Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
12 results
Filters
Settings
Search Results
Now showing 1 - 10 of 12
Article Enhanced Oxidation and Thermal Shock Resistance of N-Type Mg2Si0.89(Sn0.1,Sb0.01) Thermoelectric Material Via Cr0.9Si0.1 Coating(Wiley-VCH Verlag GmbH, 2025) Gurtaran, Mikdat; Zhang, Zhenxue; Li, Xiaoying; Dong, HanshanIn this study, Cr0.9Si0.1 coatings are deposited onto Mg2Si0.89(Sn0.1Sb0.01) thermoelectric (TE) materials using a closed-field unbalanced magnetron sputtering system. The cyclic oxidation behavior of uncoated and Cr0.9Si0.1-coated TE materials is thoroughly investigated at 500 degrees C for 10 and 50 cycles, with each cycle lasting 1 h. Surface morphology, phase constitution, cross-sectional layer structure, and elemental distribution are analyzed using scanning electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. Oxidation kinetics are assessed by measuring the mass gain of samples after cyclic oxidation testing. The uncoated TE material exhibits significant surface degradation after cyclic oxidation, initially forming MgO particles, followed by the development of SiO2 and Mg2SiO4 phases in later stages. Encouragingly, the Cr0.9Si0.1 coating demonstrates excellent thermal stability on the n-type Mg2Si0.89(Sn0.1Sb0.01) substrate. Although some oxygen diffusion occurs along grain boundaries within the coating, it is effectively trapped, thereby preventing further penetration into the underlying substrate. The high oxygen affinity of Cr and/or Si atoms plays a critical role in blocking oxidation, offering robust protection. These findings strongly support the use of Cr0.9Si0.1 coatings as an effective antioxidant barrier for TE materials under harsh operational conditions, ensuring the long-term operation of TE modules at elevated temperatures.Article Citation - WoS: 37Citation - Scopus: 39Reaction of Methyl Radicals With Metal Powders Immersed in Aqueous Solutions(Wiley-VCH Verlag, 2003) Rusonik,I.; Polat,H.; Cohen,H.; Meyerstein,D.Methyl radicals radiolytically produced in aqueous solutions react efficiently with Cr0, Mn0, Fe0, Ni 0, Cu0 and Zn0 powders immersed in the solution. The Cr0, Mn0, Fe0, Ni0 and Zn0 powders reduce the radicals to form methane. On the other hand the Cu0 powder seems to oxidize the radicals. Surprisingly a part of the energy absorbed by the Cr0, Fe0, Ni 0 and Zn0 powders is transferred to the aqueous solution, thus increasing the radical yield. CH4, C2H4, C2H6, C3H6 and C3H 8 are formed when an aqueous deaerated buffer solution, pH 4-5, is added to powders of analytical iron, zinc, manganese and chromium. The source of these gases is carbon traces present, as atoms or atom clusters, in the "analytical" metal powders. These carbon atoms, when present on the surface of the metals, are reduced by the metal particles in aqueous solutions. This mechanism might be the source of light alkanes and alkenes in the prebiotic era. © Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2003.Article Citation - Scopus: 7Oxidation of Oregano Essential Oil Using Zeolite-Encapsulated Cr(salpn) Complex(SCIBULCOM, 2017) Bayraktar, Oğuz; Yerkesikli, Alev GüneşFlexible ligand (H2salpn, N,N´-bis(salicylidene)propane-1,3-diamine) was used to form complex with Cr(III) metal ion inside the cages of NaY-zeolite. The encapsulation of Cr(salpn) complex was confirmed with Fourier transform infrared (FT-IR). The encapsulated Cr(salpn) complex catalysed the liquid-phase oxidation of both carvacrol and thymol in the presence of hydrogen peroxide. The conversion range was found be between 35–39% for the oxidation of both carvacrol and thymol. A high yield of thymoquinone (TQ) was obtained along with other side-products such as, thymohydroquinone (THQ) and benzoquinones (BQ). Oxidation of carvacrol and thymol provided a TQ yield of 31.2 and 34.5%, respectively. Oxidation reaction did not occur in the absence of a catalyst. The Cr(salpn)-NaY catalyst was catalytically active with an acceptable leaching performance. Oxidation of oregano essential oil having carvacrol as major compound caused the formation of an essential