation - Scopus: 82Microhardness and Fracture Toughness of Dental Materials by Indentation Method(John Wiley and Sons Inc., 2005) Şakar-Deliormanlı, Aylin; Şakar Deliormanlı, Aylin Müyesser; Güden, Mustafa; Güden, MustafaThe main objective of this study was to measure the fracture toughness of the human teeth enamel using the microindentation technique and to compare the results calculated from the equations developed for Palmqvist and radial-median cracks. Vickers microhardness measurements of dental ceramic (alumina) and human teeth were performed using indentation fracture method. The fracture toughness of enamel was calculated using different equations reported in the literature. Vickers microhardness of the sintered alumina specimen (98.8% theoretical density) was measured to be 14.92 GPa under 9.8N indentation load. Three equations based on the radial-median cracks were found to be applicable for the fracture toughness determination of the enamel. Results show that indentation fracture method is adequate to measure microhardness and fracture toughness of dental materials. However the calculation of fracture toughness depended on the nature of the cracks and also on the location of the indentation. Therefore, it is necessary to identify the crack profile and to select the appropriate equation for accurate fracture toughness values.