Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
12 results
Search Results
Now showing 1 - 10 of 12
Article Citation - WoS: 11Citation - Scopus: 13Magnesium-Ion Battery Anode From Polymer-Derived Sioc Nanobeads(Wiley, 2023) Guo, Wuqi; Kober, Delf; Gurlo, Aleksander; Bekheet, Maged F.; İçin, Öykü; Ahmetoğlu, Çekdar VakıfTin-containing silicon oxycarbide (SiOC/Sn) nanobeads are synthesized with different carbon/tin content and tested as electrodes for magnesium-ion batteries. The synthesized ceramics are characterized by thermogravimetric-mass spectroscopy, Fourier-transform infrared spectroscopy, X-ray diffraction (XRD), Raman spectroscopy, N2 sorption analysis, scanning electron microscope, energy-dispersive X-ray, and elemental analysis. Galvanostatic cycling tests, rate performance tests, electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) tests, and ex situ XRD measurements are conducted. Results of battery performance tests present a high capacity of 198.2 mAh g-1 after the first discharging and a reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1. Excellent rate performance efficiency of 85.2% is achieved. Battery performances in this research are influenced by surface area, and tin contentof the SiOC/Sn nanobeads. EIS, CV tests, and ex situ XRD measurements reveal that higher surface area contributes to higher capacity by providing more accessible Mg2+ ion storage sites and higher rate capability by improving the diffusion process. Higher Sn content increases battery capacity through reversible Mg-Mg2Sn-Mg alloying/dealloying process and improves the rate performances by increasing electrical conductivity. Besides, SiOC advances cycling stability by preventing electrode collapse and enhances the capacity due to higher surface capacitive effects. SiOC nanobeads containing Sn nanoparticles are synthesized and tested as anode for magnesium-ion batteries. The anodes show high performance with reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1 and excellent rate performance efficiency of 85.2% from 50 to 500 mA g-1.imageArticle Citation - WoS: 8Citation - Scopus: 8Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels(American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar VakıfThis work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.Article Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.Article Citation - WoS: 18Citation - Scopus: 22Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes(American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, AleksanderLab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.Article Citation - WoS: 8Citation - Scopus: 11Spreadability of Metal Powders for Laser-Powder Bed Fusion Via Simple Image Processing Steps(MDPI, 2022) Ahmetoğlu, Çekdar Vakıf; Hasdemir, Beyza; Biasetto, LisaThis paper investigates the spreadability of the spherical CoCrWMo powder for laser- powder bed fusion (PBF-LB) by using image processing algorithms coded in MATLAB. Besides, it also aims to examine the spreadability dependence with the other characteristics such as powder size distribution, apparent density, angle of repose. Powder blends in four different particle size distributions are prepared, characterized, and spreadability tests are performed with the PBF-LB. The results demonstrate that an increase in fine particle ratio by volume (below 10 µm) enhances the agglomeration and decreases the flowability, causing poor spreadability. These irregularities on the spread layers are quantified with simple illumination invariant analysis. A clear relation between powder spreadability and 3D printed structures properties in terms of residual porosity could not be defined since structural defects in 3D printed parts also depends on other processing parameters such as spatter formation or powder size over layer height ratio.Article Citation - WoS: 19Citation - Scopus: 21Synthesis and Additive Manufacturing of Calcium Silicate Hydrate Scaffolds(Elsevier, 2021) Oğur, Ezgi; Botti, Renata; Bortolotti, Mauro; Colombo, Paolo; Ahmetoğlu, Çekdar VakıfA Calcium silicate hydrate (CSH) powder containing above 60 wt% xonotlite (remaining being tobermorite, scawtite and calcite) were produced from lime and ordinary recycled soda-lime glass via simple hydrothermal synthesis route. The thermogravimetric analysis demonstrated only similar to 20%weight loss up to 800 degrees C (at about the transformation temperature of CSHs to wollastonite), reaching a plateau in the 800-1200 degrees C temperature range. The synthesized CSH powder was employed for the fabrication of both green and heat-treated scaffolds by additive manufacturing (AM), possessing a high porosity (>80 vol%) and limited