Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
5 results
Search Results
Article Citation - WoS: 20Citation - Scopus: 22Fabrication and Properties of Novel Porous Ceramic Membrane Supports From the (sig) Diatomite and Alumina Mixtures(Elsevier, 2022) Aouadja, Faycal; Bouzerara, Ferhat; Güvenç, Çetin Meriç; Demir, Mustafa M.In this paper, the manufacturing of macro-porous tubular ceramic supports for membranes is described. The novel supports are fabricated from natural diatomite and alumina raw materials using the extrusion method. The structure was analyzed by X-ray diffraction (XRD) and mercury porosimetry techniques; the presence of possible defects was investigated by scanning electron microscopy (SEM). The permeability has been measured from water flux in standard experiments. Experimental results show that the open porosity, the average pore size (APS), the pore size distribution, the strength, and the permeability of sintered supports, have been found to depend, mainly on the concentration of alumina (Al2O3) additive. Supports prepared with the addition of 10 wt.% of alumina and sintered at 1200 degrees C, can be considered as the most optimized; they have a porosity ratio of about 46%, an APS is around 7.7 mu m, a flexural strength value of about 28 MPa, and water permeability of around 15 m(3)h(-1) m(-2) bar(-1). Such materials could be of great interest in the supports fabrication for membrane application, for instance, water filtration. (C) 2021 SECV. Published by Elsevier Espana, S.L.U.Article Citation - WoS: 43Citation - Scopus: 47Bioactive Diatomite and Poss Silica Cage Reinforced Chitosan/Na-carboxymethyl Cellulose Polyelectrolyte Scaffolds for Hard Tissue Regeneration(Elsevier, 2019) Tamburacı, Sedef; Kimna, Ceren; Tıhmınlıoğlu, FundaRecently, natural polymers are reinforced with silica particles for hard tissue engineering applications to induce bone regeneration. In this study, as two novel bioactive agents, effects of diatomite and polyhedral oligomeric silsesquioxanes (POSS) on chitosan (CS)/Na-carboxymethylcellulose (Na-CMC) polymer blend scaffolds are examined. In addition, the effect of silica reinforcements was compared with Si-substituted nano-hydroxyapatite (Si-Hap) particles. The morphology, physical and chemical structures of the scaffolds were characterized with SEM, liquid displacement, FT-IR, mechanical analysis, swelling and degradation studies. The particle size and the crystal structure of diatomite, POSS and Si-Hap particles were determined with DLS and XRD analyses. In vitro studies were performed to figure out the cytotoxicity, proliferation, ALP activity, osteocalcin production and biomineralization to demonstrate the promising use of natural silica particles in bone regeneration. Freeze-dried scaffolds showed 190-307 mu m pore size range and 61-70% porosity. Both inorganic reinforcements increased the mechanical strength, enhanced the water uptake capacity and fastened the degradation rate. The nanocomposite scaffolds did not show any cytotoxic effect and enhanced the surface mineralization in osteogenic medium. Thus, diatomite and POSS cage structures can be potential reinforcements for nanocomposite design in hard tissue engineering applications.Article Citation - WoS: 51Citation - Scopus: 60Biosilica Incorporated 3d Porous Scaffolds for Bone Tissue Engineering Applications(Elsevier Ltd., 2018) Tamburacı, Sedef; Tıhmınlıoğlu, FundaAs a natural and abundant silica mineral, diatomite particles (SiO2-nH2O) have been used in several areas such as filtration, photonics, sound and heat insulation, filler material and drug delivery due to its abundance, inexpensive cost, unique morphology and porous structure. But up to date, diatomite incorporated silica based scaffolds have not been used for bone tissue engineering applications. In the present study, the goal was to combine the useful biomaterial properties of both chitosan and diatomite as biocomposite organic/inorganic biomaterial for bone tissue engineering applications and optimize the silica content of the composites in order to obtain optimum morphological structure, high mechanical properties, enlarged surface area and enhanced cell proliferation. The effect of silica loading on the mechanical, morphological, chemical, and surface properties, wettability and biocompatibility of composite scaffolds were investigated. In addition, in vitro cytotoxicity and cellular activities including cell proliferation, ALP