Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
68 results
Search Results
Now showing 1 - 10 of 68
Article Effective Synthesis of Cetyl Palmitate Over Co-Precipitated Wo3-Zro2 Catalysts(Springer Verlag, 2018) Mutlu, Vahide N.; Yılmaz, SelahattinThis study is focused on the development of solid acid catalysts for the synthesis of long chain fatty acids. A series of WO3-ZrO2 catalysts were prepared by co-precipitation method and tested in the synthesis of cetyl palmitate. The effect of WO3 loading (10, 15, and 20 wt% WO3) and calcination temperature (700 and 800 degrees C) on the catalyst properties and activity was investigated. XRD and Raman analysis confirmed that WO3 loading stabilized the tetragonal zirconia phase. Higher calcination temperature enhanced the acidities of the catalysts. WO3-ZrO2 catalysts were found to be very efficient for the synthesis of cetyl palmitate with high selectivity. These catalysts were tested for different reaction temperatures (135 and 162 degrees C), feed composition and catalyst amounts. The highest cetyl palmitate yield (98.4%) was obtained over the catalyst calcined at 800 degrees C with 15 wt% WO3, which had the highest total acidity. The catalysts preserved their activities up to three reuse.Article Citation - WoS: 6Citation - Scopus: 6Esterification of 1-Octanol on Clinoptilolite-Supported Tio2 Catalysts(Springer Verlag, 2019) Özyağcı, Bensu; Şahin, Volkan; Karabakan, AbdulkerimIn this study, a natural type of zeolite, Clinoptilolite (CLI), is used as a support for TiO2. First, TiO2-supported heterogeneous catalysts originated from the high temperature calcination of TiCl4 groups, which were thermally immobilized on clinoptilolite, were obtained. Powder-XRD and EDX analyzes showed that the oxide form of Ti-immobilized on dealuminated clinoptilolite were formed in the anatase phase, and the zeolite structure was preserved. As seen in TGA/DTA analyzes, this catalyst could be efficient and have high stability for many reactions. Second, the esterification reaction of 1-octanol with acetic acid is used as a reference reaction for this catalyst.Article Citation - WoS: 4Citation - Scopus: 4Novel Hybrid Process for the Conversion of Microcrystalline Cellulose To Value-Added Chemicals: Part 3: Detailed Reaction Pathway(Springer Verlag, 2019) Akın, Okan; Yüksel, AslıIn this study, a novel method of hydrothermal electrolysis of microcrystalline cellulose (MCC) under sub-critical water conditions (200 degrees C) was investigated by applying direct current at constant voltage with the presence of acid catalyst of 5mMH(2)SO(4). Direct current at constant voltage of 2.5V, 4.0V and 8.0V was applied between cylindrical anode (titanium) and cathode (reactor wall). Hydrothermal electrolysis reactions were carried out in a batch reactor (450mL-T316) for the reaction time of 240min. Decomposition products of MCC were analyzed by GC-MS and the decomposition pathway of cellulose under applied voltage was postulated. Levoglucosan and levoglucosenone formations were detected as the first hydrolysis products of MCC and further hydrolysis yielded to formation of glucose and fructose. The major decomposition products of cellulose were detected as levulinic acid (LA), 5-HMF and furfural. Further reactions of LA such as electrochemical decarboxylation, dehydration, hydrogenation, resulted in the formation of 2-butanone, 2-butanone-3-hydroxy, gamma-valerolactone, respectively. Most dramatic results on the product distribution were obtained at applied 2.5V voltage in which LVA and 5-HMF were selectively produced. [GRAPHICS] .Article Citation - WoS: 64Citation - Scopus: 78Utilization of Municipal Plastic and Wood Waste in Industrial Manufacturing of Wood Plastic Composites(Springer Verlag, 2020) Başalp, Dildare; Tıhmınlıoğlu, Funda; Sofuoğlu, Sait Cemil; İnal, Fikret; Sofuoğlu, AysunIn this study, Wood Plastic Composites (WPCs) were produced from post-consumer bulky wastes of recycled plastic and wood in order to minimize waste, decrease environmental effects of plastics, reserve natural resources, and support circular economy for sustainable production and consumption. Five different types of polypropylene (PP) or