Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
37 results
Search Results
Now showing 1 - 10 of 37
Book Part Citation - Scopus: 1Molecular Dynamics Studies on Nanoscale Gas Transport(Springer Science+Business Media, 2015) Beşkök, Ali; Barışık, Murat[No abstract available]Article Citation - WoS: 7Citation - Scopus: 7Investigating the Effects of Pa66 Electrospun Nanofibers Layered Within an Adhesive Composite Joint Fabricated Under Autoclave Curing(American Chemical Society, 2023) Esenoğlu, Gözde; Tanoğlu, Metin; Barışık, Murat; İplikçi, Hande; Yeke, Melisa; Nuhoğlu, Kaan; Türkdoğan, Ceren; Martin, Seçkin; Aktaş, Engin; Dehneliler, Serkan; Gürbüz, Ahmet Ayberk; İriş, Mehmet ErdemEnhancing the performance of adhesively joined composite components is crucial for various industrial applications. In this study, polyamide 66 (PA66) nanofibers produced by electrospinning were coated on unidirectional carbon/epoxy prepregs to increase the bond strength of the composites. Carbon/epoxy prepregs with/without PA66 nanofiber coating on the bonding region were fabricated using the autoclave, which is often used in the aerospace industry. The single lap shear Charpy impact energy and Mode-I fracture toughness tests were employed to examine the effects of PA66 nanofibers on the mechanical properties of the joint region. Scanning electron microscopy (SEM) was used to investigate the nanofiber morphology and fracture modes. The thermal characteristics of Polyamide 66 nanofibers were explored by using differential scanning calorimetry (DSC). We observed that the electrospun PA66 nanofiber coating on the prepreg surfaces substantially improves the joint strength. Results revealed that the single lap shear and Charpy impact strength values of the composite joint are increased by about 79 and 24%, respectively, by coating PA66 nanofibers onto the joining region. The results also showed that by coating PA66 nanofibers, the Mode-I fracture toughness value was improved by about 107% while the glass transition temperature remained constant.Article Citation - WoS: 9Citation - Scopus: 13Analysis of Adhesively Bonded Joints of Laser Surface Treated Composite Primary Components of Aircraft Structures(Elsevier, 2023) Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Tanoğlu, Metin; İplikçi, Hande; Barışık, Murat; Yeke, Melisa; Türkdoğan, Ceren; Esenoğlu, Gözde; Dehneliler, SerkanThe performance of the adhesively bonded aerospace structures highly depends on the adhesion strength between the adhesive and adherents, which is affected by, in particular, the condition of the bonding surface. Among the various surface treatment methods, as state of the art, laser surface treatment is a suitable option for the CFRP composite structures to enhance the adhesion performance, adjusting the roughness and surface free energy with relatively minimizing the damage to the fibers. The aim of this study is the validation and evaluation of the adhesive bonding behavior of the laser surface-treated CFRP composite structures, using the finite element technique to perform a conservative prediction of the failure load and damage growth. Such objectives were achieved by executing both experimental and numerical analyses of the secondary bonded CFRP parts using a structural adhesive. In this regard, to complement physical experiments by means of numerical simulation, macro-scale 3D FEA of adhesively bonded Single Lap Joint and Skin-Spar Joint specimens has been developed employing the Cohesive Zone Model (CZM) technique in order to simulate bonding behavior in composite structures especially skin-spar relation in the aircraft wing-box.Article Citation - WoS: 15Citation - Scopus: 17Effects of Nanosecond Laser Ablation Parameters on Surface Modification of Carbon Fiber Reinforced Polymer Composites(SAGE Publications, 2023) Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Türkdoğan, Ceren; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemRemoval of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/?45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.Article Citation - WoS: 8Citation - Scopus: 8Improving Adhesive Behavior of Fiber Reinforced Composites by Incorporating Electrospun Polyamide-6,6 Nanofibers in Joining Region(SAGE Publications, 2022) Esenoğlu, Gözde; Barışık, Murat; Tanoğlu, Metin; Yeke, Melisa; Türkdoğan, Ceren; İplikçi, Hande; Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemAdhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 +/- 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially.Article Citation - WoS: 5Citation - Scopus: 6Active Heat Transfer Enhancement by Interface-Localized Liquid Dielectrophoresis Using Interdigitated Electrodes(Elsevier, 2022) Yenigün, Onur; Barışık, MuratWe introduced an active heat transfer control between graphene and