Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Citation - WoS: 19Citation - Scopus: 20Isothermal Crystallization Kinetics and Mechanical Properties of Polycaprolactone Composites With Zinc Oxide, Oleic Acid, and Glycerol Monooleate(John Wiley and Sons Inc., 2013) Alp, Burcu; Cesur, SerapThe isothermal crystallization and mechanical behavior of polycaprolactone (PCL) with zinc oxide (ZnO) with oleic acid and glycerol monooleate (GMO) were studied. Theoretical melting points calculated by the Flory-Huggins and Thompson-Gibbs models were thoroughly compared with differential scanning calorimetry experimental observations. The isothermal crystallization kinetic parameters by Avrami analysis showed that crystallization was controlled by nucleation, crystal growth was spherical, and the nucleation type changed between thermal and athermal nucleation. X-ray diffraction showed that when the additives were used together both the crystal thickness and the degree of crystallinity increased. A multiple-response regression analysis was made with the ZnO, oleic acid, and GMO concentrations as variables and the crystallinity as output. Interaction parameters by the Pukanzky model were calculated from the tensile strength at the yield point and indicated that the addition of oleic acid or GMO improved the interface between the ZnO particles and PCL.Article Citation - WoS: 25Citation - Scopus: 26Structural and Optical Characteristics of Tantalum Oxide Grown by Pulsed Nd:yag Laser Oxidation(AVS Science and Technology Society, 2006) Atanassova, Elenada A.; Aygün, Gülnur; Turan, Raşit; Babeva, T.Tantalum pentoxide (Ta2 O5) thin films (20-50 nm) have been grown by 1064 nm Nd:YAG laser oxidation of Ta film deposited on Si. The chemical bonding, structure, and optical properties of the films have been studied by Fourier transform infrared spectroscopy, x-ray diffraction, and reflectance measurements at normal light incidence in the spectral range of 350-800 nm. The effect of the substrate temperature (250-400 °C) during oxidation and its optimization with respect to the used laser beam energy density (3.2-3.4 J cm2 per pulse) is discussed. It is established that the substrate temperature is a critical factor for the effectiveness of the oxidation process and can be used to control the composition and amorphous status of the films. The film density explored by refractive index is improved with increasing film thickness. The refractive index of the layers grown under the higher laser beam energy density and at substrate temperature of 350-400 °C was found to be close to the value of bulk Ta2 O5. The films are amorphous at substrate temperature below 350 °C and possessed an orthorhombic (Β- Ta2 O5) crystal structure at higher temperatures. The thinner layers crystallize at a little higher temperature.Article Citation - WoS: 42Citation - Scopus: 42Natural Zeolite Polypropylene Composite Film Preparation and Characterization(John Wiley and Sons Inc., 2001) Özmıhçı, Filiz; Balköse, Devrim; Ülkü, SemraIn this research, the preparation and characterization of polypropylene (PP) and natural zeolite composites were studied. Natural zeolite mined in Gördes, Turkey was used as an alternative filler to CaCO3. Films were prepared by the extrusion of PP, and surface-modified zeolite was made by polyethylene glycol 4000 with 2-4% zeolite. Zeolite-filled composites had densities between 0.73 and 0.83 g/cm3 and had void fractions of 0.07-0.20. Although the permeability of water vapour through 2% zeolite-filled composites was very small, 4% zeolite-filled films had very high permeabilities. The yield stresses of 2-4% zeolite-containing films were around 26-27 N/mm2 and were lower than that of PP, which indicated no adhesion between PP and zeolite. The effect of zeolite on the thermal degradation behaviour in air and in a N2 atmosphere was also studied. In air, zeolites did not cause the oxidation of PP. In a N2 atmosphere, although the start of the thermal degradation of PP was retarded by zeolite, composites degraded at a faster rate than PP once the degradation started. At a processing temperature of 200°C, zeolites had no effect on the degradation of PP.