polyethylene (PE) based recycled plastics and wood obtained from urban household bulky wastes were used in the production of recycled WPC composites, r-WPCs. Virgin WPC (v-WPC) and r-WPC compounds were prepared with wood flour (WF) and maleic anhydride grafted compatibilizer (MAPP or MAPE) to evaluate the effect of recycled polymer type and compatibilizer on the mechanical properties. It was found that tensile strength properties of r-WPCs produced from recycled PP (r-PP) were higher than that of the r-WPCs produced from mixed polyolefins and recycled PE. r-WPCs containing anti-oxidants, UV stabilizers, and compatibilizer with different WF compositions were produced from only recycled garden fraction PP (PPFGF) to determine the optimum composition and processing temperature for pilot scale manufacturing of r-WPCs. Based on tensile, impact, flexural, and water sorption properties of r-WPC compounds with different formulations, the optimum conditions of r-WPC compounds for industrial manufacturing process were determined. Surface morphology of fractured surfaces as well as tensile, flexural and density results of r-WPC compounds revealed the enhancement effect of MAPP on interfacial adhesion in r-WPCs. r-WPC products (crates and table/chair legs) based on bulky wastes were produced using an injection molding process at industrial scale by using 30 wt% WF-filled r-WPC compound. This study demonstrated that r-WPC compounds from recycled bulky plastic and wood wastes can be used as a potential raw material in plastic as well as WPC industry, contributing to circular economy. GraphicArticle Citation - WoS: 19Citation - Scopus: 29Modeling of an Activated Sludge Process for Effluent Prediction—a Comparative Study Using Anfis and Glm Regression(Springer Verlag, 2018) Araromi, Dauda Olurotimi; Majekodunmi, Olukayode Titus; Adeniran, Jamiu Adetayo; Salawudeen, Taofeeq OlalekanIn this paper, nonlinear system identification of the activated sludge process in an industrial wastewater treatment plant was completed using adaptive neuro-fuzzy inference system (ANFIS) and generalized linear model (GLM) regression. Predictive models of the effluent chemical and 5-day biochemical oxygen demands were developed from measured past inputs and outputs. From a set of candidates, least absolute shrinkage and selection operator (LASSO), and a fuzzy brute-force search were utilized in selecting the best combination of regressors for the GLMs and ANFIS models respectively. Root mean square error (RMSE) and Pearson’s correlation coefficient (R-value) served as metrics in assessing the predicting performance of the models. Contrasted with the GLM predictions, the obtained modeling results show that the ANFIS models provide better predictions of the studied effluent variables. The results of the empirical search for the dominant regressors indicate the models have an enormous potential in the estimation of the time lag before a desired effluent quality can be realized, and preempting process disturbances. Hence, the models can be used in developing a software tool that will facilitate the effective management of the treatment operation.Article Citation - WoS: 32Citation - Scopus: 37Mcdm Analysis of Wind Energy in Turkey: Decision Making Based on Environmental Impact(Springer Verlag, 2018) Değirmenci, Sinem; Bingöl, Ferhat; Sofuoğlu, Sait CemilDevelopment of new wind energy projects require complex planning process involving many social, technical, economic, environmental, political concerns, and different agents such as investors, utilities, governmental agencies, or social groups. The aim of this study is to develop a tool combining Geographic Information System (GIS) and Multi-Criteria Decision-Making (MCDM) methodologies, and its application for Turkey as a case study. A variety of constraints and criteria were identified based on a literature review and regulations gathered from variety of agencies, use of which resulted in determination of infeasible sites. Then, pairwise comparisons were carried out using analytic hierarchy process as the MCDM method to estimate relative importance of the criteria, and to visualize a suitability map with three classes. As