Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
11 results
Search Results
Now showing 1 - 10 of 11
Article Citation - WoS: 2Citation - Scopus: 2Sintering Under High Heating Rates(Annual Reviews, 2025) Karacasulu, Levent; Maniere, Charles; Vakifahmetoglu, Cekdar; Marinel, Sylvain; Biesuz, MattiaRapid sintering using a high heating rate is growing in technological and scientific interest. This is motivated by the promise of reducing the carbon footprint of sintering and developing materials with properties and microstructures different from those achievable by conventional heating. For instance, rapid heating can induce suppression of grain growth, the possibility of obtaining modified space charges and elemental segregations, and the development of out-of-equilibrium materials. Severe challenges still exist for the industrial exploitation of rapid sintering technologies, and, nowadays, only fast firing can be considered mature. Most of these limitations are related to the homogeneity of the sample and the possibility of obtaining complex shapes. This review investigates developments in rapid sintering by comparing different processes, suggested mechanisms, and future challenges.Article Citation - WoS: 1Citation - Scopus: 1Fast Firing Technique for Martian Regolith Simulant: Advancing Isru Capabilities(Academic Press inc Elsevier Science, 2025) Karacasulu, Levent; Tomasini, Alessandro; Vakifahmetoglu, Cekdar; Biesuz, MattiaIn-Situ Resource Utilization (ISRU) approaches hold significant importance in plans for space colonization. This work explores a different ISRU concept applying fast-firing, a robust and well-known industrial process, to Mars regolith simulant (MGS-1). The fast-fired specimens were compared to the ones obtained by conventional sintered under low heating rates. When the holding time at the firing temperature is longer than 15 min, fast-fired specimens exhibited higher density and flexural strength (> 35 MPa) than conventional sintering. For both processes, the bulk density values and the mechanical properties of the regolith compacts were enhanced with increasing dwell time. This was attributed to higher heating rates changing the densification/crystallization kinetics involving the basalt glass in the regolith composition. Specifically, high heating rate promotes sintering over crystallization. On these bases, fast firing can be considered a potential candidate for ISRU on Mars.Article Citation - WoS: 5Citation - Scopus: 5Ultrafast High-Temperature Sintering of Yttria-Stabilized Zirconia in Reactive N<sub>2</Sub> Atmosphere(Elsevier Sci Ltd, 2025) Karacasulu, Levent; de Beauvoir, Thomas Herisson; De Bona, Emanuele; Cassetta, Michele; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.; Biesuz, MattiaSo far, ultrafast high-temperature sintering (UHS) has always been carried out in an inert environment. In the present work, we investigated UHS of 3YSZ in nitrogen and argon atmosphere showing that "the atmosphere matters". Highly densified samples can be obtained in both environments but densification and grain growth are significantly retarded in N-2. Moreover, the phase evolution is strongly atmosphere-dependent with the samples treated in Ar remaining tetragonal and those treated under N-2 progressively reducing their tetragonality, eventually converting into cubic zirconia and rock salt oxynitride. The results can be explained by the incorporation of nitrogen within the ZrO2 lattice. Electrochemical impedance spectroscopy demonstrates that while the ionic bulk conductivity are marginally influenced by the sintering atmosphere, the grain boundaries' capacitive behavior strongly changes. After UHS under 30 A, excellent ionic conductors were obtained without substantial grain boundary-blocking effects.Article Citation - WoS: 13Citation - Scopus: 13On the Temperature Measurement During Ultrafast High-Temperature Sintering (uhs): Shall We Trust Metal-Shielded Thermocouples?(Elsevier Sci Ltd, 2024) Biesuz, Mattia; Karacasulu, Levent; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.Temperature measurement upon ultrafast high-temperature sintering (UHS) is a crucial task. Herein, we provide some arguments posing concerns about the use of metal-shielded thermocouples as temperature probes in UHS. The discussion is based on literature data and on some ad hoc experiments. In detail, we show at least two cases in the literature where the use of a shielded thermocouple causes a substantial underestimation of the UHS temperature. The argumentation is based on comparing the thermocouples read and the observed phase and microstructural evolution. Moreover, by means of a simple experimental design, we show that a metal shield on the thermocouple tip can substantially reduce the measured temperature. Since the metal shield is orders of magnitude more thermally conductive than the graphite felt used as heating element in UHS, it efficiently removes heat from the thermocouple tip region. As such, data acquired from shielded thermocouples must be treated with care.Article Citation - WoS: 9Citation - Scopus: 9Cold Sintering Assisted Two-Step Sintering of Potassium Sodium Niobate (knn) Ceramics(Elsevier, 2023) Karacasulu, Levent; Ahmetoğlu, Çekdar VakıfPotassium sodium niobate (KNN) ceramics were densified using a multiple-stage sintering process in which initially applied cold sintering process (CSP) was followed by the solid-state sintering between 1100 and 1120 °C. Comparative assessments demonstrated that multi-step sintered samples yielded better properties than conventionally sintering ones. The highest relative density (94.7%) and the best electrical properties were obtained from the sample subjected to cold sintering at 120 °C/1 h using 5 wt% deionized water subsequently heat-treated