Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
176 results
Search Results
Now showing 1 - 10 of 176
Article Citation - WoS: 4Citation - Scopus: 4Adsorption Kinetics of Methane Reformer Off-Gases on Aluminum Based Metal-Organic Framework(Elsevier Ltd., 2020) Angı, Deniz; Çakıcıoğlu Özkan, Seher FehimeSolvothermal synthesis of aluminum based metal-organic frameworks (MIL-53(Al)s) were conducted by considering the effects of crystallization and activation temperatures, and the solvent at purification step. Adsorption kinetics of Steam Methane Reformer off gas components at 34, 70 and 100 °C temperatures was measured by using ZLC method. Henry constant decreases as diffusion coefficient of the gases increases with increasing temperature; It was determined that the CO gas has the highest activation energy. Adsorption kinetics of gases were controlled with electrostatic interaction. © 2020 Hydrogen Energy Publications LLCArticle Citation - WoS: 8Citation - Scopus: 9Polymeric Thermal Analysis of C+h and C+h+ar Ion Implanted Uhmwpe Samples(Elsevier Ltd., 2007) Kaya, N.; Öztarhan, Ahmet M.; Urkaç, Emel Sokullu; Ila, D.; Budak, S.; Oks, E.; Tıhmınlıoğlu, Funda; Muntele, C.Chemical surface characterization of C + H hybrid ion implanted UHMWPE samples were carried out using DSC (differential scanning calorimeter) and TGA (thermal gravimetric analysis) techniques. Samples were implanted with a fluence of 10(17) ion/cm(2) and an extraction voltage of 30 kV. The study of TGA and DSC curves showed that: (1) Polymeric decomposition temperature increased, (2) T-m, Delta C-p and Delta H-m values changed while Delta C-p and Delta H-m increased. T-g value could not be measured, because of some experimental limitations. However, the increase in Delta H-m values showed that T-g values increased, (3) the branch density which indicated the increase in number of cross-link (M-c) decreased in ion implanted samples and (4) increase in Delta H-m values indicated increase in crystallinity of implanted surface of UHMWPE samples.Article Citation - WoS: 54Citation - Scopus: 64Bioactive Fish Scale Incorporated Chitosan Biocomposite Scaffolds for Bone Tissue Engineering(Elsevier Ltd., 2019) Kara, Aylin; Tamburacı, Sedef; Tıhmınlıoğlu, Funda; Havıtçıoğlu, HasanRecently, biologically active natural macromolecules have come into prominence to be used as potential materials in scaffold design due to their unique characteristics which can mimic the human tissue structure with their physical and chemical similarity. Among them, fish scale (FS) is a biologically active material with its structural similarity to bone tissue due to including type I collagen and hydroxyapatite and also have distinctive collagen arrangement. In the present study, it is aimed to design a novel composite scaffold with FS incorporation into chitosan (CH) matrix for bone tissue regeneration. Therefore, two biological macromolecules, fish scale and chitosan, were combined to produce bio-composite scaffold. First, FS were decellularized with the chemical method and disrupted physically as microparticles (100 in), followed by dispersal in CH with ultrasonic homogenisation, CH/FS scaffolds were fabricated by lyophilization technique. Scaffolds were characterized physically, chemically, mechanically, and morphologically. SEM and porosity results showed that CH/FS scaffolds have uniform pore structure showing high porosity. Mechanical properties and degradation rate are enhanced with increasing FS content. In vitro cytotoxicity, proliferation and osteogenic activity of the scaffolds were evaluated with SaOS-2 cell line. CH/FS scaffolds did not show any cytotoxicity effect and the cells were gradually proliferated during culture period. Cell viability results showed that, FS microparticles had a proliferative effect on SaOS-2 cells when compared to control group. ALP activity and biomineralization studies indicated that FS micro particle reinforcement increased osteogenic activity during culture period. As a biological macromolecule with unique characteristics, FS was found as cytocompatible and provided promising effects as reinforcement agents for polymeric scaffolds. In conclusion, fabricated CH/FS bio-composites showed potential for bone tissue engineering applications. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 20Citation - Scopus: 21Long Term Stability of Biodegradable Polymers on Building Limestone(Elsevier Ltd., 2019) Kaplan, Zişan; Böke, Hasan; Sofuoğlu, Aysun; İpekoğlu, BaşakSynthetic polymers can be replaced by biodegradable ones as adhesives, water repellents and consolidants on the stone surfaces and facades of the historic buildings in their conservation to minimize future deterioration. In this study, the long-term stability of two biodegradable polymers, polyhydroxybutyrate (PHB) and poly-L-lactide (PLA), and an acrylic polymer (Paraloid B72) which is commonly used in conservation works of artefacts, were evaluated on limestone using a UV lamp-weathering chamber (up to 104 days) for future protection studies. Chemical and morphological changes induced by an accelerated weathering test were examined by Fourier Transform Infrared spectroscopy (FT-IR) and Scanning Electron Microscopy (SEM) analyses. Protection efficiency of the polymers was determined by the changes in color, capillary water absorption, static contact angle on limestone. Paraloid B72, PHB, and PLA coatings significantly increased hydrophobicity while decreasing capillarity water absorption and caused negligible change in the color of the limestone. Protection efficiencies of PLA and PHB polymers were almost the same as that of Paraloid B72, a widely used acrylic polymer. However, PLA and PHB seemed to be favorable polymers as protective agents due to their reversibility and biodegradability, low chromatic changes, good hydrophobic behavior and good stability to weathering in reducing the effects of outdoor exposure on limestone surfaces.Article Citation - WoS: 25Citation - Scopus: 26Lowering the Sintering Temperature of Solid Oxide Fuel Cell Electrolytes by Infiltration(Elsevier Ltd., 2019) Sındıraç, Can; Çakırlar, Seda; Büyükaksoy, Aligül; Akkurt, SedatA dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400-1500 degrees C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 degrees C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 degrees C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.Article Citation - WoS: 24Citation - Scopus: 26Self-Assembly Behavior of the Keratose Proteins Extracted From Oxidized Ovis Aries Wool Fibers(Elsevier Ltd., 2019) Pakkaner, Efecan; Yalçın, Damla; Uysal, Berk; Top, AybenWater soluble keratose proteins were obtained from an Ovis Aries wool using peracetic acid oxidation. The wool samples and the extracted keratose proteins were characterized by using FTIR, XRD, SEM and TGA techniques. Fractions of alpha-keratose (MW = 43-53 kDa) along with protein species with molecular weights between 23 kDa and 33 kDa were identified in the SDS-PAGE analysis result of the extracted protein mixture. DLS and AFM experiments indicated that self-assembled globular nanoparticles with diameters between 15 nm and 100 nm formed at 5 mg/ml keratose concentration. On the other hand, upon incubation of 10 w % keratose solutions at 37 degrees C and 50 degrees C, interconnected keratose hydrogels with respective storage modulus (G') values of 0.17 +/- 0.03 kPa and 3.7 +/- 0.5 kPa were obtained. It was shown that the keratose hydrogel prepared at 37 degrees C supported L929 mouse fibroblast cell proliferation which suggested that these keratose hydrogels could be promising candidates in soft tissue engineering applications. (C) 2018 Elsevier B.V. All rights reserved.Article Citation - WoS: 23Citation - Scopus: 24Investigation of Kinetics of Supercritical Drying of Alginate Alcogel Particles(Elsevier Ltd., 2019) Şahin, İbrahim; Uzunlar, Erdal; Erkey, CanSpherical calcium alginate gel particles were synthesized by dripping method. The effects of temperature, pressure, particle size and CO2 flow rate on kinetics of supercritical drying of alginate gel particles in a packed bed were investigated. Increase in CO2 flow rate, increase in temperature and decrease in particle size increased the drying rate and decreased the drying time. A mathematical model based on (i) the diffusion of the solvent inside the pores of gel particles, (ii) external mass transfer of the solvent from the surface of the gel particles into the flowing fluid stream, and (iii) convection and axial dispersion of the solvent in the flowing fluid stream was developed. A correlation for predicting external mass transfer coefficients for supercritical drying of alcogel particles was developed by fitting the model to experimental data. A good agreement between the experimental data and model results was achieved using the developed correlation.Article Citation - WoS: 27Citation - Scopus: 31Fluoroacrylate-Aromatic Acrylate Copolymers for Viscosity Enhancement of Carbon Dioxide(Elsevier Ltd., 2019) Kılıç, Sevgi; Enick, Robert M.; Beckman, Eric J.The effect of the