the final stage, decision making was carried out based on environmental impact where 45.5% of the Turkish territory was found as infeasible area. Sixty percent of the remaining area are covered by the moderate suitability class, followed by the highly suitable area (20.3%) and low suitable area (19.8%). The output of this study can be used by energy planners to estimate the extent that wind energy can be developed based on public perception, administrative, and environmental aspectsArticle Citation - WoS: 12Citation - Scopus: 12Peg and Peg-Peptide Based Doxorubicin Delivery Systems Containing Hydrazone Bond(Springer Verlag, 2018) Balcı, Beste; Top, AybenmPEG and mPEG-peptide based drug delivery systems were prepared by conjugating doxorubicin (DOX) to these carrier molecules via hydrazone bond. The peptide, AT1, with a sequence of CG3H6G3E served as mPEG and doxorubicin attachment site. Histidines were incorporated to the sequence to improve pH responsiveness of the carrier molecule. Hydrodynamic diameters (mean sizes) of mPEG-based drug delivery system (mPEG-HYD-DOX) were measured as 9 ± 0.5 and 7 ± 0.5 nm at pH 7.4 and pH 5.0, respectively. Mean size of the aggregates of the peptide containing drug delivery system, mPEG-AT1-DOX, was determined as 12 ± 2 nm at neutral pH. At pH 5.0, on the other hand, mPEG-AT1-DOX exhibited a size distribution between 20 and 100 nm centered at about 40 nm. Comparison of % DOX release values of the drug delivery systems obtained at pH 7.4 and pH 5.0 indicated that mPEG-AT1-DOX has enhanced pH sensitivity. DOX equivalent absolute IC50 values were obtained as 0.96 ± 0.51, 21.9 ± 5.9, and 5.55 ± 0.75 μg/mL for free DOX, mPEG-HYD-DOX, and mPEG-AT1-DOX, respectively. Considering more pronounced pH sensitivity and cytotoxicity of mPEG-AT1-DOX, the use of both pH responsive functional groups and acid cleavable chemical bond between the carrier molecule and drug can be a promising approach in the design of drug delivery systems for cancer therapy.Article Citation - WoS: 23Citation - Scopus: 27Novel Poss Reinforced Chitosan Composite Membranes for Guided Bone Tissue Regeneration(Springer Verlag, 2018) Tamburacı, Sedef; Tıhmınlıoğlu, FundaIn this study, novel composites membranes composed of chitosan matrix and polyhedral oligomeric silsesquioxanes (POSS) were fabricated by solvent casting method. The effect of POSS loading on the mechanical, morphological, chemical, thermal and surface properties, and cytocompatibility of composite membranes were investigated and observed by tensile test, atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), protein adsorption assay, air/water contact angle analysis and WST-1 respectively. Swelling studies were also performed by water absorption capacity determination. Results showed that incorporation of Octa-TMA POSS® nanofiller to the chitosan matrix increased the surface roughness, protein adsorption and swelling capacity of membranes. The addition of POSS enhanced significantly the ultimate tensile strength and strain at break of the composite membranes up to 3 wt% POSS loaded samples. An increase of about 76% in tensile strength and of strain at break 1.28% was achieved for 3 wt% POSS loaded nanocomposite membranes compared with chitosan membranes. The presence of POSS filler into polymer matrix increased the plasma protein adsorption on the surface. Maximum protein capacity and swelling was obtained for 10 wt% loaded samples. High cell viability results were obtained with indirect extraction of chitosan/POSS composites. Besides, cell proliferation and ALP activity results showed that POSS incorporation significantly increased the ALP activity of Saos-2 cells cultured on chitosan membranes. This novel composite membranes with tunable properties could be considered as a potential candidate for guided bone regeneration applicationsArticle Citation - WoS: 34Citation - Scopus: 36Effects of Organo-Modified Clay Addition and Temperature on the Water Vapor Barrier Properties of Polyhydroxy Butyrate Homo and Copolymer Nanocomposite Films for Packaging Applications(Springer Verlag, 2018) Akın, Okan; Tıhmınlıoğlu, FundaPolymer nanocomposites, based on bacterial