water using interdigitated electrodes (IDEs). Oppositely charged co-planer electrodes embedded on a graphene surface created a non-uniform electric field. Resulted interface localized liquid dielectrophoresis (LDEP) perpendicular to surface enhanced the water/graphene coupling and decreased interfacial thermal resistance (ITR) substantially. We correlated the theoretical calculations of average electric field strength near surface with Kapitza values measured at corresponding electrode configurations. We obtained a unified linear variation of Kapitza as a function of average electric strength independent of electrode size and charge. By increasing the electric field strength, we measured up to 96% decrease of Kapitza near electrodes. Since the IDEs generated electric field was only interface localized, it required lower electrode charges than any parallel-plate capacitor systems. We showed that ITR remains effective in heat transfer behavior for systems as big as 100nm such that interface localized electric field can at least increase the heat removal 50% by eliminating the ITR from both graphene/water interfaces of a channel system. By converting hydrophobic few-layer graphene to super-hydrophilic condition with ultra-low Kapitza, current results are important for graphene-based materials considered for the solution of the thermal management problem of current and next generation micro/nano-electronics.Article Citation - WoS: 16Citation - Scopus: 17Thermal and Hydrodynamic Behavior of Forced Convection Gaseous Slip Flow in a Kelvin Cell Metal Foam(Elsevier, 2022) Sabet, Safa; Barışık, Murat; Buonomo, Bernardo; Manca, OronzioPorous metallic foams are a key material in numerous thermal and hydraulic applications. Gas flows in such micro/nanoporous systems deviate from classical continuum descriptions due to nonequilibrium in gas dynamics, and the resulted heat and mass transport show variation by rarefaction. This study performed a wide range of pore-level analysis of convective gas flows in a Kelvin cell model at different porosities and working conditions. Rarefaction effects onto permeability and heat transfer coefficients were calculated through Darcy to Forchheimer flow regimes. Permeability increased up to 60% by increasing rarefaction while this enhancement decreased by increasing porosity. At the same time, rarefaction lessened inertial effects such that Forchheimer coefficients decreased substantially. At high flow velocities, the increase in rarefaction considerably decreased the effect of drag forces. Hence, hydrodynamic enhancement due to rarefaction was found to increase by increasing Reynolds number. On the other hand, positive influence of boundary slip and negative influence of temperature jump developing between gas and solid almost canceled each other for the studied low heat flux region of highly conductive metal foam structures. Hence, Nusselt numbers were found mostly related to Reynolds number independent from rarefaction. We described Nusselt value based on power law model as a function of Reynolds and porosity. Results and the proposed model are important to accurately predict the thermal and hydrodynamic performance of metal foams in the 80 PPI range.Article Citation - WoS: 7Citation - Scopus: 8Size and Roughness Dependent Temperature Effects on Surface Charge of Silica Nanoparticles(Elsevier, 2021) Alan, Büşra Öykü; Barışık, MuratSilica nanoparticles (SNP) with different sizes and surface areas are used in numerous micro/nanofluidic applications, while their surface charge properties play a major role in their function. In many of these applications, SNPs also undergo temperature variation. We present that an increase in temperature yields a substantial increase in SNP surface charge depending on nanoparticle size and surface roughness, which cannot be estimated by existing theory. As a continuation of our earlier work characterizing the deviation of SNP surface charging from theoretical predictions due to curvature and EDL overlap effects, this study presents the differentiation from the theory in temperature dependence under various conditions. As we calculate surface chemistry as a function of local ionic conditions (Charge Regulation), temperature variation changed the equilibrium constants of protonation/deprotonation reactions of the SNP surface, in addition to changes occurring in relative permittivity and ionic mobilities. Results show that variation of SNP surface charge by temperature decreases by decreasing particle size and/or increasing roughness size, compare to theoretical flat plate calculations considering similar temperature-dependent properties and charge regulation on the surface. We characterized these deviations by obtaining an electrokinetic similarity between different systems of various size