Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
21 results
Search Results
Now showing 1 - 10 of 21
Article Citation - Scopus: 3Development of Chrono-Spectral Gold Nanoparticle Growth Based Plasmonic Biosensor Platform(Elsevier, 2024) Sözmen, Alper Baran; Elveren, Beste; Erdoğan, Duygu; Mezgil, Bahadır; Baştanlar, Yalın; Yıldız, Ümit Hakan; Arslan Yıldız, AhuPlasmonic sensor platforms are designed for rapid, label-free, and real-time detection and they excel as the next generation biosensors. However, current methods such as Surface Plasmon Resonance require expertise and well-equipped laboratory facilities. Simpler methods such as Localized Surface Plasmon Resonance (LSPR) overcome those limitations, though they lack sensitivity. Hence, sensitivity enhancement plays a crucial role in the future of plasmonic sensor platforms. Herein, a refractive index (RI) sensitivity enhancement methodology is reported utilizing growth of gold nanoparticles (GNPs) on solid support and it is backed up with artificial neural network (ANN) analysis. Sensor platform fabrication was initiated with GNP immobilization onto solid support; immobilized GNPs were then used as seeds for chrono-spectral growth, which was carried out using NH2OH at varied incubation times. The response to RI change of the platform was investigated with varied concentrations of sucrose and ethanol. The detection of bacteria E.coli BL21 was carried out for validation as a model microorganism and results showed that detection was possible at 102 CFU/ml. The data acquired by spectrophotometric measurements were analyzed by ANN and bacteria classification with percentage error rates near 0% was achieved. The proposed LSPR-based, label-free sensor application proved that the developed methodology promises utile sensitivity enhancement potential for similar sensor platforms. © 2024 The Author(s)Article Citation - WoS: 1Citation - Scopus: 1The Soft Nanodots as Fluorescent Probes for Cell Imaging: Analysis of Cell and Spheroid Penetration Behavior of Single Chain Polymer Dots(Wiley, 2024) Yücel, Müge; Onbaş, Rabia; Arslan Yıldız, Ahu; Yıldız, Ümit HakanThis study describes the formation, size control, and penetration behavior of polymer nanodots (Pdots) consisting of single or few chain polythiophene-based conjugated polyelectrolytes (CPEs) via nanophase separation between good solvent and poor solvent of CPE. Though the chain singularity may be associated with dilution nanophase separation suggests that molecules of a good solvent create a thermodynamically driven solvation layer surrounding the CPEs and thereby separating the single chains even in their poor solvents. This statement is therefore corroborated with emission intensity/lifetime, particle size, and scattering intensity of polyelectrolyte in good and poor solvents. Regarding the augmented features, Pdots are implemented into cell imaging studies to understand the nuclear penetration and to differentiate the invasive characteristics of breast cancer cells. The python based red, green, blue (RGB) color analysis depicts that Pdots have more nuclear penetration ability in triple negative breast cancer cells due to the different nuclear morphology in shape and composition and Pdots have penetrated cell membrane as well as extracellular matrix in spheroid models. The current Pdot protocol and its utilization in cancer cell imaging are holding great promise for gene/drug delivery to target cancer cells by explicitly achieving the very first priority of nuclear intake. The penetration capability of cationic soft nanodots in to tumor models of breast cancer is demonstrated. The image analysis based on fluorescence intensity variation reveals the characteristics of translocation of nanodots in dense mediums such as tumor models.imageArticle Citation - WoS: 3Citation - Scopus: 4Biopatterning of 3d Cellular Model by Contactless Magnetic Manipulation for Cardiotoxicity Screening(Mary Ann Liebert, Inc, 2023) Önbaş, Rabia; Arslan Yıldız, AhuPatterning cells to create three-dimensional (3D) cell culture models by magnetic manipulation is a promising technique, which is rapid, simple, and cost-effective. This study introduces a new biopatterning approach based on magnetic manipulation of cells with a bioink that consists alginate, cells, and magnetic nanoparticles. Plackett-Burman and Box-Behnken experimental