at 1120 °C/2 h, resulting in a monolithic KNN ceramic having a piezoelectric coefficient of 120 pC/N. © 2023 Elsevier B.V.Article Citation - WoS: 5Citation - Scopus: 6Formation of Monolithic Srtio3-Tio2 Ceramic Heterostructures by Reactive Hydrothermal Sintering(Elsevier, 2023) Karacasulu, Levent; Kartal, Uğur; İçin, Öykü; Bortolotti, Mauro; Biesuz, Mattia; Ahmetoğlu, Çekdar VakıfIn a one-pot approach, monolithic SrTiO3-TiO2 ceramic heterostructures were obtained using the reactive hydrothermal liquid phase densification (rHLPD). Structural, morphological, and photocatalytic properties of the obtained ceramics were analyzed. The relative density of the formed components reached about 80% with reaction time, temperature, and NaOH concentration variation. It was observed via Rietveld refinement that there was no XRD detectable phase other than TiO2 and SrTiO3 in the final structure. The monolithic SrTiO3-TiO2 ceramics obtained by hydrothermal reaction at 120 °C for 24 h in 1 M NaOH concentration showed a dielectric constant being around 500, and the dielectric loss was below 0.25 at frequencies higher than 10 kHz. The SrTiO3-TiO2 heterostructured monoliths having only 20 vol% total porosity and low specific surface area, demonstrated ∼60% efficiency (in 5 h) in degrading Methylene Blue photo-catalytically. © 2023 Elsevier LtdArticle Citation - WoS: 28Citation - Scopus: 33Cold Sintering as a Promising Isru Technique: a Case Study of Mars Regolith Simulant(Elsevier, 2023) Karacasulu, Levent; Karl, David; Gurlo, Aleksander; Ahmetoğlu, Çekdar VakıfMars regolith simulant (MGS-1) was densified for the first time via a cold sintering process (CSP) as a novel in-situ resource utilization (ISRU) concept. The technique comprises the utilization of NaOH solution as a liquid media during the densification of simulant powder with <100 μm particle size. In as short as 30 min, with the increase in the NaOH concentration (from 3 M to 10 M) and processing temperature (from 150 °C to 250 °C), the relative densities of the regolith compacts and the mechanical properties were enhanced. The artifacts produced with Mars regolith simulant powder at 250 °C using 10 M NaOH solution yielded a relative density of around 88% and compressive strength reaching ∼45 MPa.Article Citation - WoS: 7Citation - Scopus: 7Hydrothermal Synthesis of Potassium–sodium Niobate Powders(Wiley, 2022) Pişkin, Cerem; Karacasulu, Levent; Ischia, Gloria; Bortolotti, Mauro; Ahmetoğlu, Çekdar VakıfPotassium–sodium niobates (KxNa1−xNbO3, 0 < x < 1, KNN) were hydrothermally synthesized under varying alkaline ratios (K+/Na+), total hydroxide concentration, reaction temperature, and time. Compositional surveys were developed by using Rietveld analyses derived quantitative volume fractions. The data demonstrated that phase pure KNN synthesis can be achieved by reacting the niobium source with the hydroxide solution having 6 M total hydroxide concentration, cation ratio (K+/Na+) of above 6 at temperatures ≥200°C for 24 h. Dissolution–precipitation events through intermediate products including hexaniobates were postulated as a plausible formation mechanism. It was shown also that the single-phase KNN approaching the morphotropic phase boundary (MPB) could be obtained by further incorporation of sodium ions into the crystal via post-annealing at 800°C/2 h, following the hydrothermal synthesis.Article Citation - WoS: 8Citation - Scopus: 12Synthesis of Potassium-Sodium Niobate (Knn) From Nbo2(Elsevier, 2021) Piskin, Cerem; Karacasulu, Levent; Bortolotti, Mauro; Vakifahmetoglu, CekdarKxNa1-xNbO3 (0 < x < 1) were synthesized via hydrothermal method using niobium dioxide (NbO2) as the niobium source instead of the most common one, Nb2O5. Potassium-rich KxNa1-xNbO3 (x > 0.5) was obtained from 8 M total hydroxide concentration after 6 h of reaction at 200 degrees C. Rietveld refinement of the XRD data revealed that all samples exhibited the secondary NaNbO3 phase. However, the lowest amount (3.74 vol%) was obtained for 24 h of reaction under 10 M alkaline solution. After 3 h of reaction, dodecahedra shaped hexaniobate phase (KxNa8-xNb6O19.nH(2)O) was observed. Those structures were, subsequently, replaced by similar to 3 mu m cube shaped KNN crystals, obtained under 10 M reaction in 24 h time period.Article Citation - WoS: 103Citation - Scopus: 110Cold Sintering of Ceramics and Glasses: a Review(Elsevier Ltd., 2020) Ahmetoğlu, Çekdar Vakıf; Karacasulu, LeventTraditionally ceramic artifacts are processed at high temperatures (> 1000 degrees C) by classical sintering techniques such as solid state, liquid phase and pressure-assisted sintering. Recently, inspired from the geology, novel sintering approaches that allow the densification of ceramic components at relatively low temperatures <= 400 degrees C have been proposed. While initial efforts for such low temperature densification concept were developed in the mid-70s, the topic has become increasingly prominent in the last decade. Currently, these low temperature methods can be classified into four main groups: (i) hydrothermal reaction sintering (HRS), (ii) hydrothermal hot pressing (HHP), (iii) pressure-assisted densification techniques: room-temperature densification (RTD), cold sintering (CS), warm press (WP), and finally no-pressure assisted method called (iv) reactive hydrothermal liquid phase densification (rHLPD). Above named techniques are commonly assisted by an aqueous solution used as either reactant or transient liquid phase to assist densification. Starting from the background in traditional sintering processes, this review aims to explore in depth the existing literature about low temperature densification approaches along with their advantages & disadvantages, and probable application areas.