Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
10 results
Search Results
Article Citation - WoS: 5Citation - Scopus: 6Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel(Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.Article Citation - WoS: 3Citation - Scopus: 4Microfluidic-Assisted Preparation of Nano and Microscale Chitosan Based 3d Composite Materials: Comparison With Conventional Methods(Wiley, 2022) Kimna, Ceren; Değer, Sibel; Tamburacı, Sedef; Tıhmınlıoğlu, FundaAlthough nanofillers contribute to improved physical characteristics and biological functionalities of polymer-based biomaterials, their dispersion in polymer matrices is still a challenging issue in terms of obtaining consistency for the inherent properties. To tackle this problem, homogenization techniques are applied to disperse the nanofillers in such polymers, however, these methods can cause undesired changes especially in the rheological properties and the physical structure of the biopolymer matrices. Recently, as a novel homogenization technique, microfluidization has been used to homogenize polymer nanocomposites to minimize these limitations. In this study, two different nanocomposite structures as chitosan/montmorillonite (CS/MMT) and chitosan/polyhedral oligomeric silsesquioxane nanocages (CS/POSS) were homogenized with microfluidization and investigated in terms of physical alterations. Furthermore, the effect of microfluidizer technique on material characteristics was compared with conventional homogenization techniques, i.e., ultrasonic bath and sonication in terms of solution, nano – (e.g., hydrodynamic size, drug encapsulation) and macroscopic material characteristics (e.g., porosity, mechanical properties, swelling and thermal degradation). It was found that the microfluidizer homogenization improves the physical characteristics in both nano and macroscale materials: Nanospheres obtained from CS/MMT composites showed enhanced stability, uniform size distribution (<100 nm, PDI: [removed]50%) whereas 3D porous CS/POSS scaffolds showed improved structural uniformity (i.e., homogeneous and interconnected microstructure) and enhanced thermal and mechanical properties. The obtained results indicate that the microfluidizer homogenization ensures a successful nanofiller dispersion in polymer matrices, thereby improving the biomaterial characteristics impressively compared to the sonication methods.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.Article Citation - WoS: 9Citation - Scopus: 9Synthesis and Characterization of Novel High Temperature Structural Adhesives Based on Nadic End Capped Mda-Btda Copolyimide(IOP Publishing Ltd., 2018) Acar, Oktay; Varış, Serhat; Işık, Tuğba; Tirkeş, Seha; Demir, Mustafa MuammerA series of novel copolyimide structural adhesives were synthesized using 4,4′-diaminodiphenylmethane (MDA), 3,4′-oxydianiline (ODA) and 3,3′,4,4′-benzophenonetetracarboxylic acid dianhydride (BTDA) as co-monomers, and nadic anhydride as an end cap reagent. The adhesives with different MDA and ODA contents were examined in terms of their structure, thermal stability, mechanical properties, and adhesive performance. They have glass transition temperatures (T g) about 400 °C, with thermal stability up to 500 °C. The effect of diamine monomer compositions on adhesion performance and processability of the copolyimides were studied. The copolyimides exhibited adhesion strength up to 16.3 MPa at room temperature. Nadic end capped MDA-BTDA-ODA copolyimide resins gained adjustable and controllable processability with the addition of ether bridged aromatic segments. The copolyimide adhesive with equimolar composition of MDA:ODA is distinguished form the both commercial PMR-15 and LARC RP-46 polyimides in terms of its better processability and mechanical performance.Article Citation - WoS: 14Citation - Scopus: 16Microstructure and Mechanical Properties of A357/Sic Nanocomposites Fabricated by Ultrasonic Cavitation-Based Dispersion of Ball-Milled Nanoparticles(SAGE Publications Inc., 2017) Kandemir, SinanIn this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.Article Citation - WoS: 19Citation - Scopus: 20Isothermal Crystallization Kinetics and Mechanical Properties of Polycaprolactone Composites With Zinc Oxide, Oleic Acid, and Glycerol Monooleate(John Wiley and Sons Inc., 2013) Alp, Burcu; Cesur, SerapThe isothermal crystallization and mechanical behavior of polycaprolactone (PCL) with zinc oxide (ZnO) with oleic acid and glycerol monooleate (GMO) were studied. Theoretical melting points calculated by the Flory-Huggins and Thompson-Gibbs models were thoroughly compared with differential scanning calorimetry experimental observations. The isothermal crystallization kinetic parameters by Avrami analysis showed that crystallization was controlled by nucleation, crystal growth was spherical, and the nucleation type changed between thermal and athermal nucleation. X-ray diffraction showed that when the additives were used together both the crystal thickness and the degree of crystallinity increased. A multiple-response regression analysis was made with the ZnO, oleic acid, and GMO concentrations as variables and the crystallinity as output. Interaction parameters by the Pukanzky model were calculated from the tensile strength at the yield point and indicated that