Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

2022 - 20233

Settings

Author: search.filters.author.Ahmetoğlu, Çekdar VakıfPublication Index: search.filters.publicationIndex.PubMed

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 8
    Citation - Scopus: 8
    Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels
    (American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar Vakıf
    This work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.
  • Article
    Citation - WoS: 18
    Citation - Scopus: 22
    Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes
    (American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, Aleksander
    Lab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.
  • Article
    Citation - WoS: 8
    Citation - Scopus: 11
    Spreadability of Metal Powders for Laser-Powder Bed Fusion Via Simple Image Processing Steps
    (MDPI, 2022) Ahmetoğlu, Çekdar Vakıf; Hasdemir, Beyza; Biasetto, Lisa
    This paper investigates the spreadability of the spherical CoCrWMo powder for laser- powder bed fusion (PBF-LB) by using image processing algorithms coded in MATLAB. Besides, it also aims to examine the spreadability dependence with the other characteristics such as powder size distribution, apparent density, angle of repose. Powder blends in four different particle size distributions are prepared, characterized, and spreadability tests are performed with the PBF-LB. The results demonstrate that an increase in fine particle ratio by volume (below 10 µm) enhances the agglomeration and decreases the flowability, causing poor spreadability. These irregularities on the spread layers are quantified with simple illumination invariant analysis. A clear relation between powder spreadability and 3D printed structures properties in terms of residual porosity could not be defined since structural defects in 3D printed parts also depends on other processing parameters such as spatter formation or powder size over layer height ratio.