Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
20 results
Search Results
Now showing 1 - 10 of 20
Article Citation - WoS: 11Citation - Scopus: 13Magnesium-Ion Battery Anode From Polymer-Derived Sioc Nanobeads(Wiley, 2023) Guo, Wuqi; Kober, Delf; Gurlo, Aleksander; Bekheet, Maged F.; İçin, Öykü; Ahmetoğlu, Çekdar VakıfTin-containing silicon oxycarbide (SiOC/Sn) nanobeads are synthesized with different carbon/tin content and tested as electrodes for magnesium-ion batteries. The synthesized ceramics are characterized by thermogravimetric-mass spectroscopy, Fourier-transform infrared spectroscopy, X-ray diffraction (XRD), Raman spectroscopy, N2 sorption analysis, scanning electron microscope, energy-dispersive X-ray, and elemental analysis. Galvanostatic cycling tests, rate performance tests, electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) tests, and ex situ XRD measurements are conducted. Results of battery performance tests present a high capacity of 198.2 mAh g-1 after the first discharging and a reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1. Excellent rate performance efficiency of 85.2% is achieved. Battery performances in this research are influenced by surface area, and tin contentof the SiOC/Sn nanobeads. EIS, CV tests, and ex situ XRD measurements reveal that higher surface area contributes to higher capacity by providing more accessible Mg2+ ion storage sites and higher rate capability by improving the diffusion process. Higher Sn content increases battery capacity through reversible Mg-Mg2Sn-Mg alloying/dealloying process and improves the rate performances by increasing electrical conductivity. Besides, SiOC advances cycling stability by preventing electrode collapse and enhances the capacity due to higher surface capacitive effects. SiOC nanobeads containing Sn nanoparticles are synthesized and tested as anode for magnesium-ion batteries. The anodes show high performance with reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1 and excellent rate performance efficiency of 85.2% from 50 to 500 mA g-1.imageArticle Citation - WoS: 8Citation - Scopus: 8Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels(American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar VakıfThis work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.Article Citation - WoS: 9Citation - Scopus: 9Cold Sintering Assisted Two-Step Sintering of Potassium Sodium Niobate (knn) Ceramics(Elsevier, 2023) Karacasulu, Levent; Ahmetoğlu, Çekdar VakıfPotassium sodium niobate (KNN) ceramics were densified using a multiple-stage sintering process in which initially applied cold sintering process (CSP) was followed by the solid-state sintering between 1100 and 1120 °C. Comparative assessments demonstrated that multi-step sintered samples yielded better properties than conventionally sintering ones. The highest relative density (94.7%) and the best electrical properties were obtained from the sample subjected to cold sintering at 120 °C/1 h using 5 wt% deionized water subsequently heat-treated at 1120 °C/2 h, resulting in a monolithic KNN ceramic having a piezoelectric coefficient of 120 pC/N. © 2023 Elsevier B.V.Article Citation - WoS: 5Citation - Scopus: 6Formation of Monolithic Srtio3-Tio2 Ceramic Heterostructures by Reactive Hydrothermal Sintering(Elsevier, 2023) Karacasulu, Levent; Kartal, Uğur; İçin, Öykü; Bortolotti, Mauro; Biesuz, Mattia; Ahmetoğlu, Çekdar VakıfIn a one-pot approach, monolithic SrTiO3-TiO2 ceramic heterostructures were obtained using the reactive hydrothermal liquid phase densification (rHLPD). Structural, morphological, and photocatalytic properties of the obtained ceramics were analyzed. The relative density of the formed components reached about 80% with reaction time, temperature, and NaOH concentration variation. It was observed via Rietveld refinement that there was no XRD detectable phase other than TiO2 and SrTiO3 in the final structure. The monolithic SrTiO3-TiO2 ceramics obtained by hydrothermal reaction at 120 °C for 24 h in 1 M NaOH concentration showed a dielectric constant being around 500, and the dielectric loss was below 0.25 at frequencies higher than 10 kHz. The SrTiO3-TiO2 heterostructured monoliths having only 20 vol% total porosity and low specific surface area, demonstrated ∼60% efficiency (in 5 h) in degrading Methylene Blue photo-catalytically. © 2023 Elsevier LtdArticle Citation - WoS: 3Citation - Scopus: 2Targeted Multidrug Delivery Systems To Kill Antibiotic-Resistant Staphylococcus Aureus(Editions de Sante, 2023) Özalp, Veli Cengiz; Ucak, Samet; Dursun, Ali D.; Sudağıdan, Mert; İçin, Öykü; Ahmetoğlu, Çekdar Vakıf; Henning, Laura M.; Simon, Ulla; Gurlo, AleksanderDifferent ordered mesoporous silica (OMS) nanoparticles, ranging from regular COK-12 to COK-12 modified in terms of pore shape and size, have been employed as standard drug