Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
8 results
Search Results
Now showing 1 - 8 of 8
Article Citation - WoS: 37Citation - Scopus: 41Processing and Characterization of Geopolymer and Sintered Geopolymer Foams of Waste Glass Powders(Elsevier, 2021) Polat, Dilan; Güden, MustafaGeopolymer foams of fine and coarse waste glass (WG) powders were prepared using an activation solution of NaOH (8 M) and Na2SiO3. The effects of WG powder particle size, solid/liquid ratio (S/L = 1, 1.5, and 2) and Al foaming agent content (2-20 wt%) on the expansion and temperature behavior of the slurries were determined in-situ using a laser sensor and a thermocouple, respectively. The geopolymer foams processed using a coarse WG powder slurry, S/L = 2, and 2 wt% Al, were further sintered at 600, 700, 725, and 750 degrees C. The compression strengths and thermal conductivities of the geopolymer and sintered geopolymer foams were also determined. The slurry expansions continued until about a maximum, and the temperatures of the slurries increased to a maximum, 85-88 degrees C. At the maximum temperature, the slurry evaporation and the resultant increase in the S/L ratio limited the slurry expansion. Increasing the Al content decreased the final density of the foams (238-555 kg m-3), while the coarse powder slurries resulted in lower densities than the fine powder slurries. Three crystal phases, muscovite, sodium aluminum silicate hydrate, and thermonitrite, were determined in the geopolymer foams. The muscovite formation was noted to be favored at high S/L ratios. During sintering, the partial melting of glass particles started after about 700 degrees C, while sintering above this temperature decreased the final density of the foams. The reduced density above 700 degrees C was ascribed to the release of CO2 due to the decomposition of thermonitrite. Both the compressive strength and thermal conductivity of the geopolymer and sintered geopolymer foams increased with increasing foam density. The highest increase in the compressive strength and reduction in the density were seen in the geopolymer foams sintered at 750 degrees C.Article Citation - WoS: 54Citation - Scopus: 58Sintering and Microstructural Investigation of Gamma–alpha Alumina Powders(Elsevier Ltd., 2014) Yalamaç, Emre; Trapani, Antonio; Akkurt, SedatSintering behaviors of commercially available alumina powders were investigated using constant-heating rate dilatometric experiments. Each powder had different proportion of alpha/gamma alumina. Densification behaviors of powders were studied up to 1600 °C with three different heating rates of 1, 3.3 and 6.6 °C/min. Compacts of different gamma content alumina powders exhibited systematic anomalous second peaks in the densification rate curves at certain heating rates and temperatures. At 3.3 °C/min heating rate experiments, densification curves of 10% gamma phase alumina powder compacts reached a plateau after 1450 °C, and did not increase any further at higher temperatures. This phenomenon was double checked to understand powder behavior during sintering. 10% gamma phase alumina powder compacts showed the highest density for each heating rate. It reached 94% theoretical density with 1 °C/min heating rate. But 20% gamma phase alumina powder compacts had the finest grain size of about 1.40 ?m. Final density and porosity of compacts were also tested by image analysis and the results were coherent with Archimedes results. © 2014 Karabuk UniversityArticle Citation - WoS: 6Citation - Scopus: 6The Expansion Behavior of Slurries Containing Recycled Glass Powder Carboxymethyl Cellulose, Lime and Aluminum Powder(Elsevier, 2020) Zeren, Doğuş; Şentürk, Ufuk; Güden, MustafaThe rheology and foaming/expansion of the slurries of a waste/recycled glass powder with 50, 55 and 60 wt% of solid (glass powder) were experimentally investigated. The glass powder slurries were foamed using aluminum powder as foaming agent (0.75 wt%) and calcium hydroxide as activator (1 wt%). Sodium carboxymethyl cellulose (CMC) was added to the slurries as a binder with the amounts between 0 and 4 wt%. The expansions of the slurries were measured in-situ using a laser sensor and reported as percent volume expansion. The CMC-addition increased the viscosities of the slurries, particularly the fine size powder slurries. The slurries with the relatively low-viscosity exhibited lower initial expansion rates compared to the slurries with the relatively high-viscosity. The maximum expansions of the slurries increased from 300 to 350%, when the viscosity increased to 5 Pa s and reached a steady value around 400% between 5 and 50 Pa s. The expansions of the slurries could not be achieved above 50 Pa s since they became too thick to be foamed. The foam samples made from the slurries with 55 and 60 wt% of solid and sintered at 700 and 750 degrees C for 30 min had the average densities between 355 and 530 kg m(-3) and the average compressive strengths between 0.2 and 0.5 MPa. Increasing sintering time to 60 min at 750 degrees C increased the average compressive strength from 0.5 to 1.5 MPa for the foam samples made from the slurry with 60 wt% of solid. These proved that both sintering temperature and time were effective in increasing the compressive strengths of the foamed structures. The thermal conductivities of the sintered foam samples with the densities of 355 and 504 kg m(-3) were measured 0.042 and 0.057 W m(-1) K-1, respectively. (C) 2019 Elsevier Ltd. All rights reserved.Article Citation - WoS: 14Citation - Scopus: 14Microstructural Development of Interface Layers Between Co-Sintered Alumina and Spinel Compacts(Elsevier Ltd., 2011) Yalamaç, Emre; Carry, Claude; Akkurt, SedatTests were performed to investigate the microstructure of the interface between alumina and spinel materials