Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 2Citation - Scopus: 2Sintering Under High Heating Rates(Annual Reviews, 2025) Karacasulu, Levent; Maniere, Charles; Vakifahmetoglu, Cekdar; Marinel, Sylvain; Biesuz, MattiaRapid sintering using a high heating rate is growing in technological and scientific interest. This is motivated by the promise of reducing the carbon footprint of sintering and developing materials with properties and microstructures different from those achievable by conventional heating. For instance, rapid heating can induce suppression of grain growth, the possibility of obtaining modified space charges and elemental segregations, and the development of out-of-equilibrium materials. Severe challenges still exist for the industrial exploitation of rapid sintering technologies, and, nowadays, only fast firing can be considered mature. Most of these limitations are related to the homogeneity of the sample and the possibility of obtaining complex shapes. This review investigates developments in rapid sintering by comparing different processes, suggested mechanisms, and future challenges.Article Citation - WoS: 1Citation - Scopus: 1Fast Firing Technique for Martian Regolith Simulant: Advancing Isru Capabilities(Academic Press inc Elsevier Science, 2025) Karacasulu, Levent; Tomasini, Alessandro; Vakifahmetoglu, Cekdar; Biesuz, MattiaIn-Situ Resource Utilization (ISRU) approaches hold significant importance in plans for space colonization. This work explores a different ISRU concept applying fast-firing, a robust and well-known industrial process, to Mars regolith simulant (MGS-1). The fast-fired specimens were compared to the ones obtained by conventional sintered under low heating rates. When the holding time at the firing temperature is longer than 15 min, fast-fired specimens exhibited higher density and flexural strength (> 35 MPa) than conventional sintering. For both processes, the bulk density values and the mechanical properties of the regolith compacts were enhanced with increasing dwell time. This was attributed to higher heating rates changing the densification/crystallization kinetics involving the basalt glass in the regolith composition. Specifically, high heating rate promotes sintering over crystallization. On these bases, fast firing can be considered a potential candidate for ISRU on Mars.Article Citation - WoS: 5Citation - Scopus: 5Ultrafast High-Temperature Sintering of Yttria-Stabilized Zirconia in Reactive N<sub>2</Sub> Atmosphere(Elsevier Sci Ltd, 2025) Karacasulu, Levent; de Beauvoir, Thomas Herisson; De Bona, Emanuele; Cassetta, Michele; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.; Biesuz, MattiaSo far, ultrafast high-temperature sintering (UHS) has always been carried out in an inert environment. In the present work, we investigated UHS of 3YSZ in nitrogen and argon atmosphere showing that "the atmosphere matters". Highly densified samples can be obtained in both environments but densification and grain growth are significantly retarded in N-2. Moreover, the phase evolution is strongly atmosphere-dependent with the samples treated in Ar remaining tetragonal and those treated under N-2 progressively reducing their tetragonality, eventually converting into cubic zirconia and rock salt oxynitride. The results can be explained by the incorporation of nitrogen within the ZrO2 lattice. Electrochemical impedance spectroscopy demonstrates that while the ionic bulk conductivity are marginally influenced by the sintering atmosphere, the grain boundaries' capacitive behavior strongly changes. After UHS under 30 A, excellent ionic conductors were obtained without substantial grain boundary-blocking effects.Article Citation - WoS: 13Citation - Scopus: 13On the Temperature Measurement During Ultrafast High-Temperature Sintering (uhs): Shall We Trust Metal-Shielded Thermocouples?(Elsevier Sci Ltd, 2024) Biesuz, Mattia; Karacasulu, Levent; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.Temperature measurement upon ultrafast high-temperature sintering (UHS) is a crucial task. Herein, we provide some arguments posing concerns about the use of metal-shielded thermocouples as temperature probes in UHS. The discussion is based on literature data and on some ad hoc experiments. In detail, we show at least two cases in the literature where the use of a shielded thermocouple causes a substantial underestimation of the UHS temperature. The argumentation is based on comparing the thermocouples read and the observed phase and microstructural evolution. Moreover, by means of a simple experimental design, we show that a metal shield on the thermocouple tip can substantially reduce the measured temperature. Since the metal shield is orders of magnitude more thermally conductive than the graphite felt used as heating element in UHS, it efficiently removes heat from the thermocouple tip region. As such, data acquired from shielded thermocouples must be treated with care.Article Citation - WoS: 5Citation - Scopus: 6Formation of Monolithic Srtio3-Tio2 Ceramic Heterostructures by Reactive Hydrothermal Sintering(Elsevier, 2023) Karacasulu, Levent; Kartal, Uğur; İçin, Öykü; Bortolotti, Mauro; Biesuz, Mattia; Ahmetoğlu, Çekdar VakıfIn a one-pot approach, monolithic SrTiO3-TiO2 ceramic heterostructures were obtained using the reactive hydrothermal liquid phase densification (rHLPD). Structural, morphological, and photocatalytic properties of the obtained ceramics were analyzed. The relative density of the formed components reached about 80% with reaction time, temperature, and NaOH concentration variation. It was observed via Rietveld refinement that there was no XRD detectable phase other than TiO2 and SrTiO3 in the final structure. The monolithic SrTiO3-TiO2 ceramics obtained by hydrothermal reaction at 120 °C for 24 h in 1 M NaOH concentration showed a dielectric constant being around 500, and the dielectric loss was below 0.25 at frequencies higher than 10 kHz. The SrTiO3-TiO2 heterostructured monoliths having only 20 vol% total porosity and low specific surface area, demonstrated ∼60% efficiency (in 5 h) in degrading Methylene Blue photo-catalytically. © 2023 Elsevier LtdArticle Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.