Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
104 results
Search Results
Now showing 1 - 10 of 104
Article Citation - WoS: 5Citation - Scopus: 5Investigation and Validation of the Flow Stress Equation and Damage Model Parameters of an Electron Beam Melted Ti6al4v Alloy With a Martensitic Phase(Elsevier, 2023) Güden, Mustafa; Bin Riaz, Arslan; Toksoy, Ahmet Kaan; Yıldıztekin, Murat; Erten, Hacer İrem; Çimen, Gülden; Hızlı, BurakThe Johnson and Cook flow stress and damage model parameters of an electron beam melt (EBM)-Ti64 alloy composed of & alpha;' (martensite) and & alpha;+& beta; and an extruded-annealed conventional Ti64 alloy were determined experimentally. The validities of the determined flow stress equations and damage model parameters were then verified by the numerical simulations of the compression tests on the Body Centered Cubic lattices produced using the same EBM parameters with the solid EBM samples. In addition, a compression flow stress equation was extracted from the small-size test specimens (1 and 2 mm diameter) taken directly from the struts of the as-built lattices. The microscopic observations, XRD analyses and hardness tests confirmed the presence of & alpha;& PRIME; phase in the EBM solid samples and in the struts of the BCC lattices, which reduced the ductility of the EBM solid specimens and struts compared to the conventional Ti64. Furthermore, the partially melt particles on the surfaces of the struts acted as the stress concentration sides for micro-cracking; hence, the compression flow stresses of the struts were found to be significantly lower than those of the as-built EBM solid specimens. The flow stress equation derived from the struts predicted more accurately the compression behavior of the lattices. The compression tests and models showed that early damage formation in the lattices was noted to decrease the initial peak and post peak stresses. As with the experiments, the initial damage occurred in the models with the separation of the nodes at the lattice cell surface edges. This resulted in an abrupt reduction in the stresses after the peak stress. The numerical lattices without damage showed a localized lattice deformation at the mid-sections and the stress increased continuously as a function of normal strain.Article Citation - WoS: 12Citation - Scopus: 12High Strain-Rate Deformation Analysis of Open-Cell Aluminium Foam(Elsevier, 2023) Mauko, Anja; Duarte, Isabel; Borovinšek, Matej; Vesenjak, Matej; Ren, Zoran; Sarıkaya, Mustafa; Güden, MustafaThis study investigated the high-strain rate mechanical properties of open-cell aluminium foam M-pore®. While previous research has examined the response of this type of foam under quasi-static and transitional dynamic loading conditions, there is a lack of knowledge about its behaviour under higher strain rates (transitional and shock loading regimes). To address this gap in understanding, cylindrical open-cell foam specimens were tested using a modified Direct Impact Hopkinson Bar (DIHB) apparatus over a wide range of strain rates, up to 93 m/s. The results showed a strong dependency of the foam's behaviour on the loading rate, with increased plateau stress and changes in deformation front formation and propagation at higher strain rates. The internal structure of the specimens was examined using X-ray micro-computed tomography (mCT). The mCT images were used to build simplified 3D numerical models of analysed aluminium foam specimens that were used in computational simulations of their behaviour under all experimentally tested loading regimes using LS-DYNA software. The overall agreement between the experimental and computational results was good enough to validate the built numerical models capable of correctly simulating the mechanical response of analysed aluminium foam at different loading rates. © 2023 The AuthorsArticle Citation - WoS: 1Citation - Scopus: 1Epoxy Matrix Nano Composites: Modulus, Strength and Ductility Enhancement Through Auxeticity of Α-Cristobalite Filler(Elsevier, 2023) Güden, Mustafa; Ülker, Sevkan; Movahedi, NimaThe negative Poisson's ratio (NPR) nano-size ?-Cristobalite particle/epoxy composites were prepared and tensile tested. The elastic modulus and strength of the composites were improved as the particle volume fraction increased from 0 to 0.02. Unlike the conventional particle reinforced composites, the fracture strain increased with the nano ?