and roughness at various ionic conditions based on the non-dimensional groups of lambda/DP and lambda/DR. Based on these, we devised a phenomenological model as an extension to the flat plate theory to successfully predict the surface charge of SNPs as a function of the particle size, roughness size, and temperature. The current findings are important for the characterization of SNPs through temperature variations and can also be used to adjust the surface charge of SNPs by tuning the temperature.Article Citation - WoS: 16Citation - Scopus: 16Slip Effects on Ionic Current of Viscoelectric Electroviscous Flows Through Different Length Nanofluidic Channels(American Chemical Society, 2020) Şen, Tümcan; Barışık, MuratThe pressure driven slip flow of an electrolyte solution is studied through different nanofluidic channel lengths at varying salt concentrations. The viscous-thickening due to the electrostatic interactions within the electric double layer and the reverse ionic transport due to the streaming potential are developed. The influence of the Navier slip boundary condition is described under both electroviscous and viscoelectric effects with a surface charge regulation (CR) model while the observed behavior is compared and validated with molecular dynamic (MD) calculations from multiple studies. Results show that electroviscous and viscoelectric effects decrease transport. Earlier studies at the no slip boundary presented an increase of ionic current by increasing salt concentration and decreasing channel length. In contrast, our study found that the ionic current occurred almost independent of both salt concentration and channel length, except for very short channels and very low salt concentrations, when electroviscous and viscoelectric effects were considered. In the case of the constant slip length condition, ionic conduction was enhanced, but velocity slip developing on surfaces showed significant variation based on the salt concentration and channel length. This is due to the natural CR behavior enhancing the surface charge and consequential near surface electrohydrodynamics as a result of increase in salt concentration and/or decrease of channel length. Considering that the electroviscous effect alone creates up to 70% lower velocity slips than Poiseuille flow predictions, while further including the viscoelectric effect, results in an almost no-slip condition at high salt concentrations and/or short channels. As a result, the ionic current of a viscoelectric electroviscous slip flow is found to be equal to 1/3 of an electroviscous slip flow and to decrease with a decrease in the channel length.Article Citation - WoS: 32Citation - Scopus: 34Pore Size and Porosity Dependent Zeta Potentials of Mesoporous Silica Nanoparticles(American Chemical Society, 2020) Yakın, Fetiye Esin; Barışık, Murat; Şen, TümcanMesoporous silica nanoparticles (MSNPs) are synthesized in the various forms of porous structures according to an application's needs, while their zeta potentials play a major role in their function. We show that variation in pore size and/or porosity yields a substantial decrease in MSNP zeta potential up to 25% lower than the theoretical zeta potential predictions for a flat surface at the corresponding ionic conditions in moderate pH range. By considering surface chemistry as a function of local ionic conditions (charge regulation), we calculated local zeta potentials around the MSNP which showed variation between pore openings and solid surfaces. Through a systematic study, we evaluated an average three-dimensional zeta potential for MSNPs with various conditions, based on the ratio of the area covered by pore openings to the rest of the MSNP surface area as a function of three-dimensional porosity and pore size. Results show that the high overlap of ionic layers inside the pores creates electric potentials close to zeta potential of the remaining surface, but large pore size and/or high ionic salt concentration yields divergence. We characterized the variation of MSNP zeta potential in terms of porosity (epsilon(3D)), pore size (D-pore), and ionic condition quantified by Debye length (lambda) and obtained unified behavior as a function of the nondimensional group of epsilon(3D)(D-pore/lambda). For epsilon(3D)(D-pore/lambda) < 0.01, MSNP zeta potential remains similar to flat plate predictions, but it decreases by increasing epsilon(3D)(D-pore/lambda) value. The influence of pore entrances on surface zeta potential increases nonlinearly by the increase of porosity and/or decrease of EDL overlap, similar to a change of area to volume ratio. The current findings are important for the understanding and further control of mesoporous particle transport in various promising and groundbreaking applications such as targeted drug delivery.