Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

2008 - 20093

Settings

Author: search.filters.author.Seyhan, Abdullah TuğrulSubject: search.filters.subject.Fracture toughness

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 73
    Citation - Scopus: 92
    Tensile Mechanical Behavior and Fracture Toughness of Mwcnt and Dwcnt Modified Vinyl-ester/Polyester Hybrid Nanocomposites Produced by 3-Roll Milling
    (Elsevier Ltd., 2009) Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, Karl
    This study aims to investigate the tensile mechanical behavior and fracture toughness of vinyl-ester/polyester hybrid nanocomposites containing various types of nanofillers, including multi- and double-walled carbon nanotubes with and without amine functional groups (MWCNTs, DWCNTs, MWCNT-NH2 and DWCNT-NH2). To prepare the resin suspensions, very low contents (0.05, 0.1 and 0.3 wt.%) of carbon nanotubes (CNTs) were dispersed within a specially synthesized styrene-free polyester resin, conducting 3-roll milling technique. The collected resin stuff was subsequently blended with vinyl-ester via mechanical stirring to achieve final suspensions prior to polymerization. Nanocomposites containing MWCNTs and MWCNT-NH2 were found to exhibit higher tensile strength and modulus as well as larger fracture toughness and fracture energy compared to neat hybrid polymer. However, incorporation of similar contents of DWCNTs and DWCNT-NH2 into the hybrid resin did not reflect the same improvement in the corresponding mechanical properties. Furthermore, experimentally measured elastic moduli of the nanocomposites containing DWCNTs, DWCNT-NH2, MWCNTs and MWCNT-NH2 were fitted to Halphin-Tsai model. Regardless of amine functional groups or content of carbon nanotubes, MWCNT modified nanocomposites exhibited better agreement between the predicted and the measured elastic moduli values compared to nanocomposites with DWCNTs. Furthermore, Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM) were used to reveal dispersion state of the carbon nanotubes within the hybrid polymer and to examine the CNT induced failure modes that occurred under mechanical loading, respectively. Based on the experimental findings obtained, it was emphasized that the types of CNTs and presence of amine functional groups on the surface of CNTs affects substantially the chemical interactions at the interface, thus tuning the ultimate mechanical performance of the resulting nanocomposites.
  • Article
    Citation - WoS: 24
    Citation - Scopus: 26
    Cure Kinetics of Vapor Grown Carbon Nanofiber (vgcnf) Modified Epoxy Resin Suspensions and Fracture Toughness of Their Resulting Nanocomposites
    (Elsevier Ltd., 2009) Seyhan, Abdullah Tuğrul; Sun, Z.; Deitzel, J.; Tanoğlu, Metin; Heider, D.
    In this study, the cure kinetics of Cycom 977-20, an aerospace grade toughened epoxy resin, and its suspensions containing various amounts (1, 3 and 5 wt.%) of vapor grown carbon nanofibers (VGCNFs) with and without chemical treatment were monitored via dynamic and isothermal dynamic scanning calorimetry (DSC) measurements. For this purpose, VGCNFs were first oxidized in nitric acid and then functionalized with 3-glycidoxypropyltrimethoxy silane (GPTMS) coupling agent. Fourier transform infrared (FTIR) spectroscopy was subsequently used to verify the chemical functional groups grafted onto the surfaces of VGCNFs. Sonication technique was conducted to facilitate proper dispersion of as-received, acid treated and silanized VGCNFs within epoxy resin. Dynamic DSC measurements showed that silanized VGCNF modified resin suspensions exhibited higher heat of cure compared to those with as-received VGCNFs. Experimentally obtained isothermal DSC data was then correlated with Kamal phenomenological model. Based on the model predictions, it was found that silanized VGCNFs maximized the cure reaction rates at the very initial stage of the reaction. Accordingly, an optimized curing cycle was applied to harden resin suspensions. Fracture testing was then carried out on the cured samples in order to relate the curing behavior of VGCNF modified resin suspensions to mechanical response of their resulting nanocomposites. With addition of 1 wt.% of silanized VGCNFs, the fracture toughness value of neat epoxy was found to be improved by 12%. SEM was further employed to examine the fracture surfaces of the samples.
  • Article
    Citation - WoS: 182
    Citation - Scopus: 214
    Mode I and Mode Ii Fracture Toughness of E-Glass Non-Crimp Fabric/Carbon Nanotube (cnt) Modified Polymer Based Composites
    (Elsevier Ltd., 2008) Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, Karl
    In this study, mode I and mode II interlaminar fracture toughness, and interlaminar shear strength of E-glass non-crimp fabric/carbon nanotube modified polymer matrix composites were investigated. The matrix resin containing 0.1 wt.% of amino functionalized multi walled carbon nanotubes were prepared, utilizing the 3-roll milling technique. Composite laminates were manufactured via vacuum assisted resin transfer molding process. Carbon nanotube modified laminates were found to exhibit 8% and 11% higher mode II interlaminar fracture toughness and interlaminar shear strength values, respectively, as compared to the base laminates. However, no significant improvement was observed for mode I interlaminar fracture toughness values. Furthermore, Optical microscopy and scanning electron microscopy were utilized to monitor the distribution of carbon nanotubes within the composite microstructure and to examine the fracture surfaces of the failed specimens, respectively. © 2008 Elsevier Ltd. All rights reserved.