Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
10 results
Search Results
Now showing 1 - 10 of 10
Article Citation - WoS: 1Citation - Scopus: 1Synthesis of Pristine Chitosan Foams with Enhanced Pore Structure, Surface Area, and Mechanical Strength for Tissue Engineering Applications(Iop Publishing Ltd, 2025) Polat, M.; Cropper, Chelsea; Ozdamar, A. B.; Polat, H.With its excellent biocompatibility, biodegradability, and antimicrobial activity, chitosan is a promising scaffold material for hard-tissue engineering. Yet, pristine chitosan foams typically lack the strength and porosity required for such use. Here we present a simple emulsion-templating approach to fabricate pristine chitosan foams with optimized strength and porosity. Sodium dodecyl sulfate (SDS), a widely used biocompatible anionic surfactant, was employed at trace levels to aid polymerization. The foams display a dual-scale pore morphology. Cavities of 150-300 mu m are separated by around 50 mu m thick chitosan walls containing large interconnecting openings. The walls are further populated with meso- and macropores of 50-500 nm. This architecture should support cell attachment and growth, facilitate proliferation, and enhance nutrient transport and metabolic exchange. The structure yields high surface area (up to 10 m2 g-1). Mechanically, the thick-walled cavities impart both elastic recovery and high compressive resistance (255 kPa at 40% strain from foams polymerized with 4% chitosan). A preliminary drug-release study using vancomycin confirmed excellent loading and sustained release.Article Citation - WoS: 20Citation - Scopus: 22Fabrication and Properties of Novel Porous Ceramic Membrane Supports From the (sig) Diatomite and Alumina Mixtures(Elsevier, 2022) Aouadja, Faycal; Bouzerara, Ferhat; Güvenç, Çetin Meriç; Demir, Mustafa M.In this paper, the manufacturing of macro-porous tubular ceramic supports for membranes is described. The novel supports are fabricated from natural diatomite and alumina raw materials using the extrusion method. The structure was analyzed by X-ray diffraction (XRD) and mercury porosimetry techniques; the presence of possible defects was investigated by scanning electron microscopy (SEM). The permeability has been measured from water flux in standard experiments. Experimental results show that the open porosity, the average pore size (APS), the pore size distribution, the strength, and the permeability of sintered supports, have been found to depend, mainly on the concentration of alumina (Al2O3) additive. Supports prepared with the addition of 10 wt.% of alumina and sintered at 1200 degrees C, can be considered as the most optimized; they have a porosity ratio of about 46%, an APS is around 7.7 mu m, a flexural strength value of about 28 MPa, and water permeability of around 15 m(3)h(-1) m(-2) bar(-1). Such materials could be of great interest in the supports fabrication for membrane application, for instance, water filtration. (C) 2021 SECV. Published by Elsevier Espana, S.L.U.Article Citation - WoS: 8Citation - Scopus: 8Pore Connectivity Effects on the Internal Surface Electric Charge of Mesoporous Silica(Springer, 2019) Şen, Tümcan; Barışık, MuratNano-scale confinements within mesoporous systems develop overlapping electric double layers (EDL) such that the existing theoretical models cannot predict the electric potential distributions and resulting surface charges. In addition, ionic conditions undergo local variation through connections between the pore voids and pore throats. For the first time in literature, we studied the charging behavior of mesoporous silica in terms of the pore to throat size ratio (R-pt) to characterize the pore connectivity effects, in addition to porosity (epsilon) and pore size (H). Both local and average surface charge densities inside mesoporous silica were examined by varying these parameters systematically. Results showed that the magnitude of surface charge density decreased with increasing EDL overlap and decreasing connectivity effects. We formulized this behavior and developed an extended model to predict mesoporous silica's internal charge as a function of porosity, pore size, and pore to throat size ratio.Article Citation - WoS: 3Citation - Scopus: 3Feasible Packing of Granular Materials in Discrete-Element Modelling of Cone-Penetration Testing(Taylor and Francis Ltd., 2018) Ecemiş, Nurhan; Bakunowicz, PaulinaThis paper explores how the discrete-element method (DEM) was found to play an increasingly important role in cone penetration test (CPT) where continuum-mechanics-based analysis tools are insufficient. We investigated several crucial features of CPT simulations in the two-dimensional DEM. First, the microparameters (stiffness and friction) of discrete material tailored to mimic clean, saturated sand, which is used in cone-penetration tests, were calibrated by curve-fitting drained triaxial tests. Then, three series of cone-penetration simulations were conducted to explore (1) top boundary conditions, (2) reasonable size of discrete particles at different initial porosities, and (3) limit initial porosity of the model for a balance between accurate representation and computational efficiency. Further, we compared the cone-penetration resistance obtained in the laboratory and numerical simulations for the range of relative densities.Article Citation - WoS: 61Citation - Scopus: 74Production of Anorthite Refractory Insulating Firebrick From Mixtures of Clay and Recycled Paper Waste With Sawdust Addition(Elsevier Ltd., 2012) Sütçü, Mücahit; Akkurt, Sedat; Bayram, Alican; Uluca, UluçProduction of porous anorthite refractory insulating firebricks from mixtures of two different clays (K244 clay and fireclay), recycled paper processing waste and sawdust addition are investigated. Suitability of alkali-containing-clay, low-alkali fireclay, pore-making paper waste and sawdust in the products was evaluated. Prepared slurry mixtures were shaped, dried and fired. Highly porous anorthite ceramics from the mixtures with up to 30% sawdust addition were successfully produced. Physical properties such as bulk density, apparent porosity, percent linear change were investigated as well as the mechanical strengths and thermal conductivity values of the samples. Thermal conductivities of the samples produced from fireclay and recycled paper