after high temperature thermal treatment (1500°C). The first test involved co-sintering of co-pressed alumina and spinel compacts. Microstructures were investigated by SEM, EDS, WDS and EBSD. A microstructurally distinct layer with columnar grains of up to 40μm length and 5μm width was observed after 16h at 1500°C. Growth rate of the columnar spinel grains from parent spinel towards alumina follows parabolic kinetics, controlled by a mixed process of O2- ion diffusion and interface reaction. Diffusion couples of spinel and alumina were investigated. Same columnar spinel grains were observed at the interface which grew into alumina during thermal treatment with the same kinetics as in co-sintering experiments. The shape of the phase boundaries between spinel and alumina can be a further indication of the direction of their growth.Article Citation - WoS: 25Citation - Scopus: 25Characterization Investigations During Mechanical Alloying and Sintering of W-20 Vol% Sic Composites(Elsevier Ltd., 2010) Coşkun, Selim; Öveçoğlu, M. Lütfi; Özkal, Burak; Tanoğlu, MetinThe effect of mechanical alloying and the sintering regime on the microstructural and the physical properties of W-SiC composites were investigated. Powder mixtures of W-20 vol.% SiC were mechanically alloyed (MA'd) using a Spex mill for 3 h, 6 h and 24 h. MA'd powders were characterized by Laser Diffraction Particle Size Analyzer, SEM and XRD investigations. MA'd W-20 vol.% SiC powder composites were sintered under inert Ar and reducing H2 gas conditions at 1680 °C and 1770 °C for 1 h. The microstructural and mechanical characterizations of the sintered samples were carried out by scanning electron microscope (SEM) and X-ray diffraction (XRD) and Vickers Hardness analyses. The addition of SiC remarkably increases the hardness of the composites. Hardness is also increased with decreasing grain size and increasing amount of MA. © 2009 Elsevier B.V. All rights reserved.Article Citation - WoS: 12Citation - Scopus: 12The Effect of Strain Rate on the Compressive Deformation Behavior of a Sintered Ti6al4v Powder Compact(Elsevier Ltd., 2008) Taşdemirci, Alper; Hızal, Alpay; Altındiş, Mustafa; Hall, Ian W.; Güden, MustafaThe high strain rate (220–550 s−1) and quasi-static (0.0016 s−1) compression deformation behavior of a sintered Ti6Al4V powder compact was investigated. The compact was prepared using atomized spherical particles (100–200 μm) and contained 38 ± 1% porosity. The deformation sequences of the tested samples were further recorded by high speed camera and analyzed as a function of strain. The failure of the compact, which was found to be similar in the studied high strain rate and quasi-static strain rate testing regimes, occurs through particle decohesion along the surface of the two cones in a ductile (dimpled) mode consisting of void initiation and growth and by void coalescence in the interparticle bond region. The effect of strain rate was to increase the flow stress and compressive strength of the compact while the critical strain corresponding to the maximum stress was shown to be strain rate independent.Article Citation - WoS: 60Citation - Scopus: 70Foam Glass Processing Using a Polishing Glass Powder Residue(Elsevier Ltd., 2013) Attila, Yiğit; Güden, Mustafa; Taşdemirci, AlperThe foaming behavior of a powder residue/waste of a soda-lime window glass polishing facility was investigated at the temperatures between 700 and 950 °C. The results showed that the foaming of the glass powder started at a characteristic temperature between 670 and 680 °C. The maximum volume expansions of the glass powder and the density of the foams varied between 600% and 750% and 0.206 and 0.378 g cm−3, respectively. The expansion of the studied glass powder residue resulted from the decomposition of the organic compounds on the surfaces of the glass powder particles, derived from an oil-based coolant used in the polishing. The collapse stress of the foams ranged between ∼1 and 4 MPa and the thermal conductivity between 0.048 and 0.079 W K−1 m−1. Both the collapse stress and thermal conductivity increased with increasing the foam density. The foams showed the characteristics of the compression deformation of the open cell brittle foams, which was attributed to the relatively thick cell edges.Article Citation - WoS: 41Citation - Scopus: 49Compression Testing of a Sintered Ti6al4v Powder Compact for Biomedical Applications(Elsevier Ltd., 2005) Güden, Mustafa; Çelik, Emrah; Akar, Egemen; Çetiner, SinanIn this study, the compression deformation behavior of a Ti6Al4V powder compact, prepared by the sintering of cold compacted atomized spherical particles (100–200 Am) and containing 36–38% porosity, was investigated at quasi-static (1.6 10 3–1.6 10 1 s 1) and high strain rates (300 and 900 s 1) using, respectively, conventional mechanical testing and Split Hopkinson Pressure Bar techniques. Microscopic studies of as-received powder and sintered powder compact showed that sintering at high temperature (1200 8C) and subsequent slow rate of cooling in the furnace changed the microstructure of powder from the acicular alpha (a) to the Widmanst7tten (a+h) microstructure. In compression testing, at both quasi-static and high strain rates, the compact failed via shear bands formed along the diagonal axis, 458 to the loading direction. Increasing the strain rate was found to increase both the flow stress and compressive strength of the compact but it did not affect the critical strain for shear localization. Microscopic analyses of failed samples and deformed but not failed samples of the compact further showed that fracture occurred in a ductile (dimpled) mode consisting of void initiation and growth in a phase and/or at the a/h interface and macrocracking by void coalescence in the interparticle bond region.