the addition of oleic acid or GMO improved the interface between the ZnO particles and PCL.Article Citation - WoS: 17Citation - Scopus: 21Effects of Particle Size and Electrical Resistivity of Filler on Mechanical, Electrical, and Thermal Properties of Linear Low Density Polyethylene-Zinc Oxide Composites(John Wiley and Sons Inc., 2013) Özmıhçı Ömürlü, Filiz; Balköse, DevrimThe effects of particle size and electrical resistivity of zinc oxide (ZnO) on mechanical properties, electrical and thermal conductivities of composites made with linear low density polyethylene (LLDPE) were investigated. Micron sized (mZnO), submicron sized (sZnO), and nano sized (nZnO) powders having resistivities of 1.5 × 106, 1.5 × 109, and 1.7 × 108 were used to prepare composites with 5-20 vol % filler. The tensile strength was lowered and the modulus of elasticity of the composites was increased with ZnO addition. Rather than the particle size of the ZnO, its initial resistivity and aspect ratio affected the resistivity of composites. The resistivity of the LLDPE was lowered from 2.3 × 1016 Ω cm down to 1.4 × 1010 Ω cm with mZnO addition. Thermal conductivity of the composites was increased with ZnO addition 2.5-3 times of the polymer matrix. The composites can be used for electrostatically dissipating and heat sink applications due to their decreased electrical resistivity and increased thermal conductivity.Article Citation - WoS: 13Citation - Scopus: 18Effect of Corn-Zein Coating on the Mechanical Properties of Polypropylene Packaging Films(John Wiley and Sons Inc., 2011) Tıhmınlıoğlu, Funda; Atik, İsa Doğan; Özen, BanuIn this study, a novel film structure of corn zein coated on polypropylene (PP) synthetic films for food packaging applications was developed, and the mechanical properties of the resulting coated film, as affected by the coating formulation, were investigated. Composite structures of PP films coated with corn zein were obtained through a simple solvent casting method. Different amounts of corn zein (5 and 15%) were dissolved in 70 and 95% aqueous ethanol solution at 50 C. Solutions of corn zein plasticized with poly(ethylene glycol) and glycerol (GLY) at various levels (20 and 50%) were applied on corona-discharge-treated PP. A statistical analysis based on full factorial design was performed to examine the influence of the coating formulation on the final properties of the corn-zein-coated PP films. A significant (p < 0.05) improvement in the coated film’s mechanical properties was observed compared to those of the uncoated PP. The effect of the plasticization of the coating solutions was also quite significant. In general, GLY provided better improvements in the mechanical properties of the corn-zein-coated PP films. The statistical analysis of the results showed that the corn-zein and plasticizer concentrations and plasticizer type used in the coating formulations were more effective parameters and had significant effects on the mechanical behavior of the coated PP films. In conclusion, corn-zein coatings could have potential as alternatives to conventional synthetic polymers used in composite multilayer structures for food packaging applications.Article Citation - WoS: 64Citation - Scopus: 70Mechanical and Morphological Properties of Recycled High-Density Polyethylene, Filled With Calcium Carbonate and Fly Ash(John Wiley and Sons Inc., 2006) Atikler, Ulaş; Başalp, Dildare; Tıhmınlıoğlu, FundaIn this study, mechanical and morphological properties of composites made up of recycled high-density polyethylene (HDPE) filled with calcium carbonate and fly ash (FA) were studied. Interfacial interactions were modified to improve the filler compatibility and mechanical properties of the composites by surface treatment of the FA filler with 3-amino propyl triethoxy silane. The composites were prepared by using a Thermo Haake Rheomixer. Effect of filler loading and treatment of FA with silane coupling agent on mechanical and morphological properties were investigated and it was found that silane treatment indicated significant improvements on the mechanical properties of the HDPE-FA composites. The improvement with silane treatment of FA was also confirmed by applying the Pukanszky model. Scanning electron microscopy on the fracture surface of composites had given direct evidence of better interfacial adhesion via silane treatment.Article Citation - WoS: 24Citation - Scopus: 28Stress Wave Propagation Effects in Two- and Three-Layered Composite Materials(SAGE Publications Inc., 2004) Taşdemirci, Alper; Hall, Ian W.; Gama, Bazle A.; Güden, MustafaMultilayer materials consisting of ceramic and glass/epoxy composites have been subjected to high strain rate compression testing using the Split Hopkinson Pressure Bar. The samples were extensively strain gaged so that dynamic data were generated directly from the samples during testing. Output data from the experiments were compared with numerical simulations of the same experiments and good agreement was noted. It was found that the stress distribution within samples was quite inhomogeneous and that stresses were highest in the region of the bar–sample interface. The presence of a rubber interlayer between the ceramic and glass/epoxy decreased the stress in both components but dramatically increased the degree of stress inhomogeneity.