Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
4 results
Search Results
Article Citation - WoS: 8Citation - Scopus: 8Study of Boron Doped Amorphous Silicon Lightly Hydrogenated Prepared by Dc Magnetron Sputtering for Infrared Detectors Applications(Elsevier Ltd., 2020) Ketroussi, K.; Cherfi, R.; Yahia, Seba, H.; Tata, S.; Chabane, L.; Özyüzer, Lütfi; Rahal, A.The objective of this study is to investigate the effect of boron doping concentration on the bolometric properties of lightly hydrogenated amorphous silicon doped with boron (a-Si: H(B)) films. Thin film a-Si: H(B) samples with different boron concentrations are prepared by co-sputtering of boron and silicon at relatively low hydrogen pressure. FTIR analyses show that the intensity of the characteristic peak of the substitutional boron gradually increases with the addition of boron. Increasing in boron concentration affects the bolometric properties of the lightly hydrogenated a-Si: H (B) films, including conductivity at room temperature (?RT) and thermal resistance coefficient (TCR). Indeed, when the boron concentration increases from 1.5 to 43%, ?RT increases from 1.4 10?6 to 2 10?3 ??1 cm?1 while the absolute value of TCR decreases from 3% to 8% K?1, respectively. In addition, lightly hydrogenated a-Si: H (B) films exhibit good thermal stability. We have showed in this study that lightly hydrogenated a-Si: H(B) can be considered as a potential candidate for low-cost, high-performance uncooled micro bolometers. © 2020 Elsevier B.V.Article Citation - WoS: 11Citation - Scopus: 12Electrical Properties of Gadolinia Doped Ceria Electrolytes Fabricated by Infiltration Aided Sintering(Elsevier Ltd., 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatCommon solid oxide fuel cell (SOFC) electrolyte materials (e.g., gadolinia doped ceria - GDC) demand temperatures exceeding 1400 degrees C for densification by conventional solid state sintering. It is very desirable to reduce the densification of the SOFC electroltytes to i) avoid microstructural coarsening of the composite anode layers, which are co-sintered with the electolyte layer in the anode supported SOFC fabrication scheme and ii) reduce energy consumption during SOFC manufacturing. We have recently demostrated a novel infiltration-aided sintering route to densify GDC ceramics at 1200 degrees C. In the present work, we present the electrical properties of GDC ceramics fabricated thusly. Comparison of high density (>= 95%) samples fabricated by conventional or infiltration-aided sintering reveal that at 700 degrees C, similar total electrical conductivities are obtained, while at 300 degrees C, specific grain boundary resistivity is smaller in the latter. Bulk (grain) conductivity is higher in porous GDC ceramics (relative density <= 90%) fabricated by infiltration-aided sintering than the conventionally sintered ones with similar porosities. Finally, open circuit voltage of 0.84 V at 700 degrees C, obtained under dilute hydrogen and stagnant air conditions suggests that GDC ceramics densified by infiltration-aided sintering are suitable for use as SOFC electrolytes.Article Citation - WoS: 6Citation - Scopus: 9Preparation and Characterization of Flexible Polyvinylchloride-Copper Composite Films(Smithers Rapra Technology, 2013) Kurt, Emrah; Özçelik, Cenk Yağız; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimFlexible PVC films are statically charged due to their low electrical conductivity. This creates fire threat during its handling. Conductive materials are added to films to prevent this. In the present study it was aimed to prepare PVC- copper composite films by sol gel technique and characterize the prepared films. It was aimed to increase the electrical conductivity of the films by adding copper powder. However, the copper particles settled down to bottom instead of forming a conductive network that covers the whole cross section. Thus at the film crosssection a plastic upper phase and a copper rich lower phase were present. The film did not conduct electricity due to this uneven distribution. The minimum volumetric and surface resistivities of the films were at the order of 109 ohm-cm and 1010 ohm square respectively.Article Citation - WoS: 114Citation - Scopus: 135Perspectives for Solid Biopolymer Electrolytes in Dye Sensitized Solar Cell and Battery Application(Elsevier Ltd., 2016) Singh, Rahul; Polu, Anji Reddy; Bhattacharya, B.; Rhee, Hee-Woo; Varlıklı, Canan; Singh, Pramod K.Photovoltaic technologies represent one of the leading research areas of solar energy which is one of the most powerful renewable alternatives of fossil fuels. In a common photovoltaic application the batteries play a key role in storage of energy generated by solar panels. Although it will take time for dye sensitized solar cells (DSSCs) and batteries based on biopolymer electrolytes to take their places in the market, laboratory studies prove that they have a lot to offer. Most efficient DSSCs and batteries available in market are based on liquid electrolytes. The advantages of liquid electrolytes are having high conductivity and good electrode-electrolyte interface whereas, disadvantages like corrosion and evaporation limit their future sustainability. Biopolymer electrolytes are proposed as novel alternatives which may overcome the problems stated above. In this review, we focus on fabrication, working principle as well as up to date status of DSSCs and batteries using biopolymer electrolytes. The effects of structural and electrical properties of biopolymer based electrolytes on the solar energy conversion efficiencies of DSSCs and their compatibility with lithium or other salts in battery applications are summarized. Biopolymer electrolyte based DSSCs are categorized on the basis of types of additives and recent outcomes of author's laboratory studies on biopolymer electrolyte based DSSCs and batteries are also presented.