-Cristobalite addition, an effect which was ascribed to the intrinsic NPR behavior of the filler. © 2023 Elsevier B.V.Article Citation - WoS: 18Citation - Scopus: 19The Impact Response of a Nomex® Honeycomb Core/E-glass Composite Sandwich Structure To Increasing Velocities: Experimental and Numerical Analysis(Elsevier, 2023) Çelik, Muhammet; Güden, Mustafa; Sarıkaya, Mustafa; Taşdemirci, Alper; Genç, Cem; Ersoy, Kurtuluş; Serin, ÖzgürThe impact response of an E-glass fiber reinforced epoxy/Nomex® honeycomb core sandwich was investigated both experimentally and numerically at increasing velocities through concentrated quasi-static indentation force (CQIF), low velocity impact (LVI) and high velocity impact (HVI) tests. The composite face sheets and core were modelled using MAT_162 and MAT_026 homogenized material model in LS-DYNA, respectively. The experimental and numerical LVI test forces corresponding to core crushing and face sheet penetration were shown to be higher than those of the CQIF tests and increased as the impactor velocity increased. The increase of the impact forces at increasing velocities was largely ascribed to the inertia and the strain rate sensitive fracture strength of the composite sheets. The core shearing was detected in the CQIF and LVI tests both experimentally and numerically. It was also detected in the HVI tests at the velocities less than 20 m s?1. The deformation in the HVI tests at and above ? 29.4 m s?1 was highly localized in the impact area with no core shearing and a large delamination damage area at the front face sheet. The force enhancement due to the micro-inertia of the core deformation was shown to be not significant at the studied velocities. © 2023 Elsevier LtdArticle Citation - WoS: 12Citation - Scopus: 17Development of the Johnson-Cook Flow Stress and Damage Parameters for the Impact Response of Polycarbonate: Experimental and Numerical Approach(Elsevier, 2023) Sarıkaya, Mustafa; Güden, Mustafa; Kambur, Çağdaş; Çankaya Özbek, Sevim; Taşdemirci, AlperThe Johnson and Cook (JC) flow stress and damage model parameters of a polycarbonate (PC) plate were determined by the mechanical tests and numerical simulations of the tests. The experimental tests included quasi-static and high strain rate tension and compression, quasi-static notched-specimen tension, quasi-static indentation (QSI), low velocity impact (LVI) and projectile impact (PI). Initially, five different quasi-static flow stress-strain equations were extracted from the experimental and numerical tests. The flow stress equa-tion determined from the experimental average true stress-true strain curve well agreed with the effective stress -strain obtained from the quasi-static numerical tension test. The numerical QSI force-displacement curve based on the experimental average true stress-true strain equation was further shown to be very similar to that of the experiment. The LVI and PI test simulations were then continued with the experimental average true stress-true strain equation using five different flow stress-strain rate relations: JC, Huh and Kang (HK), Allen-Rule and Jones (ARJ), Cowper-Symonds (CS) and the nonlinear rate approach (NLA). The rate sensitivity parameters of these relations were extracted from the quasi-static and high strain rate tests. The LVI test simulations using the stress -strain rate relations exhibited force-displacement curves higher than those of the experiments. The detected almost no strain rate sensitivity in the LVI tests was ascribed to low strain rate dependency of the flow stress at these intermediate strain rates and large strains involved. On the other side, all the stress-strain rate relations investigated nearly predicted the experimental damage types: dishing at 100 and 140 m s-1 and petalling at 160 m s- 1, except the CS relation which predicted the fracture of the plate at 140 m s-1. The experimental average projectile exit velocity at 160 m s- 1 was further well predicted by the used stress-strain rate relations while the experimental average petal thicknesses were under estimated by the models. The absorbed energy at 160 m s-1 PI test was determined 1.6 times that of the QSI test, which proved an increased energy absorption capability of the tested PC at the investigated impact velocities.Article Citation - WoS: 15Citation - Scopus: 15The Effect of Strain Rate on the Compression Behavior of Additively Manufactured Short Carbon Fiber-Reinforced Polyamide Composites With Different Layer Heights, Infill Patterns, and Built