Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
29 results
Search Results
Now showing 1 - 10 of 29
Article Citation - WoS: 7Citation - Scopus: 6Thickness Gradient in Polymer Coating by Reactive Layer-By Assembly on Solid Substrate(Amer Chemical Soc, 2023) Özenler, Sezer; Alkan, Ali Ata; Gunay, Ufuk Saim; Dağlar, Özgün; Durmaz, Hakan; Yıldız, Ümit HakanThe study describes a simple yet robust methodology for forming gradients in polymer coatings with nanometer-thickness precision. The thickness gradients of 0-20 nm in the coating are obtained by a reactive layer-by-layer assembly of polyester and polyethylenimine on gold substrates. Three parameters are important in forming thickness gradients: (i) the incubation time, (ii) the incubation concentration of the polymer solutions, and (iii) the tilt angle of the gold substrate during the dipping process. After examining these parameters, the characterization of the anisotropic surface obtained under the best conditions is presented in the manuscript. The thickness profile and nanomechanical characterization of the polymer gradients are characterized by atomic force microscopy. The roughness analysis has demonstrated that the coating exhibited decreasing roughness with increasing thickness. On the other hand, Young's moduli of the thin and thick coatings are 0.50 and 1.4 MPa, respectively, which assured an increase in mechanical stability with increasing coating thickness. Angle-dependent infrared spectroscopy reveals that the C-O-C ester groups of the polyesters exhibit a perpendicular orientation to the surface, while the C=C groups are parallel to the surface. The surface properties of the polymer gradients are explored by fluorescence microscopy, proving that the dye's fluorescence intensity increases as the coating thickness increases. The significant benefit of the suggested methodology is that it promises thickness control of gradients in the coating as a consequence of the fast reaction kinetics between layers and the reaction time.Conference Object Citation - WoS: 3Citation - Scopus: 3Halloysite Nanotube Loaded Polyamide Nanocomposites: Structural, Morphological, Mechanical, Thermal and Processing Behaviors(American Institute of Physics, 2023) Akar, Alinda Öykü; Yıldız, Ümit Hakan; Tayfun, ÜmitIn this study, the polyamide 6 (PA) matrix was reinforced with the purified, fine ground and amino-silane treated halloysite nanotubes (HNT) at different concentrations. The preparation of composites was carried out using a lab-scale twin-screw micro-compounder with loading ratios at 0.5, 1, 3, and 20% by weight, and the test samples were prepared by the injection-molding process. According to mechanical test results, additions of HNT to the PA matrix caused slight improvements in tensile strength and Youngs' modulus parameters. The optimum concentrations for all of the additives used were estimated by comparison of mechanical test data. The addition of aminosilane-modified HNT resulted in a higher impact performance at high loading levels up to 3% concentrations. Further addition of HNT caused a reduction in the mechanical parameters of composites. Thermal studies revealed that the glass transition temperature of PA shifted to higher values after HNT mineral inclusions. Thermo-mechanical results showed that storage moduli of PA exhibited improvement with an increase in HNT content. The distributions of HNT clay into the PA phase were visualized with SEM images. Based on these observations, a high level of dispersion homogeneity was achieved for lower filling ratios. According to melt-flow and force measurements, composites filled with 20% of HNT displayed a remarkable increase in exerted force during melt-blending. © 2023 Author(s).Article Citation - WoS: 4Citation - Scopus: 4Colorimetric Assaying of Exosomal Metabolic Biomarkers(MDPI, 2023) Yan, Evelias; Goyal, Garima; Yıldız, Ümit Hakan; Boehm, Bernhard O.; Palaniappan, AlagappanExosomes released into the extracellular matrix have been reported to contain metabolic biomarkers of various diseases. These intraluminal vesicles are typically found in blood, urine, saliva, breast milk, cerebrospinal fluid, semen, amniotic fluid, and ascites. Analysis of exosomal content with specific profiles of DNA, microRNA, proteins, and lipids can mirror their cellular origin and physiological state. Therefore, exosomal cargos may reflect the physiological processes at cellular level and can potentially be used as biomarkers. Herein, we report an optical detection method for assaying exosomal biomarkers that supersedes the state-of-the-art time consuming and laborious assays such as ELISA and NTA. The proposed assay monitors the changes in optical properties of poly(3-(4-methyl-3'-thienyloxy) propyltriethylammonium bromide) upon interacting with aptamers/peptide nucleic acids in the presence or absence of target biomarkers. As a proof of concept, this study demonstrates facile assaying of microRNA, DNA, and advanced glycation end products in exosomes isolated from human plasma with detection levels of ~1.2, 0.04, and 0.35 fM/exosome, respectively. Thus, the obtained results illustrate that the proposed methodology is applicable for rapid and facile detection of generic exosomal biomarkers for facilitating diseases diagnosis.Conference Object Citation - WoS: 1Citation - Scopus: 1Biomimetic Peptide-Conjugated Membranes for Developing an Artificial Cornea(IEEE, 2022) Sunal, Gülşah; Pulat, Günnur; Akgün, İsmail