Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
4 results
Search Results
Now showing 1 - 4 of 4
Article Citation - WoS: 5Citation - Scopus: 4Influence of Partitioning Treatment on Microstructure and Mechanical Properties of an Alloyed Ductile Iron Austempered at Different Temperatures(Walter de Gruyter GmbH, 2023) Neite, Maximilian; Münstermann, Sebastian; Nalçacı, Burak; Davut, Kemal; Erdoğan, MehmetThe present study was conducted to uncover effects of partitioning treatment on Cu-Ni-Mo alloyed ductile iron (DI) austempered at different temperatures. For this purpose, the DI samples, produced via sand casting, were austenitized at 900 °C for 60 min, followed by austempering at the temperatures of 275-325-375 °C for 120 min and afterwards a partitioning treatment was applied at 200 °C for 15 min. In the characterization studies, dilatometer, image analysis, JMat-Pro, mechanical tests, XRD, optical microscope, and scanning electron microscope (SEM) equipped with EBSD detector were utilized. Characterization studies showed that the effects of partitioning treatment were directly correlated with austempering temperature and high carbon austenite volume fraction changed in the range of 19.48-35.45%. That redistribution of carbon (C) between bainitic ferrite and high carbon austenite occurred, in turn, the carbon content of high carbon austenite increased with the partitioning treatment irrespective of austempering temperature were uncovered. Furthermore, the partitioning treatment considerably changed the grain morphologies of both high carbon austenite and banitic ferrite. As a consequence of these microstructural differences, the highest tensile strength of 1489.2 MPa was established in the sample austempered at 275 °C and partitioned at 200 °C, whereas the highest ductility of 5.61% acquired at the austempering temperature of 375 °C. © 2023 Walter de Gruyter GmbH, Berlin/Boston.Article Citation - WoS: 29Citation - Scopus: 31Effect of Heat Input on Haz Softening in Fiber Laser Welding of 22mnb5 Steel(Elsevier, 2023) Tuncel, Oğuz; Aydın, Hakan; Davut, KemalThis study investigates the effects of heat input on the heat-affected zone (HAZ) softening in fiber laser welding of quenched 1.1 mm thick 22MnB5 steel. Laser power (1500-2500 W) and welding speed (40-120 mm/s) parameters are considered as the input process variables. Depending on the input parameters, the applied heat input varied between 12.5 and 62.5 J/mm. The results indicate that a minimum heat input of 50 J/mm is required for full weld penetration. Microhardness findings revealed that the drop in hardness in the HAZ region relative to the base material (BM) reached 39% due to grain coarsening caused by an increase in heat input under the welding conditions. Grain coarsening (prior austenite grains) is also detected in SEM analysis. In addition, grain coarsening at high heat input was also determined quantitatively in EBSD analyses. The proportion of 8.91 mu m grain size in the sample with high heat input is 4.2%, while it is 1.2% in the sample with low heat input. When the heat input increased from 12.5 to 62.5 J/mm, the width of the softened zone with the lowest hardnesses in the HAZ grew from 0.2 mm to 2.2 mm.Article Citation - WoS: 5Citation - Scopus: 6Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel(Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.Article Citation - WoS: 39Citation - Scopus: 41Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier, 2022) Özer, Seren; Bilgin, Güney Mert; Davut, Kemal; Esen, Ziya; Dericioğlu, Arcan.FThe effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples disappeared and converted into a mixture of columnar and equiaxed grains. Nano-sized γ″ and/or γ′ precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 °C for 8 h) tested at 600 °C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700–800 °C, which was attributed to intermediate temperature embrittlement.