Angles(Springer, 2023) Zeybek, Mehmet Kaan; Güden, Mustafa; Taşdemirci, AlperPrevious studies on the fused deposition modelling (FDM) processed short carbon fiber/Polyamide 6 (PA6) matrix composites and neat PA6 have mostly concentrated on the quasi-static mechanical properties. Present study focused on the strain rate-dependent deformation behavior of a short carbon fiber-reinforced PA6 (Onyx) and neat PA6, produced in different layer heights, infill patterns and built angles. As compared with PA6, Onyx showed a higher compression stress at all strain rates investigated. A layer height of 0.2 mm in PA6 specimens promoted a better bonding between [0/90°] infill layers; hence, a higher flow stress than 0.2 mm layer height specimens, while 0.2 mm layer height induced a higher porosity in Onyx specimens, leading to a lower flow stress. The porosities in Onyx [0/90°] infill specimens were due to the constraining effect of 0/90° fiber layers. Changing infill pattern from a [0/90°] to a concentric one decreased porosity at the same layer height and hence increased the compressive flow stress. The highest compressive strength was found in the specimens with the loading axis 90 and 0° to [0/90°] infill plane. The lowest strength was, however, determined in the specimens with the loading axis 30 and 60o to [0/90°] infill plane in quasi-static loading. However, the specimens with the loading axis of 60, 45, 30 and 0° exhibited a brittle behavior in high strain rate loading (1500 s−1). The specimens with the loading axis of 45° had the lowest fracture stress and strain in the high strain rate loading. This signified the importance of loading angle at high strain rates. Finally, the rate sensitivities of PA6 and Onyx specimens were shown to be similar, showing a matrix dominated deformation. However, the strain rate jump tests indicated a slightly higher rate sensitivity of Onyx specimens at quasi-static strain rates (10−3-10−1 s−1).Article Citation - WoS: 3Citation - Scopus: 3Quasi-Static and Dynamic Brazilian Testing and Failure Analysis of a Deer Antler in the Transverse To the Osteon Growth Direction(Elsevier, 2023) Orhan, Mehmet; Sarıkaya, Mustafa Kemal; Taşdemirci, Alper; Tuncer, Can; Güden, MustafaThe transverse tensile strength of a naturally fallen red deer antler (Cervus Elaphus) was determined through indirect Brazilian tests using dry disc-shape specimens at quasi-static and high strain rates. Dynamic Brazilian tests were performed in a compression Split-Hopkinson Pressure Bar. Quasi-static tensile and indirect Brazilian tests were also performed along the osteon growth direction for comparison. The quasi-static transverse tensile strength ranged 31.5–44.5 MPa. The strength increased to 83 MPa on the average in the dynamic Brazilian tests, proving a rate sensitive transverse strength. The quasi-static tensile strength in the osteon growth direction was however found comparably higher, 192 MPa. A Weibull analysis indicated a higher tensile ductility in the osteon growth direction than in the transverse to the osteon growth direction. The microscopic analysis of the quasi-static Brazilian test specimens (tensile strain along the osteon growth direction) revealed a micro-cracking mechanism operating by the crack deflection/twisting at the lacunae in the concentric lamellae region and at the interface between concentric lamellae and interstitial lamellae. On the other side, the specimens in the transverse direction fractured in a more brittle manner by the separation/delamination of the concentric lamellae and pulling of the interstitial lamellae. The detected increase in the transverse strength in the high strain rate tests was further ascribed to the pull and fracture of the visco-plastic collagen fibers in the interstitial lamellae. This was also confirmed microscopically; the dynamically tested specimens exhibited flatter fracture surfaces. © 2023 Elsevier LtdArticle Citation - WoS: 9Citation - Scopus: 9The Strain Rate History Effect in a Selective-Laser 316l Stainless Steel(Elsevier, 2023) Enser, Samed; Güden, Mustafa; Taşdemirci, Alper; Davut, KemalThe strain rate history effect in a selective laser melt 316L (SLM-316L) alloy was investigated through quasi-static (10−3 s−1) and high strain rate (1600-3200 s−1) interrupted and reloading compression tests. The specimens pre-tested until about prescribed strains at quasi-static and high strain rates were reloaded dynamically and quasi-statically, respectively. The results