oil rich in TQ. The carvacrol present in the oregano essential oil was converted into mainly TQ with 33.6% yield and 70% total conversion as a result of the side-products namely BQ, THQ, and several undefined products. © 2017 Scibulcom Ltd. All Rights Reserved.Article Citation - WoS: 24Citation - Scopus: 26Role of Surface Oxidation on the Size Dependent Mechanical Properties of Nickel Nanowires: a Reaxff Molecular Dynamics Study(Royal Society of Chemistry, 2017) Aral, Gürcan; Islam, Md Mahbubul; Van Duin, Adri C. T.Highly reactive metallic nickel (Ni) is readily oxidized by oxygen (O2) molecules even at low temperatures. The presence of the naturally resulting pre-oxide shell layer on metallic Ni nano materials such as Ni nanowires (NW) is responsible for degrading the deformation mechanisms and related mechanical properties. However, the role of the pre-oxide shell layer on the metallic Ni NW coupled with the complicated mechanical deformation mechanism and related properties have not yet been fully and independently understood. For this reason, the ReaxFF reactive force field for Ni/O interactions was used to investigate the effect of surface oxide layers and the size-dependent mechanical properties of Ni NWs under precisely controlled tensile loading conditions. To directly quantify the size dependent surface oxidation effect on the tensile mechanical deformation behaviour and related properties for Ni NWs, first, ReaxFF-molecular dynamics (MD) simulations were carried out to study the oxidation kinetics on the free surface of Ni NWs in a molecular O2 environment as a function of various diameters (D = 5.0, 6.5, and 8.0 nm) of the NWs, but at the same length. Single crystalline, pure metallic Ni NWs were also studied as a reference. The results of the oxidation simulations indicate that a surface oxide shell layer with limiting thickness of ∼1.0 nm was formed on the free surface of the bare Ni NW, typically via dissociation of the O-O bonds and the subsequent formation of Ni-O bonds. Furthermore, we investigated the evolution of the size-dependent intrinsic mechanical elastic properties of the core-oxide shell (Ni/NixOy) NWs by comparing them with their un-oxidized counterparts under constant uniaxial tensile loading. We found that the oxide shell layer significantly decreases the mechanical properties of metallic Ni NW as well as facilitates the initiation of plastic deformation as a function of decreasing diameter. The disordered oxide shell layer on the Ni NW's surface remarkably reduces the yield stress and Young's modulus, due to the increased softening effects with the decreasing NW diameter, compared to un-oxidized counterparts. Moreover, the onset of plastic deformation occurs at a relatively low yielding strain and stress level for the smaller diameter of oxide-coated Ni NWs in comparison to their pure counterparts. Furthermore, for pure Ni NWs, Young's modulus, the yielding stress and strain slightly decrease with the decrease in the diameter size of Ni NWs.Article Citation - WoS: 32Citation - Scopus: 34Effects of Oxidation on Tensile Deformation of Iron Nanowires: Insights From Reactive Molecular Dynamics Simulations(American Institute of Physics, 2016) Aral, Gürcan; Wang, Yun-Jiang; Ogata, Shigenobu; Van Duin, Adri C.T.The influence of oxidation on the mechanical properties of nanostructured metals is rarely explored and remains poorly understood. To address this knowledge gap, in this work, we systematically investigate the mechanical properties and changes in the metallic iron (Fe) nanowires (NWs) under various atmospheric conditions of ambient dry O2 and in a vacuum. More specifically, we focus on the effect of oxide shell layer thickness over Fe NW surfaces at room temperature. We use molecular dynamics (MD) simulations with the variable charge ReaxFF force field potential model that dynamically handles charge variation among atoms as well as breaking and forming of the chemical bonds associated with the oxidation reaction. The ReaxFF potential model allows us to study large length scale mechanical atomistic deformation processes under