design models were used to optimize bioink formulation where NIH-3T3 cells were utilized as a model cell line. The patterning capability was confirmed by light microscopy through 7 days culture time. Then, biopatterned 3D cardiac structures were formed using H9c2 cardiomyocyte cells. Cellular and extracellular components, F-actin and collagen Type I, and cardiac-specific biomarkers, Troponin T and MYH6, of biopatterned 3D cardiac structures were observed successfully. Moreover, Doxorubicin (DOX)-induced cardiotoxicity was investigated for developed 3D model, and IC50 value was calculated as 8.1 μM for biopatterned 3D cardiac structures, which showed higher resistance against DOX-exposure compared to conventional two-dimensional cell culture. Hereby, developed biopatterning methodology proved to be a simple and rapid approach to fabricate 3D cardiac models, especially for drug screening applications. Copyright 2023, Mary Ann Liebert, Inc., publishers.Book Part Citation - Scopus: 2Bioprinting of Hydrogels for Tissue Engineering and Drug Screening Applications(Elsevier, 2022) Özmen, Ece; Yıldırım, Özüm; Arslan Yıldız, AhuIn tissue engineering, the 3-dimensional (3D) bioprinting method that enables the production of 3D structures by combining bioinks and cells has become one of the most promising technique. Over the last few years, 3D cell culture models gained importance in the development of disease model and drug development studies. The successful production of the 3D structures by 3D bioprinting mostly depends on the properties of the bioink to be used. Hydrogels, which are natural or synthetic polymers, are generally preferred as bioink materials with their high swelling ability, biocompatibility, biodegradability, and easy gelation ability. The convenience of hydrogels for varied bioprinting applications make them proper bioink materials for bioprinting of artificial tissues, tumor models, and tissue grafts. Bioprinting of functional tissues is successfully performed for years, and hydrogels are utilized as bioink in bone, vascular, neural, cartilage, cardiac, skin tissue engineering, and drug screening. In this chapter, bioprinting methodology, bioinks, hydrogel bioinks, and their applications are discussed in detail. © 2023 Elsevier Inc. All rights reserved.Article Citation - WoS: 9Citation - Scopus: 9Fabrication and Development of a Microfluidic Paper-Based Immunosorbent Assay Platform (μpisa) for Colorimetric Detection of Hepatitis C(Royal Society of Chemistry, 2023) Özefe, Fatih; Arslan Yıldız, AhuPaper-based microfluidics is an emerging analysis tool used in various applications, especially in point-of-care (PoC) diagnostic applications, due to its advantages over other types of microfluidic devices in terms of simplicity in both production and operation, cost-effectiveness, rapid response time, low sample consumption, biocompatibility, and ease of disposal. Recently, various techniques have been developed and utilized for the fabrication of paper-based microfluidics, such as photolithography, micro-embossing, wax and PDMS printing, etc. In this study, we offer a fabrication methodology for a microfluidic paper-based immunosorbent assay (μPISA) platform and the detection of Hepatitis C Virus (HCV) was carried out to validate this platform. A laser ablation technique was utilized to form hydrophobic barriers easily and rapidly, which was the major advantage of the developed fabrication methodology. The characterization of the μPISA platform was performed in terms of micro-channel properties using bright-field (BF) microscopy, and surface properties using scanning electron microscopy (SEM). At the same time, sample volume and liquid handling capacity were analyzed quantitatively. Ablation speed (S) and laser power (P) were optimized, and it was shown that one combination (10P60S) provided minimal deviation in micro-channel dimensions and prevented deterioration of hydrophobic barriers. Also, the minimum hydrophobic barrier width, which prevents cross-barrier bleeding, was determined to be 255.92 ± 10.01 μm. Furthermore, colorimetric HCV NS3 detection was implemented to optimize and validate the μPISA platform. Here, HCV NS3 in both PBS and human blood plasma was successfully detected by the naked eye at concentrations as low as 1 ng mL−1 and 10 ng mL−1, respectively. Moreover, the limit of detection (LoD) values for HCV NS3 were acquired as 0.796 ng mL−1 in PBS and 2.203 ng mL−1 in human blood plasma with a turnaround time of 90 min. In comparison with conventional ELISA, highly sensitive and rapid HCV NS3 detection was accomplished colorimetrically on the developed μPISA platform.Article Citation - WoS: 17Citation - Scopus: 18Development of a Hydrocolloid Bio-Ink for 3d Bioprinting(Royal Society of Chemistry, 2022) Yıldırım, Özüm; Arslan Yıldız, AhuA new generation of bio-inks that are soft, viscous enough, stable in cell culture, and printable at low printing pressures is required in the current state of 3D bioprinting technology. Hydrogels can meet these features and can mimic the microenvironment of soft tissues easily. Hydrocolloids are a group of hydrogels which have a suitable gelling capacity and rheological properties. According to the literature, polysaccharide-based hydrocolloids are used in the food industry, wound healing technologies, and tissue engineering. Quince seed hydrocolloids (QSHs), which consist of mostly glucuronoxylan, can easily be obtained from quince seeds by water extraction. In this study, the use of a QSH as a bio-ink was investigated. The suitability of QSH for the printing process was assessed by rheological, uniformity and pore factor analyses. Appropriate printing parameters were determined and the characterization of the bioprinted QSHs was performed by SEM analysis, water uptake capacity measurement, and protein adsorption assay. The bioprinted QSHs had excellent water uptake capacity and showed suitable protein adsorption behaviour. Analyses of the biocompatibility and cellular viability of bioprinted QSHs were conducted using NIH-3T3 fibroblast cells and the results were found to be high during short and long-term cell culture periods. It was proved that QSH is a highly promising bio-ink for 3D bioprinting and further tissue engineering applications.Article Citation - Scopus: 6Sensitive and Rapid Protein Assay Via Magnetic Levitation(Elsevier, 2022) Sözmen, Alper Baran; Arslan Yıldız, AhuMagnetic levitation (MagLev) is a newly emerging methodology for biosensing that provides a density-based analysis, which is highly sensitive and versatile. In this study, a magnetic levitation based sensor platform was used for protein detection; and sensor platform optimization was performed for both sensitivity and resolution. Bovine Serum Albumin (BSA) was used as a model protein and detection of BSA was carried out by antibody functionalized polystyrene microspheres (PSMs). Various sizes of PSMs were examined and their performances were compared by statistical analyses in terms of limit of detection (LOD), sensitivity, and resolution. Quantification of the protein was done based on the magnetic levitation height differences of antibody functionalized PSMs. For optimization of the methodology, varied PSMs were utilized, and standardization of PSM diameter, concentration of the antibody to be functionalized, and PSM dilution rates were carried out. In conclusion, 20 μm PSMs diluted to 0.005% W/V and functionalized with anti-BSA antibody at a concentration of 28 μg/ml were determined to provide the best resolution for BSA detection. A dynamic range of 100 nM to 1 mM was observed with an LOD value of 4.1 ng/ml. This sensing platform promises a novel approach with a diverse application field and it provides rapid, consistent, and reproducible results with high resolution and sensitivity.Article Citation - WoS: 8Citation - Scopus: 11Cost-Effective and Rapid Prototyping of Pmma Microfluidic Device Via Polymer-Assisted Bonding(Springer, 2021) Sözmen, Alper Baran; Arslan Yıldız, AhuMicrofluidic systems are relatively new technology field with a constant need of novel and practical manufacturing materials and methods. One of the main shortcomings of current methods is the inability to provide rapid bonding, with high bonding strength, and sound microchannel integrity. Herein we propose a novel method of assembly that overcomes the mentioned limitations. Polymer-assisted bonding is a novel, rapid, simple, and inexpensive method where a polymer is solubilized in a solvent and the constituted solution is used as a bonding agent. In this study, we combined this method with utilization of several phase-changing materials (PCMs) as channel-protective agents. Glauber's salt appeared to