activity and biomineralization were investigated in order to determine biological activity of the composite scaffolds. Diatomite particles lead to enhancement in the water uptake capacity of scaffolds. Chitosan-silica composites exhibited 82–90% porosity. Wet chitosan-silica composite scaffolds exhibited higher compression moduli when compared to pure chitosan scaffold in the range of 67.3–90.1 kPa. Average pore size range of chitosan-diatomite composite scaffolds was obtained as 218-319 μm. In vitro results indicated that chitosan-diatomite composites did not show any cytotoxic effect on 3T3, MG-63 and Saos-2 cell lines. Scaffolds were found to be favorable for osteoblast proliferation. Diatomite incorporation showed promising effects on enhancing ALP activity as well as mineral formation on scaffold surface. Thus, the prepared scaffolds in this study can be considered prospective material for bone tissue engineering applications.Article Citation - WoS: 62Citation - Scopus: 72Diatomite Reinforced Chitosan Composite Membrane as Potential Scaffold for Guided Bone Regeneration(Elsevier Ltd., 2017) Tamburacı, Sedef; Tıhmınlıoğlu, FundaIn this study, natural silica source, diatomite, incorporated novel chitosan based composite membranes were fabricated and characterized for bone tissue engineering applications as possible bone regeneration membrane. The effect of diatomite loading on the mechanical, morphological, chemical, thermal and surface properties, wettability and in vitro cytotoxicity and cell proliferation on of composite membranes were investigated and observed by tensile test, atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), protein adsorption assay, air/water contact angle analysis and WST-1 respectively. Swelling studies were also performed by water absorption capacity determination. Results showed that incorporation of diatomite to the chitosan matrix increased the surface roughness, swelling capacity and tensile modulus of membranes. An increase of about 52% in Young's modulus was achieved for 10 wt% diatomite composite membranes compared with chitosan membranes. High cell viability results were obtained with indirect extraction method. Besides, in vitro cell proliferation and ALP activity results showed that diatom incorporation significantly increased the ALP activity of Saos-2 cells cultured on chitosan membranes. The novel composite membranes prepared in the present study with tunable properties can be considered as a potential candidate as a scaffold in view of its enhanced physical & chemical properties as well as biological activities for bone tissue engineering applications.Article Citation - WoS: 8Citation - Scopus: 9The Increased Compression Strength of an Epoxy Resin With the Addition of Heat-Treated Natural Nano-Structured Diatom Frustules(SAGE Publications Inc., 2017) Zeren, Doğuş; Güden, MustafaNatural diatom frustules composing nanometer size silica particles were heat-treated at temperatures between 600 and 1200℃ for 2 h and used as filler/reinforcing agent (15 wt%) in an epoxy resin. The opal structure of as-received natural diatom frustules was transformed into cristobalite after the heat-treatment above 900℃. The epoxy resin test samples reinforced with heat-treated and as-received frustules and neat epoxy test samples were compression tested at the quasi-static strain rate of 7 × 10−3 s−1. The results showed that the inclusion of the frustules heat-treated at 1000℃ increased the compressive yield strength of the resin by 50%, while the addition of the diatom frustules heat-treated above and below 1000℃ and the as-received frustules increased the strength by ∼25% and 16%, respectively. The heat treatment above 1000℃ decreased the surface area of the frustules from 8.23 m2 g−1 to 3.46 m2 g−1. The cristobalite grains of the frustules heat-treated at 1000℃ was smaller than 100 nm, while the grain size increased to ∼500 nm at 1200℃. The increased compressive stresses of the resin at the specific heat treatment temperature (1000℃) were ascribed to nano size crystalline cristobalite grains. The relatively lower compressive stresses of the epoxy resin filled with frustules heat-treated above 1000℃ were attributed to the micro-cracking of the frustules that might be resulted from higher density of the cristobalite than that of the opal and accompanying reduction of the surface area and the surface pore sizes that might impair the resin-frustule interlocking and intrusion.