Hakkı; Güven, Sinan; Yıldız, Ümit Hakan; Karaman, Ozan; Horzum, NesrinThe corneal endothelium is composed of a single layer of specialized endothelial cells, protecting, and nourishing the inner surface of the cornea. Corneal endothelial cells do not proliferate after birth and their number decrease with age. Trauma, inflammation, or surgical intervention can cause cell loss. When damage is extensive and the density of corneal endothelial cells decreases to a critical level, it results in corneal edema and vision loss. Besides them, when corneal endothelium has irreversible damage, the only treatment way is corneal transplantation. But there are some drawbacks such as finding donors, immune reactions, and the number of patients waiting on the transplantation lists for years. Tissue engineering approaches can provide promising alternatives for the regeneration of corneal endothelium tissue. Peptides can be used to modify and functionalize the scaffolds, allowing for the production of bioactive and biomimetic surfaces. Peptide-modified scaffold surfaces might direct and enhance the behaviors of cells. In this study, the aim was to functionalize the polycaprolactone (PCL) membranes with tissue-specific peptides and to characterize the peptide-conjugated membranes by Fourier-Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and X-ray Photoelectron Spectroscopy (XPS) analysis. The synthesized peptides were successfully conjugated on the PCL biomembranes.Article Citation - WoS: 14Citation - Scopus: 13Investigations of Polyamide Nano-Composites Containing Bentonite and Organo-Modified Clays: Mechanical, Thermal, Structural and Processing Performances(Walter de Gruyter GmbH, 2021) Akar, Alinda Öykü; Yıldız, Ümit Hakan; Tayfun, ÜmitPolyamide 6 (PA) matrix was reinforced with Na-activated bentonite, amino functional silane treated bentonite and organo-modified clays at different concentrations. The preparation of composites was carried out using melt-blending method and the test samples were prepared by injection-molding process. Mechanical, thermal, structural and processing investigations of PA based composites were reported performing via tensile, hardness, and impact tests, differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction analysis (XRD) and force measurements, respectively. According to mechanical test results, additions of fillers to PA matrix caused slight improvements for tensile strength and modulus parameters. Silane treated BNT exhibited improvement in mechanical results compared to Na-activated bentonite additions. Thermal studies revealed that decomposition and melting temperatures of PA shifted to higher values after inclusion of clay into polymer matrix. Results confirmed that organo-clay and bentonite additions with their lower filling ratios yielded enhancements for the mechanical and thermal performance of polyamide.Article Citation - WoS: 1Citation - Scopus: 1Gadolinium and Polythiophene Functionalized Polyurea Polymer Dots as Fluoro-Magnetic Nanoprobes(MDPI, 2022) Karabacak, Soner; Palaniappan, Alagappan; Tony, Tsang Siu Hon; Edwin, Teo Hang Tong; Gulyás, Balázs; Padmanabhan, Parasuraman; Yıldız, Ümit HakanA rapid and one-pot synthesis of poly 3-thiopheneacetic acid (PTAA) functionalized pol-yurea polymer dots (Pdots) using polyethyleneimine and isophorone diisocyanate is reported. The one-pot mini-emulsion polymerization technique yielded Pdots with an average diameter of ~20 nm. The size, shape, and concentration of the surface functional groups could be controlled by al-tering the synthesis parameters such as ultrasonication time, concentration of the surfactant, and crosslinking agent, and the types of isocyanates utilized for the synthesis. Colloidal properties of Pdots were characterized using dynamic light scattering and zeta potential measurements. The spherical geometry of Pdots was confirmed by scanning electron microscopy. The Pdots were post-functionalized by 1,4,7,10 tetraazacyclododecane-1,4,7,10-tetraacetic acid for chelating gadolinium nanoparticles (Gd3+) that provide magnetic properties to the Pdots. Thus, the synthesized Pdots possess fluorescent and magnetic properties, imparted by PTAA and Gd3+, respectively. Fluorescence spectroscopy and microscopy revealed that the synthesized dual-functional Gd3+-Pdots ex-hibited detectable fluorescent signals even at lower concentrations. Magnetic levitation experiments indicated that the Gd3+-Pdots could be easily manipulated via an external magnetic field. These findings illustrate that the dua-functional Gd3+-Pdots could be potentially utilized as fluorescent reporters that can be magnetically manipulated for bioimaging applications.Article Citation - WoS: 43Citation - Scopus: 46Glucuronoxylan-Based Quince Seed Hydrogel: a Promising Scaffold for Tissue Engineering Applications(Elsevier, 2021) Güzelgülgen, Meltem; Özkendir İnanç, Dilce; Yıldız, Ümit Hakan; Arslan Yıldız, AhuNatural gums and mucilages from plant-derived polysaccharides are potential candidates for a tissue-engineering scaffold by their ability of gelation and biocompatibility. Herein, we utilized Glucuron-oxylanbased quince seed hydrogel (QSH) as a scaffold for tissue engineering applications. Optimization of QSH gelation was conducted by varying QSH and crosslinker glutaraldehyde (GTA) concentrations. Structural characterization of QSH was done by Fourier Transform Infrared Spectroscopy (MR). Furthermore, morphological