Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Article Citation - WoS: 24Citation - Scopus: 23Photovoltaic Performance of Magnetron Sputtered Antimony Selenide Thin Film Solar Cells Buffered by Cadmium Sulfide and Cadmium Sulfide /Zinc Sulfide(Elsevier B.V., 2023) Cantas, A.; Aygün, Gülnur; Gundogan, S.H.; Özyüzer, Lütfi; Turkoglu, F.; Koseoglu, H.; Aygun, G.; Ozyuzer, L.; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyAntimony selenide (Sb2Se3)-based thin-film solar cells have recently attracted worldwide attention as an abundant, low-cost, and efficient photovoltaic technology. The highest efficiencies recorded for Sb2Se3 solar cells have been obtained using cadmium sulfide (CdS) as a buffer layer. The Cd-included hybrid buffer layers could be one option to increase device efficiency through more effective usage of light. Therefore, in this work, the effect of single CdS and hybrid CdS/zinc sulfide (ZnS) buffer layers on the photovoltaic performance of Sb2Se3 thin-film solar cells has been investigated in detail. Sb2Se3 thin films have been deposited on molybdenum (Mo)-coated soda-lime glass (SLG) substrates by radio frequency magnetron sputtering technique followed by a post-heat treatment process. The morphological, and structural properties of Sb2Se3 thin films have been investigated by X-Ray Diffraction and Scanning Electron Microscopy. To compare the device performances of single CdS and hybrid CdS/ZnS buffered Sb2Se3 thin-film solar cells, SLG/Mo/Sb2Se3/CdS/ZnS/indium tin oxide (ITO) and SLG/Mo/Sb2Se3/CdS/ITO structures have been fabricated. The findings of this study have revealed a reduction in solar cells’ performance from η=3.93% for CdS buffer to η=0.13% for CdS/ZnS hybrid buffer. The change in the solar cell performance using the CdS/ZnS hybrid buffer has been discussed in detail. © 2023 Elsevier B.V.Conference Object Citation - Scopus: 1Daylight Performance and Lighting Energy Savings of Amorphous and Crystalline Silicon Solar Cells in an Architecture Studio(IEEE, 2023) Taşer, Aybüke; Kazanasmaz, Zehra Tuğçe; 02.02. Department of Architecture; 02. Faculty of Architecture; 01. Izmir Institute of TechnologySemi-transparent photovoltaic (PV) glass increased its popularity due to its energy and environmental advantages, which can generate electricity on-site and utilize natural daylight. They use thin-film solar cells to allow daylight to enter space and generate electrical energy. Crystalline and amorphous silicon (a-Si) solar cells are the most prominent in literature and industry due to their high efficiency and sufficient transparency. This study aims to assess the daylight and lighting energy-saving potential of thin-film crystalline and a-Si photovoltaic glass in an architecture studio in Izmir, Turkey. The simulation engine applied two types of solar cells on existing windows to evaluate the advantage of such glass for daylight performance and lighting energy consumption. Spatial Daylight Autonomy (sDA), a climate-based annual daylight performance metric, evaluates the daylight performance of the studio. Research findings note that such solar cells enhance the visual comfort of occupants and the daylight performance of the studio. In addition, crystalline silicon solar cells can cover the studio's whole lighting loads in the summer and fall seasons and balance them up to 66% and 23% in the spring and winter seasons, respectively. These have higher transmittance and peak power, thus; resulting in higher energy and daylight performance. © 2023 IEEE.Article Citation - WoS: 6Citation - Scopus: 5Structural and Optical Characteristics of Antimony Selenosulfide Thin Films Prepared by Two-Step Method(Springer, 2022) Türkoğlu, Fulya; Ekren, Memduh Emirhan; Özyüzer, Lütfi; Yakıncı, Kübra; Aygün, Gülnur; Aygün, Gülnur; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyAntimony triselenide (Sb2Se3) is one of the most promising absorber material choices among the inorganic semiconductors that has attracted much attention today. However, highest recorded efficiencies for Sb2Se3 solar cells are still lower than ideal. Exploring antimony selenosulfide (Sb-2(SxSe1-x)(3)) to increase device performance is one option because some features of alloyed Sb-2(SxSe1-x)(3) depend on composition such as bandgap and band position. In this study, two-step process was used to grow Sb-2(SxSe1-x)(3) thin films. In the first stage, Sb2Se3 thin films were deposited on soda lime glass substrates using direct current magnetron sputtering technique. In the second stage, Sb2Se3 thin films were exposed to sulfurization process in a quartz ampoule to obtain Sb-2(SxSe1-x)(3) thin films. Characterization results showed that morphological, optical, and structural properties of Sb-2(SxSe1-x)(3) thin films grown by presented method were highly dependent on amount of sulfur in the films. By the adjustment of the S/S + Se atomic ratio, Sb-2(SxSe1-x)(3) absorber materials with suitable bandgap, favorable orientation and compact morphology can be obtained for photovoltaic applications.Article Citation - WoS: 51Citation - Scopus: 48Cu2znsns4-Based Thin Films and