strength (similar to 0.9 MPa). (c) 2021 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).Article Citation - WoS: 103Citation - Scopus: 110Cold Sintering of Ceramics and Glasses: a Review(Elsevier Ltd., 2020) Ahmetoğlu, Çekdar Vakıf; Karacasulu, LeventTraditionally ceramic artifacts are processed at high temperatures (> 1000 degrees C) by classical sintering techniques such as solid state, liquid phase and pressure-assisted sintering. Recently, inspired from the geology, novel sintering approaches that allow the densification of ceramic components at relatively low temperatures <= 400 degrees C have been proposed. While initial efforts for such low temperature densification concept were developed in the mid-70s, the topic has become increasingly prominent in the last decade. Currently, these low temperature methods can be classified into four main groups: (i) hydrothermal reaction sintering (HRS), (ii) hydrothermal hot pressing (HHP), (iii) pressure-assisted densification techniques: room-temperature densification (RTD), cold sintering (CS), warm press (WP), and finally no-pressure assisted method called (iv) reactive hydrothermal liquid phase densification (rHLPD). Above named techniques are commonly assisted by an aqueous solution used as either reactant or transient liquid phase to assist densification. Starting from the background in traditional sintering processes, this review aims to explore in depth the existing literature about low temperature densification approaches along with their advantages & disadvantages, and probable application areas.Correction Citation - Scopus: 1Corrigendum To “hierarchically Porous Polymer Derived Ceramics: a Promising Platform for Multidrug Delivery Systems”[mater. Des. 140(supplement C) (2018) 37–44](Elsevier Ltd., 2018) Ahmetoğlu, Çekdar Vakıf; Zeydanlı, Damla; Özalp, Veli Cengiz; Borsa, Barı Ata; Soraru, Gian DomenicoThe authors regret to inform that The TMTVS ratios for samples were written incorrectly. The true weight ratios for PHMS/LDH/PDMS/TMTVS blends should be as follows: Bio1 = 1/0.055/0.25/0.055, and Bio2 = 1/0.055/1/0.055. The discussion in the study is not affected by this mistype and actually the previous paper [1] cited also in the paper as ref.#44 gives right values for the sample preparation. The authors would like to apologize for the inconvenience caused.Article Citation - WoS: 11Citation - Scopus: 13Production and Properties of Phase Separated Porous Glass(Elsevier, 2020) Ertuş, E. Burak; Ahmetoğlu, Çekdar Vakıf; Öztürk, AbdullahA sodium borosilicate glass (SBG) was produced by conventional melt-quenching. As cast glass was heat treated to induce phase separation (SBG-HT), followed by acid leaching with HCl to dissolve one of the separated phases; i.e. alkali rich borate phase, so that a porous glass (PG) was obtained. In order to alter the pore structure, produced PG was subsequently alkali (NaOH) leached or alternatively heat treated. The samples were characterized by techniques including XRD, SEM, N-2 adsorption/desorption. The total pore volume for PG was found to be 0.314 cm(3)/g, reached to 0.370 cm(3)/g by alkali leaching, instead decreased to 0.227 cm(3)/g by heat treatment. The microhardness and tribological properties of SBG-HT and all PGs were evaluated by Vickers hardness and by pin on disk tribometer. For all PGs the microhardness values were lower, instead the wear rates were higher than that of the parent SBG-HT.Article Citation - WoS: 14Citation - Scopus: 17Electrical Characteristics of Low Temperature Densified Barium Titanate(Elsevier, 2020) Karacasulu, Levent; Tokkan, Melike; Bortolotti, Mauro; Ischia, Gloria; Adem, Umut; Ahmetoğlu, Çekdar VakıfA low temperature densification technique, i.e. reactive hydrothermal liquid-phase densification (rHLPD) was followed to obtain highly dense BaTiO3 components at temperatures <= 240 degrees C. The formed ceramics were characterized concerning not only the structural features but also the electrical properties. The increase of both reaction time and temperature resulted in enhanced densification of BaTiO3 components reaching about 90% of theoretical density. The presence of the tetragonal BaTiO3 was demonstrated by both XRD and TEM analysis. Despite the low reaction temperatures, the samples showed promising dielectric, ferroelectric and piezoelectric functionality without additional annealing. A broad dielectric peak was observed around 135 degrees C at the Curie temperature; saturated hysteresis loops and corresponding butterfly-shaped strain-electric field loops were obtained. BaTiO3 sample subjected to hydrothermal reaction at 240 degrees C for 72 h yielded a piezoelectric coefficient of 84 pC/N.