the tensile strain deformation process, coupled with quantum mechanically accurate descriptions of chemical reactions. To study the influence of an oxide layer, three oxide shell layer thicknesses of ∼4.81 Å, ∼5.33 Å, and ∼6.57 Å are formed on the pure Fe NW free surfaces. It is observed that the increase in the oxide layer thickness on the Fe NW surface reduces both the yield stress and the critical strain. We further note that the tensile mechanical deformation behaviors of Fe NWs are dependent on the presence of surface oxidation, which lowers the onset of plastic deformation. Our MD simulations show that twinning is of significant importance in the mechanical behavior of the pure and oxide-coated Fe NWs; however, twin nucleation occurs at a lower strain level when Fe NWs are coated with thicker oxide layers. The increase in the oxide shell layer thickness also reduces the external stress required to initiate plastic deformation.Article Citation - WoS: 48Citation - Scopus: 64Active Packaging of Ground Beef Patties by Edible Zein Films Incorporated With Partially Purified Lysozyme and Na 2edta(John Wiley and Sons Inc., 2011) Uysal Ünalan, İlke; Korel, Figen; Yemencioğlu, AhmetIn this study, antimicrobial activity of zein films incorporated with partially purified lysozyme and disodium ethylenediaminetetraacetic acid (Na 2EDTA) has been tested on selected pathogenic bacteria and refrigerated ground beef patties. The developed films containing 700μgcm -2 lysozyme and 300μgcm -2 Na 2EDTA showed antimicrobial activity on Listeria monocytogenes, Escherichia coli O157:H7, and Salmonella typhimurium. The application of lysozyme and Na 2EDTA incorporated zein films on beef patties significantly decreased total viable counts (TVC) and total coliform counts after 5days of storage compared to those of control patties (P<0.05). Zein films incorporated with lysozyme and Na 2EDTA or Na 2EDTA alone significantly slowed down the oxidative changes in patties during storage (P<0.05). Redness indices of patties coated with zein films were significantly lower than those of uncoated control patties during storage (P<0.05). This study demonstrated the potential usage of zein films containing lysozyme and Na 2EDTA for active packaging of refrigerated meat products. © 2011 The Authors. International Journal of Food Science and Technology.Article Citation - WoS: 7Citation - Scopus: 7The Roles of Thiol Oxidoreductases in Yeast Replicative Aging(Elsevier Ltd., 2010) Hacıoğlu, Elise; Esmer, Işıl; Fomenko, Dmitri E.; Gladyshev, Vadim N.; Koç, AhmetThiol-based redox reactions are involved in the regulation of a variety of biological functions, such as protection against oxidative stress, signal transduction and protein folding. Some proteins involved in redox regulation have been shown to modulate life span in organisms from yeast to mammals. To assess the role of thiol oxidoreductases in aging on a genome-wide scale, we analyzed the replicative life span of yeast cells lacking known and candidate thiol oxidoreductases. The data suggest the role of several pathways in controlling yeast replicative life span, including thioredoxin reduction, protein folding and degradation, peroxide reduction, PIP3 signaling, and ATP synthesis. © 2010 Elsevier Ireland Ltd.Article Citation - WoS: 11Citation - Scopus: 13Liquid-Phase Oxidation of Carvacrol Using Zeolite-Encapsulated Metal Complexes(American Chemical Society, 2006) Güneş, Alev; Bayraktar, Oğuz; Yılmaz, SelahattinWe report here the use of zeolite-encapsulated metal (salpn) complexes as catalysts in the oxidation reaction of the natural compound carvacrol in acetonitrile with hydrogen peroxide as the oxidant. No previous studies on the oxidation of carvacrol in the presence of metal salpn complexes have been reported. By using a general flexible ligand method, Cr(III), Fe(III), Bi(III), Ni(II), and Zn(II) complexes of N,N′-bis(salicylidene)propane1,3-diamine (H2salpn) encapsulated in NaY zeolite were prepared. All catalysts were characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses to confirm the complex encapsulation. The activities