Solar Cells by Rapid Thermal Annealing Processing(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Özyüzer, Lütfi; Mainz, R.; Özyüzer, Lütfi; Unold, T.; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study, kesterite Cu2ZnSnS4 (CZTS) absorber layers were fabricated by DC magnetron sputtering deposition of metallic Cu-Zn-Sn precursors, followed by an annealing treatment in sulfur vapor atmosphere at 600 °C for 3 min using rapid thermal processing (RTP). Three types of stacked metallic films were prepared and included pre-annealing of Cu-Sn stacks in order to induce preferential Cu-Sn alloying. The chemical composition of the sulfurized films was obtained by X-ray fluorescence (XRF) before and after etching the samples in KCN solution. All CZTS thin films are found to be Cu-poor and Zn-rich. Structural characterizations were performed by X-ray diffraction (XRD) and Raman spectroscopy to investigate the impact of pre-annealing on the structural properties of the precursors and final CZTS films. Glow discharge optical emission spectroscopy (GDOES) shows that pre-annealing of the precursors can improve depth homogeneity of the CZTS films. Photoluminescence spectra and the optical band gap energy values are compatible with literature. Selected samples were processed to solar cells and characterized.Article Citation - WoS: 22Citation - Scopus: 23Effect of Heat Treating Metallic Constituents on the Properties of Cu2znsnse4 Thin Films Formed by a Two-Stage Process(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Başol, B. M.; Aygün, Gülnur; Özyüzer, Lütfi; Aygün, Gülnur; Özyüzer, Lütfi; Bacaksız, Emin; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study Cu2ZnSnSe4 (CZTSe) thin films were grown by a two-stage process that involved sputter deposition of a Cu/Sn/Zn/Cu metallic stack, annealing the stack at various temperatures for 30 min, evaporation of a Se cap over the metallic stack thus forming a precursor layer, and subjecting the precursor layer to a final high temperature reaction step at 550 °C. Different samples were prepared with annealing temperatures of the metallic stacks ranging from 200 °C to 350 °C. The results showed that heat treatment of the metallic stacks did not cause much change in their morphology and elemental composition, however their phase content changed noticeably when the anneal temperature was raised to 250 °C. Specifically, while the metallic films were dominated by CuSn and Cu5Zn8 phases at low temperatures, the dominant phase shifted to Cu6Sn5 at the annealing temperature of 250 °C and higher. Also formation of a distinct Cu3Zn2 phase was observed upon annealing at temperatures at or above 250 °C. After reaction with Se, the CZTSe layer obtained from the metallic film, which was annealed at 250 °C was found to be the best n terms of its composition, crystalline quality and purity, although it contained a small amount of CuSe. The other layers were found to contain small amounts of other secondary phases such as SnSe, CuSe2, ZnSe and Cu2SnSe3. SEM micrographs showed denser structure for CZTSe layers grown from metallic films annealed at or above 250 °C. Optical band gap, resistivity and carrier concentration of the best quality CZTSe film were found to be about 0.87 eV, 2 Ω-cm and 4 × 1017 cm− 3, respectively.Article Citation - WoS: 36Citation - Scopus: 37Influence of Copper Composition and Reaction Temperature on the Properties of Cztse Thin Films(Elsevier Ltd., 2016) Olgar, Mehmet Ali; Atasoy, Y.; Özyüzer, Lütfi; Aygün, Gülnur; Özyüzer, Lütfi; Bacaksız, Emin; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study Cu2ZnSnSe4 (CZTSe) compound layers were grown using a two-stage technique that involved deposition of metallic precursors (Cu, Zn, and Sn) and Se in the first stage, followed by reaction of all the species at temperatures between 525 °C and 600 °C, during the second stage of the process. Two sets of samples, one with Cu-poor, Zn-rich and the other with Cu-rich, Zn-rich compositions, were prepared and their structural, optical and electrical properties were measured. XRD analyses showed the characteristic peaks of CZTSe regardless of the Cu content and the processing temperature. However, for samples reacted at temperatures of 575 °C and 600 °C a Cu2-xSe secondary phase separation was detected for all films suggesting that the reaction temperatures should be limited to values below 575 °C in a two-stage process such as ours. Excessive Sn loss was also present in samples processed at the highest temperatures. Raman scattering measurements confirmed formation of the CZTSe kesterite structure, and also indicated a small ZnSe phase, which could not be detected by XRD. Scanning electron micrographs demonstrated dense film structure with the Cu-rich films having smoother morphology. Optical characterization showed that increasing the Cu content in the compound layers caused a reduction in the optical band gap values due to increased interaction between the Cu-3d orbital electrons and the Se-4p orbital electrons. Electrical measurements showed that the carrier concentration increased with Cu content.