carriers for the controlled adsorption and release of drug molecules in comparison to well-known OMS SBA-15 and MCM-41. The cytotoxicity analysis demonstrated that regular COK-12 particles were less harmful to mammalian cultured cells, causing lower apoptosis induction than modified COK-12, MCM-41, and SBA-15 particles. Thus, regular COK-12 was further used to prepare a dual antibiotic-loaded drug delivery material, followed by surface functionalization with Staphylococcus aureus-specific aptamers for targeting. The results demonstrated that the joint loading of lysozyme and vancomycin in regular COK-12 improved the ability of the antibiotic treatments to kill methicillin-resistant Staphylococcus strains via aptamer targeting. The minimum inhibitory concentration (MIC) values decreased 4.1-fold and 12-fold compared to the non-targeted use of the antimicrobial agents in homogeneous solutions for vancomycin and lysozyme, respectively, clearly demonstrating the high potential of COK-12 to be used as a carrier in multidrug therapy. © 2023 Elsevier B.V.Article Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.Article Citation - WoS: 28Citation - Scopus: 33Cold Sintering as a Promising Isru Technique: a Case Study of Mars Regolith Simulant(Elsevier, 2023) Karacasulu, Levent; Karl, David; Gurlo, Aleksander; Ahmetoğlu, Çekdar VakıfMars regolith simulant (MGS-1) was densified for the first time via a cold sintering process (CSP) as a novel in-situ resource utilization (ISRU) concept. The technique comprises the utilization of NaOH solution as a liquid media during the densification of simulant powder with <100 μm particle size. In as short as 30 min, with the increase in the NaOH concentration (from 3 M to 10 M) and processing temperature (from 150 °C to 250 °C), the relative densities of the regolith compacts and the mechanical properties were enhanced. The artifacts produced with Mars regolith simulant powder at 250 °C using 10 M NaOH solution yielded a relative density of around 88% and compressive strength reaching ∼45 MPa.Article Citation - WoS: 9Citation - Scopus: 9Polymer-derived ceramic molten metal filters(Springer, 2022) Dizdar, Kerem Can; Kulkarni, Apoorv; Dışpınar, Derya; Soraru, Gian Domenico; Ahmetoğlu, Çekdar Vakıf; Semerci, TuğçeThis paper reports the synthesis and the performance of polymer-derived ceramic filters for molten metal filtration. Two different filter types were studied: foam filters produced from flexible polyurethane (PU) foams and additive manufacturing (AM) filters produced from thermoplastic polyurethane (TPU) cellular structure, and the results from all filter types were compared with that of the commercially used SiC foam filters. In both cases, the urethane-based polymeric template was impregnated with the preceramic solution, followed by pyrolysis. The produced ceramic components were then used to filter a molten Al alloy (A357), and the resulting Al samples were characterized for their mechanical properties. When filters were used, more reproducible and reliable mechanical properties were achieved compared to the samples obtained without any filtration. Among the different filters tested, the foam filters demonstrated better performance in comparison with the AM ceramic filters due probably to the three-dimensional interconnected porosity compared with the unidirectional cellular structure of the AM ceramic filters.Article Citation - WoS: 18Citation - Scopus: 22Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes(American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, AleksanderLab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.Article Citation - WoS: 8Citation - Scopus: 11Spreadability of Metal Powders for Laser-Powder Bed Fusion Via Simple Image Processing Steps(MDPI, 2022) Ahmetoğlu, Çekdar Vakıf; Hasdemir, Beyza; Biasetto, LisaThis paper investigates the spreadability of the spherical CoCrWMo powder for laser- powder bed fusion (PBF-LB) by using image processing algorithms coded in MATLAB. Besides, it also aims to examine the spreadability dependence with the other characteristics such as powder size distribution, apparent density, angle of repose. Powder blends in four different particle size distributions are prepared, characterized, and spreadability tests are performed with the PBF-LB. The results demonstrate that an increase in fine particle ratio by volume (below 10 µm) enhances the agglomeration and decreases the flowability, causing poor spreadability. These irregularities on the spread layers are quantified with simple illumination invariant analysis. A clear relation between powder spreadability and 3D printed structures properties in terms of residual porosity could not be defined since structural defects in 3D printed parts also depends on other processing parameters such as spatter formation or powder size over layer height ratio.