revealed that the flow stress depended on strain and strain rate as well as strain-rate history. Quasi-static reloading the dynamically pre-tested specimens until about prescribed strains induced a higher flow stress than the specimens tested quasi-statically. The strengthening was ∼70 MPa at 0.11 pre-strain and decreased as the dynamic test pre-strain was increased due to adiabatic heating. On the other side, reloading the quasi-statically pre-tested specimens dynamically at 0.11 pre-strain resulted in ∼60 MPa lower flow stress than the specimens tested dynamically. The grains of the quasi-statically tested specimens until 0.11 strain were shown to have a lower Taylor factor for twinning and geometrically necessary dislocation density, indicating more potential for twinning than dynamically tested specimen. Although, quasi-statically and dynamically tested specimens were deformed predominantly by the twinning induced plasticity, a higher fraction of twin boundaries was shown microscopically in the dynamically pre-tested specimens until 0.11 pre-strain. This phenomenon of boundary strengthening could be used as a tool of strengthening of SLM-316L alloy at low strains.Article Citation - WoS: 1Citation - Scopus: 1Investigation of Penetration Behavior of Combined Geometry Shells at Quasi-Static and Intermediate Strain Rates: an Experimental and Numerical Study(Elsevier, 2023) Turan, Ali Kıvanç; Taşdemirci, Alper; Kara, Ali; Şahin, Selim; Güden, MustafaIn this study, the penetration/perforation behavior of a core material with previously determined static and dynamic crushing characteristics was investigated both experimentally and numerically. Penetration/perforation problems occur due to shrapnel effect when sandwich structures containing energy-absorbing core materials by crushing are exposed to blast loads. The penetration behavior of combined geometry shells consisting of a hemispherical cap and a cylindrical segment was investigated experimentally using blunt, conical and hemispherical penetrator tips. The quasi-static penetration tests were performed in a universal test machine, and the intermediate strain rate penetration tests were performed in a drop weight test device. The numerical models of penetration tests were implemented in LS-DYNA at the test strain rates as well as at the higher strain rates. Results showed that different penetrator geometries induced damage forms of symmetrical tearing, petaling, plugging and inversely formed hemispherical domed cone. The increase in the thickness of core geometry resulted in a decent increase in force–displacement curves, as average of force levels increased around 140%, 200% and 220% for blunt, conical and hemispherical tip penetrators, respectively. Numerical results indicated very good correlation with experimental work and enabled to investigate effect of strain rate and micro-inertia over numerical models at elevated penetrator velocities. Penetration behavior was found to be affected from micro-inertia effects up to a threshold displacement of 4 mm for thicker and 5 mm for thinner core units and strain rate effects were found to be dominant beyond that point.Conference Object Asymmetry in the Tension and Compression Flow Stress and the Effect of Sub-Cell Size on the Hardness of a Selective Laser Melt 316l Stainless Steel(Springer, 2022) Güden, Mustafa; Enser, Samed; Arslan Hamat, Burcu; Tanrıkulu, A. Alptuğ; Yavaş, HakanAn asymmetry between tension and compression tests was determined experimentally in the Selective Laser Melt (SLM) stainless steel 316L alloy in the building direction. The asymmetry was ascribed to the used biaxial scanning strategy which resulted in a strong alignment of 〈110〉 along the build direction (fiber texture) and a random distribution of 〈100〉, 〈110〉 and 〈111〉 directions normal to the building direction. The strong fiber texture in the building direction induced lower twinning stress in tension than in compression, while the tension and compression twining stresses were found similar in the normal to building direction. The favored twinning in the specimens tested in the building direction resulted in a higher tensile true fracture strain; hence, a higher ductility. Lastly, the hardness measurements made on the specimens having similar gain sizes, but different sub-cell sizes processed using higher and lower laser powers tended to support that the sub-cell boundaries in SLM-316L alloy acted as imperfect barriers to the dislocation motion.