Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

2019 - 201912020 - 20252

Settings

Author: search.filters.author.Akkurt, SedatPublisher: search.filters.publisher.Springer

Search Results

Now showing 1 - 3 of 3
  • Article
    Deposition of (La,Sr)CoO₃-δ and (La,Sr)₂CoO₄-δ Cathode Layers on Gadolinia-Doped Ceria by Electrospray Deposition
    (Springer, 2025) Ergen, Emre; Akkurt, Sedat
    La-, Sr-, and Co-based oxides have proven their performances in the cathode layers of intermediate temperature levels of solid oxide fuel cells (SOFC), and hence have been frequently studied. They are deposited on the electrolyte layer by chemical vapor deposition (CVD), screen printing, pulsed laser deposition (PLD), etc. The electrospray deposition (ESD) proved itself as an effective and facile method for cathode deposition. Cathode layers deposited on gadolinia-doped ceria (GDC) with the compositions of (La0.5Sr0.5)CoO3, (La0.8Sr0.2)CoO3, (La0.5Sr0.5)2CoO4, and (La0.8Sr0.2)2CoO4 are known to provide low resistance values which are critical in cell performance. In this study, ESD is used for the first time as the coating method of these compositions. Area-specific resistance (ASR) measurements made by electrochemical impedance spectroscopy (EIS) showed promising results. Particularly, the sample coated in (La0.5Sr0.5)CoO3 composition showed an ASR value of 0.11 Omega.cm2 at 700 degrees C. ESD showed the ability to control the cathode coating microstructure by controlling the spraying parameters.
  • Article
    Citation - WoS: 14
    Citation - Scopus: 15
    Electrochemical Performance of La0.6sr0.4co0.2fe0.8o3-Ce0.9gd0.1o2 Composite Sofc Cathodes Fabricated by Electrocatalyst And/Or Electrocatalyst-Ionic Conductor Infiltration
    (Springer, 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, Sedat
    Infiltration of electrocatalyst precursor solutions into previously sintered porous ionic conductor scaffolds has been used recently as an alternative method to the conventional co-sintering route to fabricate electrocatalyst-ionic conductor composites for solid oxide fuel cell (SOFC) cathode applications. However, the aqueous nitrate solutions generally used to perform the infiltration process results in electrocatalyst precipitates that are disconnected from each other, yielding poor electrode performance. In this work, polymeric electrocatalyst (La0.6Sr0.4Co0.2Fe0.8O3-LSCF) precursors that produce interconnected thin films upon heat treatment were used to infiltrate porous ionic conductor Ce0.9Gd0.1O2-delta (GDC) scaffolds to overcome these issues. In addition, for the first time in the literature, a mixture of LSCF and GDC polymeric precursors, which would yield LSCF-GDC nanocomposite coatings on the grains of the porous GDC scaffold were used as the infiltration solution. Thus, further enhancement of the electrocatalyst/ionic conductor interfacial area and achievement of improved electrode performance was aimed. As a result of the optimization studies, the lowest measured area specific polarization resistance (ASR(cathode)) values of 0.47 and 0.73 omega.cm(2) were obtained for polymeric LSCF+GDC and LSCF precursor infiltrations respectively at 700 degrees C, in air. In addition, LSCF+GDC infiltration yielded electrodes with much improved long-term stability in comparison to those obtained by LSCF infiltration. [GRAPHICS] .
  • Article
    Citation - WoS: 15
    Citation - Scopus: 16
    Fabrication of Lscf and Lscf-Gdc Nanocomposite Thin Films Using Polymeric Precursors
    (Springer, 2020) Sındıraç, Can; Ahsen, Ali; Öztürk, Osman; Akkurt, Sedat; Birss, Viola, I; Büyükaksoy, Aligül
    La1-xSrxCoyFe1-yO3 (LSCF) and LSCF-gadolinia-doped ceria (LSCF-GDC) composites are used as solid oxide fuel cell (SOFC) cathodes. In the present study, to maximize the LSCF/gas and LSCF/GDC interfacial area and thus enhance the performance, we fabricated both single-phase LSCF and composite LSCF-GDC thin-film electrodes using a facile and cost-effective polymeric precursor technique. This method involves molecular level mixing of cations in solution form and results in average particle sizes of ca. 72 nm and 60 nm upon annealing at 700 degrees C, respectively. For LSCF, electrochemical impedance spectroscopy measurements indicate very low electrode polarization resistances of ca. 0.6 omega cm(2) per electrode at 600 degrees C. However, the addition of GDC results in poorer electrochemical activity but better microstructural and electrochemical stability, all at 600 degrees C. Surface analysis revealed that Fe surface segregation occurs in the single-phase LSCF, while predominantly Co segregation is observed at the LSCF-GDC composite electrode surface.