waste decreased from 0.25 W/mK (1.12 g/cm 3) to 0.13 W/mK (0.64 g/cm 3) with decreasing density. Samples were stable at high temperatures up to 1100 °C, and their cold strength was sufficiently high. The porous anorthite ceramics produced in this study can be used for insulation in high temperature applications. © 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved.Article Citation - WoS: 81Citation - Scopus: 97Utilization of Recycled Paper Processing Residues and Clay of Different Sources for the Production of Porous Anorthite Ceramics(Elsevier Ltd., 2010) Sütçü, Mücahit; Akkurt, SedatProduction of porous anorthite ceramics from mixtures of paper processing residues and three different clays are investigated. Suitability of three different clays such as enriched clay, commercial clay and fireclay for manufacturing of anorthite based lightweight refractory bricks was studied. Porous character to the ceramic was provided by addition of paper processing residues (PPR). Samples with 30-40wt% PPR fired at 1200-1400°C contained anorthite (CaO·Al2O3·2SiO2) as major phase and some minor secondary phases such as mullite (3Al2O3·2SiO2) or gehlenite (2CaO·Al2O3·SiO2), depending on the calcite to clay ratio. Anorthite formation for all clay types was quite successful in samples with 30-40wt% of paper residues fired at 1300°C. A higher firing temperature of 1400°C was needed for the fireclay added samples to produce a well sintered product with large pores. Gehlenite phase occurred mostly at lower temperatures and in samples containing higher amount of calcium (50wt% PPR). Compressive strength of compacted and fired pellets consisting of mainly anorthite ranged from 8 to 43MPa. © 2010 Elsevier Ltd.Article Citation - WoS: 300Citation - Scopus: 343The Use of Recycled Paper Processing Residues in Making Porous Brick With Reduced Thermal Conductivity(Elsevier Ltd., 2009) Sütçü, Mücahit; Akkurt, SedatProduction of porous and light-weight bricks with reduced thermal conductivity and acceptable compressive strength is accomplished. Paper processing residues were used as an additive to an earthenware brick to produce the pores. SEM-EDS, XRD, XRF and TG-DTA analysis of the paper waste and brick raw material were performed. Mixtures containing brick raw materials and the paper waste were prepared at different proportions (up to 30 wt%). The granulated powder mixtures were compressed in a hydraulic press, and the green bodies were dried before firing at 1100 °C. Dilatometric behaviours, drying and firing shrinkages were investigated as well as the loss on ignition, bulk density, apparent porosity, water absorption and thermal conductivity values of the fired samples. Their mechanical and microstructural properties were also investigated. The results obtained showed that the use of paper processing residues decreased the fired density of the bricks down to 1.28 g/cm3. Compressive strengths of the brick samples produced in this study were higher than that required by the standards. Thermal conductivity of the porous brick produced in this study (<0.4 W/m K) showed more than 50% reduction compared to local brick of the same composition (0.8 W/m K). Conversion of this product to a perforated brick may reduce its thermal conductivity to very low values. Successful preliminary tests were conducted on an industrial scale.Article Citation - WoS: 11Citation - Scopus: 18Ann Model for Prediction of Powder Packing(Elsevier Ltd., 2007) Sütçü, Mücahit; Akkurt, SedatA multilayer feed forward backpropagation (MFFB) learning algorithm was used as an artificial neural network (ANN) tool to predict packing of fused alumina powder mixtures of three different sizes in green state. The data used in model construction were collected by mixing and pressing powders with average particle sizes of 350, 30 and 3 μm and with narrow particle size distributions. The data sets that were composed of green densities of cylindrical pellets were first randomly partitioned into two for training and testing of the ANN models. Based on the training data an ANN model of the packing efficiencies was created with low average error levels (3.36%). Testing of the model was also performed with successfully good average error levels of 3.39%.Article Citation - WoS: 16Citation - Scopus: 17Porous Nanocomposites Prepared From Layered Clay and Pmma [poly(methyl Methacrylate)](Elsevier Ltd., 2007) Tanoğlu, Metin; Ergün, YeldaThe aim of the present work is the preparation of PMMA based porous nanocomposites that contain clay (montmorillonite, MMT) platelets as reinforcements within the cell walls of the porous structure. To render the clay layers organophilic, MMT was surface treated by an ion exchange reaction between interlayer cations of the clay and ammonium ions of a surfactant. Clay/PMMA based porous nanocomposites were prepared by polymerization of water-in-oil emulsions with and without clay addition. The microstructure and compressive mechanical behavior of the nanocomposites were investigated. The results of mechanical tests showed that the porous systems with the addition of 1 wt.% of organoclay (OMMT) exhibited a 90% and 50% increase of collapse stress and elastic modulus values, respectively, as compared to neat porous PMMA.Article Citation - WoS: 36Citation - Scopus: 38Investigation on Glassy Skin Formation of Porous Polystyrene Fibers Electrospun From Dmf(BME-PT, 2010) Demir, Mustafa MuammerMicrometer and submicrometer diameter of polystyrene (PS) fibers were electrospun from various dimethyl formamide (DMF) solutions at different weight fractions under 35% relative humidity. Increasing polymer fraction in the solution results in a gradual morphological transition from beads-with-incipient to bead-free fibers and also increases the diameter. The formation of uniform glassy skin presumably due to radial capillary flow within the liquid jet was confirmed by scanning electron microscope. The thickness of the skin varies with the weight fraction of PS; therefore, it was normalized with respect to average fiber diameter (AFD). The skin gets thinner as the weight fraction of PS increases. In addition, the fibers exhibit highly porous internal structure and smooth surface along with slight porosity. The development of porosity is attributed to liquid-liquid phase separation of water molecules in atmospheric moisture and DMF.