structure of aromatic acrylate-fluoroacrylate copolymers on CO2 viscosity at elevated pressures was investigated. These copolymers were all found to be miscible with CO2 at pressures between 10-15 MPa (295 K) and induce an increase in the viscosity to some degree. It appears that stacking of aromatic rings is the key factor in viscosity enhancement. The results showed that viscosity of the solution increases with the increasing content of the aromatic acrylate unit in the copolymer, but a point is reached beyond which additional comonomer causes the relative viscosity to drop, suggesting that the aromatic rings associate through intramolecular rather than intermolecular interactions beyond the optimum value. The most effective CO2 thickener identified in this study was the 29% phenyl acrylate-71% fluoroacrylate copolymer. However, the presence of a spacer (methyl or ethyl) between the backbone and the aromatic group substantially diminished the viscosity enhancement.Article Citation - WoS: 12Citation - Scopus: 13Development of Agcl-Tio2 Xerogels Entrapped Antibacterial Polyacrylonitrile Membranes: the Effect of High Salinity Water on Silver Release, Antibiofouling and Antibacterial Efficacies(Elsevier Ltd., 2020) Uz, Metin; Yaşar Mahlıçlı, Filiz; Şeker, Erol; Alsoy Altınkaya, SacideSilver-containing antibacterial membranes are commonly used to control biofouling during bacteria filtration. Unfortunately, fast and uncontrolled release of silver to water is a challenge since this causes mass accumulation of silver in water resources and insufficient long-term antimicrobial effect. To overcome these disadvantages, we propose to add AgCl-TiO2 xerogels (0–0.8 wt%) in the polyacrylonitrile membranes. The long-term silver retaining of the membranes was evaluated by measuring the silver release under filtration of deionized water in the absence and the presence of 1 M NaCl up to 5 days. The antibiofouling and the antibacterial efficacies were determined by measuring the changes in antibacterial activity and DI water flux of the membranes at the end of 5 days of E. coli filtration. The 0.2 wt% AgCl-TiO2 xerogel incorporated polyacrylonitrile membrane demonstrated a constant ~1 ?g of silver release/cm2 per filtration cycle after a total filtration of 0.05 L/cm2 with 1 M NaCl solution. Additionally, it showed antibacterial efficacy and ~100% recovery of deionized water flux by simple backwashing with water after having been used in many E. coli filtration cycles. Thus, this membrane could potentially be used up to ~5.8 years for 8000 h a year for the filtration of high salinity water. Statement of novelty: Silver-containing antibacterial membranes are commonly used to control biofouling during bacteria filtration. Uncontrolled release of silver from the membrane causes massive silver accumulation in water which in turn leads to contamination of water resources and threat to aquatic organisms. Although silver release is strongly influenced by the salinity of water, the release data was collected through filtration of pure DI water or tap water in literature. To overcome the shortcomings of the published studies, we propose to use AgCl-TiO2 xerogels in membranes due to low solubility of AgCl in water and measure the release by filtering high-salinity water. © 2020 Elsevier B.V.Article Citation - WoS: 8Citation - Scopus: 8Synthesis of Butyl Glucoside Over Sulphated Zr-Sba and Tungstophosphoric Acid Incorporated Sba-15 Catalysts(Elsevier Ltd., 2021) Mutlu, Nahide Nuran; Yılmaz, SelahattinGlycosidation of glucose with n-butanol was studied over sulphated Zr incorporated SBA-15 and tungstophosphoric acid (TPA) incorporated SBA-15 catalysts. The catalysts were prepared with different Zr, TPA and SO4 amounts via hydrothermal synthesis. SBA-15 structure was preserved and Zr and TPA were successfully incorporated. Sulphation improved the acidity of Zr-SBA-15 and the ratio of Brønsted to Lewis acid sites (B/L) increased. Thus, much higher butyl glucoside yields (about 70 %) were obtained over SO4/Zr-SBA-15 catalysts. However, 15 % activity loss was observed after 2 re-use due to sulphate leaching. TPA-SBA-15 catalysts had the highest B/L and provided very high catalytic activity with butyl glucoside yields above 95 %. The initial rate of butyl glucoside formation over TPA-SBA-15 catalysts were close to that of H2SO4. These catalysts were found stable and reusable. Reaction temperature and catalysts amount was studied as the reaction parameters over the most active and selective catalyst. © 2020 Elsevier B.V.