be more suitable as a channel-protective agent compared to rest of the salts that have been used in this study. Based on the bonding strength, quality analyses, leakage tests, and SEM imaging, the superior assisting bonding solvent was determined to be dichloromethane with a PMMA concentration of 2.5% (W/V). It showed a bonding strength of 23.794 MPa and a nearly non-visible bonding layer formation of 2.83 mu m in width which is proved by SEM imaging. The said combination of PCM, solvent, and polymer concentration also showed success in leakage tests and an application of micro-droplet generator fabrication. The application was carried out to test the applicability of developed prototyping methodology, which resulted in conclusive outcomes as the droplet generator simulation run in COMSOL Multiphysics version 5.1 software. In conclusion, the developed fabrication method promises simple, rapid, and strong bonding with sharp and clear micro-channel engraving.Article Citation - WoS: 43Citation - Scopus: 46Glucuronoxylan-Based Quince Seed Hydrogel: a Promising Scaffold for Tissue Engineering Applications(Elsevier, 2021) Güzelgülgen, Meltem; Özkendir İnanç, Dilce; Yıldız, Ümit Hakan; Arslan Yıldız, AhuNatural gums and mucilages from plant-derived polysaccharides are potential candidates for a tissue-engineering scaffold by their ability of gelation and biocompatibility. Herein, we utilized Glucuron-oxylanbased quince seed hydrogel (QSH) as a scaffold for tissue engineering applications. Optimization of QSH gelation was conducted by varying QSH and crosslinker glutaraldehyde (GTA) concentrations. Structural characterization of QSH was done by Fourier Transform Infrared Spectroscopy (MR). Furthermore, morphological and mechanical investigation of QSH was performed by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The protein adsorption test revealed the suitability of QSH for cell attachment. Biocompatibility of QSH was confirmed by culturing NIH-3T3 mouse fibroblast cells on it. Cell viability and proliferation results revealed that optimum parameters for cell viability were 2 mg mi(-1)of QSH and 0.03 M GTA. SEM and DAPI staining results indicated the formation of spheroids with a diameter of approximately 300 pm. Furthermore, formation of extracellular matrix (ECM) microenvironment was confirmed with the Collagen Type-I staining. Here, it was demonstrated that the fabricated QSH is a promising scaffold for 3D cell culture and tissue engineering applications provided by its highly porous structure, remarkable swelling capacity and high biocompatibility. (C) 2021 Published by Elsevier B.V.Article Citation - WoS: 16Citation - Scopus: 13Fabrication of Tunable 3d Cellular Structures in High Volume Using Magnetic Levitation Guided Assembly(American Chemical Society, 2021) Onbas, Rabia; Arslan Yıldız, AhuTunable and reproducible size with high circularity is an important limitation to obtain three-dimensional (3D) cellular structures and spheroids in scaffold free tissue engineering approaches. Here, we present a facile methodology based on magnetic levitation (MagLev) to fabricate 3D cellular structures rapidly and easily in high-volume and low magnetic field. In this study, 3D cellular structures were fabricated using magnetic levitation directed assembly where cells are suspended and self-assembled by contactless magnetic manipulation in the presence of a paramagnetic agent. The effect of cell seeding density, culture time, and paramagnetic agent concentration on the formation of 3D cellular structures was evaluated for NIH/3T3 mouse fibroblast cells. In addition, magnetic levitation guided cellular assembly and 3D tumor spheroid formation was examined for five different cancer cell lines: MCF7 (human epithelial breast adenocarcinoma), MDA-MB-231 (human epithelial breast adenocarcinoma), SHSYSY (human bone-marrow neuroblastoma), PC-12 (rat adrenal gland pheochromocytoma), and HeLa (human epithelial cervix adenocarcinoma). Moreover, formation of a 3D coculture model was successfully observed by using MDA-MB-231 dsRED and MDA-MB-231 GFP cells. Taken together, these results indicate that the developed MagLev setup provides an easy and efficient way to fabricate 3D cellular structures and may be a feasible alternative to conventional methodologies for cellular/multicellular studies.
- «
- 1 (current)
- 2
- 3
- »