Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
Search Results
Article Citation - WoS: 35Citation - Scopus: 35Cvd Graphene/Sic Uv Photodetector With Enhanced Spectral Responsivity and Response Speed(Elsevier, 2023) Jehad, Ala K.; Fidan, Mehmet; Ünverdi, Özhan; Çelebi, CemA self-powered, high-performance graphene/Silicon Carbide (G/4H-SiC) ultraviolet Schottky junction photodetector has been fabricated, and the effect of using monolayer and bilayer graphene on the device performance parameters was investigated. P-type graphene sheets were grown by the chemical vapor deposition (CVD) method, while 4H-SiC material consists of an epilayer structure of n-/n+ on bulk n-SiC. Two photodetector devices have been studied, one with monolayer graphene (MLG) and the other with bilayer graphene (BLG). The proposed photodetector structure reveals the highest spectral responsivity known of a G/4H-SiC UV photodetector so far. Electronic and optoelectronic characterizations were done under an ultraviolet wavelength range from 240 to 350 nm. The results show two spectral responsivity maxima (Rmax) at 285 nm and 300 nm wavelengths. Exhibiting two maxima in spectral responsivity and detectivity is caused by the constructive and destructive interference effects of multiple reflections at the SiC epilayer's interfaces. The photodetector devices exhibit high spectral responsivity (R ? 0.09 AW?1), maximum detectivity (D* ? 2.9 × 1012 Jones), and minimum noise equivalent power (NEP ? 0.17 pWHz-1/2) in both devices. Using bilayer graphene instead of monolayer showed no significant change in both the photogenerated current and the spectral responsivity due to the higher absorption coefficient of bilayer graphene, however, it exhibited a significant improvement in the response speed. The response speed was found to increase by 50 % when bilayer graphene was used as a hole collecting electrode in the G/4H-SiC junction. This is because bilayer graphene creates a narrower depletion layer and higher electric field, which promotes efficient charge separation and recombination. © 2023 Elsevier B.V.Article Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.