and mechanical investigation of QSH was performed by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The protein adsorption test revealed the suitability of QSH for cell attachment. Biocompatibility of QSH was confirmed by culturing NIH-3T3 mouse fibroblast cells on it. Cell viability and proliferation results revealed that optimum parameters for cell viability were 2 mg mi(-1)of QSH and 0.03 M GTA. SEM and DAPI staining results indicated the formation of spheroids with a diameter of approximately 300 pm. Furthermore, formation of extracellular matrix (ECM) microenvironment was confirmed with the Collagen Type-I staining. Here, it was demonstrated that the fabricated QSH is a promising scaffold for 3D cell culture and tissue engineering applications provided by its highly porous structure, remarkable swelling capacity and high biocompatibility. (C) 2021 Published by Elsevier B.V.Article Citation - WoS: 5Citation - Scopus: 6Toward Single-Layer Janus Crystals: Off-Balance Materials From Synthesis To Nanotechnology Applications(American Institute of Physics, 2021) Oğuztürk, H. Esra; Sözen, Yiğit; Akyol, Cansu; Özkendir İnanç, Dilce; Yıldız, Ümit Hakan; Şahin, HasanThe existence of things is directly related to their structural symmetry in a broad framework ranging from atoms to crystalline materials and from simple cells to complex organisms like humans. However, structural imbalance that occurs through natural or artificial means can provide completely different advantages. Molecules, crystals, and complex structures with structural imbalance constitute the family of Janus-type materials. This perspective provides a comprehensive discussion on the synthesis techniques of Janus-type materials, their use in fields from biology to materials science, and very recent studies on the family of 2D ultrathin graphene-like structures. We believe that, thanks to the advances in experimental techniques, the few-atom-sized off-balanced materials will be indispensable parts of the nanotechnology products that soon will be used in our daily lives.Article Citation - WoS: 2Citation - Scopus: 2Transition-Metal Direct C-H Arylation of Thiophene in Aqueous Media Via Potassium Peroxymonosulfate(John Wiley and Sons Inc., 2019) Özenler, Sezer; Kaya, Hakan; Elmacı, Nuran; Yıldız, Ümit HakanThis study covers the use of potassium peroxymonosulfate (PPS) which, is a mild and inexpensive catalyst, for direct coupling of C-H/C-H for water soluble thiophene. The 3-(4-methyl-3 '- thienyloxy)propyltriethylammonium bromide (M1) has been selected as model monomer that reacted PPS in 2.0, 0.20 and 0.020 monomer to PPS ratio. The reaction has been monitored via NMR spectroscopy revealing the monomer consumption and formation of dimers to tetramers as well as completion of reaction within 15 minutes. Resultant product is easily collected without tedious work up steps. The computational calculation has optimized the regularity of the coupling as head to tail, tail to tail, head to tail (HT-TT-HT) for tetramer. The regularity of tetramer which is further satisfied via NMR analysis showing emergence of new peaks at 3.56 and 4.48. The shifts in the UV maximum of reactive species have been monitored by absorbance spectroscopy showing time dependent red shift corresponds to growing from monomer to tetramers. The reaction has self-stopped due to low solubility of moderate condensates (higher than trimer), however further experiments have performed in water-organic mixtures showed great promises to obtain higher condensates.Article Citation - WoS: 39Citation - Scopus: 37Flow-Through Colorimetric Assay for Detection of Nucleic Acids in Plasma(Elsevier, 2019) Ammanath, Gopal; Yeasmi, Sanjida; Srinivasulu, Yuvasri; Vats, Mukti; Cheema, Jamal Ahmed; Nabilah, Fairuz; Liedberg, Bo; Yıldız, Ümit HakanA flow-through colorimetric assay for detection of nucleic acids in plasma is reported. The proposed assay features an array of four polyvinylidene fluoride (PVDF) membranes impregnated with cationic poly (3-alkoxy-4-methylthiophene) (PT) as an optical reporter. The sensing strategy is based on monitoring the changes in optical properties of PT, upon complexation with target nucleic acids in the presence and in the absence of their corresponding complementary peptide nucleic acids (PNAs). As a proof of concept, the proposed methodology is validated using two biomarkers; lung cancer associated microRNA (mir21) and hepatitis B virus DNA (HBV-DNA). The flow-through colorimetric assay enabled detection of mir21 and HBV-DNA in plasma without requiring tedious sample pre-treatment and clean up protocols. Colorimetric responses for mir21 and HBV-DNA were obtained at nanomolar concentrations over five orders of magnitudes (from 1 nM to 10 mu M), with a limit of detection of -0.6 nM and -2 nM in DI water and plasma, respectively. A logic gate system was developed to utilize the colorimetric assay responses as inputs for discrimination of mir21 and HBV-DNA and subsequently to obtain a profile of nucleic acids in samples that exceed respective clinical threshold limits, thereby enabling rapid and point of care (POC) disease diagnosis. Furthermore, the proposed methodology can be utilized for detection of a large number of nucleic acids in plasma by extending the array of PT impregnated membranes incorporated with their corresponding complementary PNAs. (C) 2019 Elsevier B.V. All rights reserved.
- «
- 1 (current)
- 2
- 3
- »