biodegradable thermoplastic polyester, poly(hydroxy-butyrate) (PHB), poly(hydroxyl-butyrate-co-hydroxy-valerate) (PHBHV), and commercial organo-modified montmorillonite (OMMT-Cloisite 10A) were prepared by solution casting method. This work aims to investigate the effect of Cloisite 10A type clay addition on the water vapour permeability properties of PHB/OMMT, and PHBHV/OMMT nanobiocomposite films. Temperature dependence of water vapor permeabilities of the films were also evaluated at various temperatures, and semi empirical permeability models were used to predict the permeability of polymer systems as a function of clay concentration and aspect ratio of nanoplates. Moreover, thermal, optical, and mechanical properties of the composites were examined by using varieties of techniques including differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), scanning electron microscope (SEM), and thin-film X-ray diffractometer (TF-XRD) respectively. Test results indicated that addition of highly intergallery swollen Cloisite 10A to the PHB/PHBHV, reduced the water vapor permeability up to 41 and 25% compared to native PHB and PHBHV films, respectively. Regarding the all mechanical properties measured, the maximum improvement was achieved for 3 wt% clay loaded samples for both PHB and PHBHV polymer composites. An increase of about 152 and 73% in tensile strength and of 77 and 18% in strain at break was achieved for PHB and PHBHV polymers, respectively. As a result of X-ray diffraction analysis, exfoliated structure was achieved at low clay loaded sample (1% w/w), however at higher concentration (3% w/w) the structure found as intercalated. Therefore, it is an evident that enhancement of characteristic properties highly depend on the dispersion level of clay particles in polymer matrix. The results obtained in this study show the feasibility of improvement of the properties of PHB based polymers with incorporation of nanoclay.Article Citation - WoS: 18Citation - Scopus: 21Polybrominated Diphenyl Ethers (pbdes) in Background Air Around the Aegean: Implications for Phase Partitioning and Size Distribution(Springer Verlag, 2017) Besis, Athanasios; Lammel, Gerhard; Kukucka, Petr; Samara, Constantini; Sofuoğlu, Aysun; Dumanoğlu, Yetkin; Eleftheriadis, Kostas; Kouvarakis, Giorgos; Sofuoğlu, Sait Cemil; Vassilatou, Vassiliki; Voutsa, DimitraThe occurrence and atmospheric behavior of tri- to deca-polybrominated diphenyl ethers (PBDEs) were investigated during a 2-week campaign concurrently conducted in July 2012 at four background sites around the Aegean Sea. The study focused on the gas/particle (G/P) partitioning at three sites (Ag. Paraskevi/central Greece/suburban, Finokalia/southern Greece/remote coastal, and Urla/Turkey/rural coastal) and on the size distribution at two sites (Neochorouda/northern Greece/rural inland and Finokalia/southern Greece/remote coastal). The lowest mean total (G + P) concentrations of ∑7PBDE (BDE-28, BDE-47, BDE-66, BDE-99, BDE-100, BDE-153, BDE-154) and BDE-209 (0.81 and 0.95 pg m−3, respectively) were found at the remote site Finokalia. Partitioning coefficients, KP, were calculated, and their linear relationships with ambient temperature and the physicochemical properties of the analyzed PBDE congeners, i.e., the subcooled liquid pressure (PL°) and the octanol-air partition coefficient (KOA), were investigated. The equilibrium adsorption (PL°-based) and absorption (KOA-based) models, as well as a steady-state absorption model including an equilibrium and a non-equilibrium term, both being functions of log KOA, were used to predict the fraction Φ of PBDEs associated with the particle phase. The steady-state model proved to be superior to predict G/P partitioning of BDE-209. The distribution of particle-bound PBDEs across size fractions < 0.95, 0.95–1.5, 1.5–3.0, 3.0–7.2, and > 7.2 μm indicated a positive correlation between the mass median aerodynamic diameter and log PL° for the less brominated congeners, whereas a negative correlation was observed for the high brominated congeners. The potential source regions of PBDEs were acknowledged as a combination of long-range transport with short-distance sources.