Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 42Citation - Scopus: 46Importance of Cds Buffer Layer Thickness on Cu2znsns4-Based Solar Cell Efficiency(IOP Publishing Ltd., 2018) Cantaş, Ayten; Türkoğlu, Fulya; Meriç, Ece; Akça, Fatime Gülşah; Özdemir, Mehtap; Tarhan, Enver; Özyüzer, Lütfi; Özyüzer, Gülnur AygünCu2ZnSnS4 (CZTS) thin films were grown on Mo-coated soda lime glass (SLG) substrates by the sulfurization of DC magnetron-sputtered Zn, Sn and Cu metallic precursors under a sulfur atmosphere at 550 °C for 45 min. Understanding the composition and structure of the CZTS absorber layer is necessary to obtain efficient solar cells. With this aim, x-ray diffractometry, Raman spectroscopy, scanning electron microscopy, energy dispersive spectroscopy and x-ray photoelectron spectroscopy were used to investigate the CZTS absorber layers. CZTS absorber films were obtained and found to be Cu-poor and Zn-rich in composition, which are both qualities desired for efficient solar cells. CdS was used as a buffer layer and was grown by the chemical bath deposition technique. The optical properties of CdS films on SLG were searched for using a spectroscopic ellipsometer and the results revealed that the bandgap increases with film thickness increment. CZTS-based solar cells with different CdS buffer layer thicknesses were prepared using a SLG/Mo/CZTS/CdS/ZnO/AZO solar cell configuration. The influence of the CdS buffer layer thickness on the performance of the CZTS solar cells was investigated. Device analysis showed that electrical characteristics of solar cells strongly depend on the buffer layer's thickness. Highly pronounced changes in V OC, fill factor and J SC parameters, which are the main efficiency limiting factors, with changing buffer layer thicknesses were observed. Our experiments confirmed that decreasing the CdS thickness improved the efficiency of CZTS solar cells down to the lowest thickness limit.Article Citation - WoS: 2Citation - Scopus: 2Comparison of Photocatalytic Properties of Tio2 Thin Films and Fibers(EDP Sciences, 2016) Özdemir, Mehtap; Kurt, Metin; Özyüzer, Lütfi; Aygün, GülnurEfficiency of solar panels degrades as a result of organic contamination such as airborne particles, bird droppings and leaves. Any foreign object on photovoltaic panels reduces the sunlight entering the absorbing surface of the solar panels. Since this leads to a major problem decreasing in energy production, solar panels should be cleaned. The self-cleaning method can be preferred. There are some methods to clean the surface of solar panels. Among the self-cleaning materials, TiO2 is the most preferable ones because of its powerful photocatalytic properties. In this study, photocatalytic TiO2 were produced in two different nanostructures: nanofibers and thin films. TiO2 nanofibers were successfully produced by electrospinning. TiO2 thin films were fabricated by reactive magnetron sputtering technique. Both TiO2 nanofiber and thin film structures were heat-treated to form TiO2 in anatase phase at 600 °C for 2 h in air. Then, they were evaluated by SEM analyses for morphology, X-ray diffraction (XRD) analyses for phase structures, X-ray photoelectron spectroscopy (XPS) for the chemical state and atomic concentration, and UV-spectrometer for photocatalytic performance. The results indicate that photocatalytic and transmittance properties of TiO2 thin films are better than those of nanofibers. Consequently, TiO2 based thin films exhibit better performance for solar cell applications due to the surface cleanliness.Article Citation - WoS: 42Citation - Scopus: 44Growth of Cu2znsns4 Absorber Layer on Flexible Metallic Substrates for Thin Film Solar Cell Applications(Elsevier Ltd., 2015) Yazıcı, Şebnem; Olgar, Mehmet Ali; Akça, Fatime Gülşah; Cantaş, Ayten; Kurt, Metin; Aygün, Gülnur; Tarhan, Enver; Yanmaz, Ekrem; Özyüzer, LütfiIn this work, Cu2ZnSnS4 (CZTS) absorber layers were fabricated using a two-stage process. Sequentially deposited Cu-Zn-Sn thin film layers on metallic foils were annealed in an Ar + S2(g) atmosphere. We aimed to investigate the role of flexible titanium and molybdenum foil substrates in the growth mechanism of CZTS thin films. The Raman spectra and X-ray photoelectron spectroscopy analyses of the sulfurized thin films revealed that, except for the presence of Sn-based secondary phases, nearly pure CZTS thin films were obtained. Additionally, the intense and sharp X-ray diffraction peak from the (112) plane provided evidence of good crystallinity. Electron dispersive spectroscopy analysis indicated sufficient sulfur content but poor Zn atomic weight percentage in the films. Absorption and band-gap energy analyses were carried out to confirm the suitability of CZTS thin films as the absorber layer in solar cell applications. Hall effect measurements showed the p-type semiconductor behavior of the CZTS samples. Moreover, the back contact behavior of these metallic flexible substrates was investigated and compared. We detected formation of cracks in the CZTS layer on the molybdenum foils, which indicates the incompatibility of molybdenum's thermal expansion coefficient with the CZTS structure. We demonstrated the application of the magnetron sputtering technique for the fabrication of CZTS thin films on titanium foils having lightweight, flexible properties and suitable for roll-to-roll manufacturing for high throughput fabrication. Titanium foils are also cost competitive compared to molybdenum foils. © 2015 Elsevier B.V.