of all prepared catalysts for the oxidation of carvacrol and hydrogen peroxide were tested. The performances of all catalysts were compared on the basis of the leaching test results and carvacrol conversions. Thymohydroquinone and benzoquinones were observed as byproducts at high conversions of carvacrol. No product was formed in the absence of a catalyst. Fe(salpn)-NaY catalyst exhibited the highest carvacrol conversion of 27.6% with a yield of 22.0%, followed by Cr(salpn)-NaY catalyst with 23.5% carvacrol conversion and a yield of 17.6%. Other catalysts have shown relatively lower performances in terms of carvacrol conversion and leaching. The Cr(salpn)-NaY catalyst was found to be a more efficient catalyst than others on the basis of leaching and activity tests. With the selected catalyst Cr (salpn)-NaY, the effects of temperature and carvacrol/hydrogen peroxide molar ratio on carvacrol oxidation reactions were investigated. Increasing the temperature from 40 to 60 °C caused an increase in the thymoquinone yield from 6.2% to 16.0%. An increase in carvacrol/hydrogen peroxide molar ratio from 1 to 3 resulted in a decrease in the thymoquinone yield.Article Citation - WoS: 50Citation - Scopus: 53Nanoscale Oxide Growth on Al Single Crystals at Low Temperatures: Variable Charge Molecular Dynamics Simulations(American Physical Society, 2006) Hasnaoui, A.; Politano, O.; Salazar, J. M.; Aral, GürcanWe investigate the oxidation of aluminum low-index surfaces [(100), (110), and (111)] at low temperatures (300-600 K) and three different gas pressure values. We use molecular dynamics (MD) simulations with dynamic charge transfer between atoms where the interaction between atoms is described by the Es+ potential composed of the embedded atom method (EAM) potential and an electrostatic contribution. In the considered temperature range and under different gas pressure conditions, the growth kinetics follow a direct logarithmic law where the oxide thickness is limited to a value of ∼3 nm. The fitted curves allow us to determine the temperature and the pressure dependencies of the parameters involved in the growth law. During the adsorption stage, we observe a rotation of the oxygen pair as a precursor process to its dissociation. In most cases, the rotation aligns the molecule vertically to the Al surface. The separation distance after dissociation ranges from 3 to 9. Atomistic observations revealed that the oxide presents a dominant tetrahedral (Al O4) environment in the inner layer and mixed tetrahedral and octahedral (Al O6) environments in the outer oxide region when the oxide thickness reaches values beyond ∼2 nm.Article Citation - WoS: 98Citation - Scopus: 108Capacity and Mechanism of Phenol Adsorption on Lignite(Elsevier Ltd., 2006) Polat, Hürriyet; Molva, Murat; Polat, MehmetA raw lignitic coal from Soma, Turkey was investigated to determine its potential as an adsorbent for phenol removal from wastewaters. Kinetic batch tests demonstrated that phenol could be completely removed from solution given sufficient solids loading and reaction time. The adsorption capacity of 10 mg/g obtained with the lignite is low compared to those achievable with activated carbons (around 300 mg/g). However, when normalized for the surface area, the adsorption capacity was much larger for the lignite (1.3 mg/m2) than that generally observed with activated carbons (0.05-0.3 mg/m2). Hydrogen-bonding of the phenolic -OH with the oxygen sites on the lignite surface is the most likely mechanism for adsorption. Though water molecules also have affinity for the same oxygen sites, lateral benzene ring interactions make phenol adsorption energetically more favorable. Since phenol molecules adsorbed in this fashion would project their benzene rings into solution, formation of a second layer through the action of the dispersive π-π interactions between the benzene rings is very likely. Residual water quality with respect to major elements and heavy metals was within acceptable limits defined by the ASTM standards. Dissolution of organic matter from the lignite was also observed to be negligible.