Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 18Citation - Scopus: 18The Effects of the Post-Annealing Time on the Growth Mechanism of Bi2sr2ca1cu2o8+ Thin Films Produced on Mgo (100) Single Crystal Substrates by Pulsed Laser Deposition (pld)(Elsevier Ltd., 2016) Nane, Onur; Özçelik, Bekir; Abukay, DoğanBi2Sr2Ca1Cu2O8+δï thin films were deposited on MgO (100) substrates by pulsed laser deposition (PLD). The effects of post-annealing time on the phase formation, the structural and superconducting properties of the films have been investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature dependent resistivity (R-T), atomic force microscopy (AFM), and DC magnetization measurements. The films deposited at 600 °C were post-annealed in an atmosphere of a gas mixture of Ar (93%) and O2 (7%), at 860 °C for 10, 30, and 60 min. All films have demonstrated a mainly single phase of 2212 with a high crystallinity (FWHM0.159°) and c-axis oriented. The critical temperature, TC, of the films annealed for 10, 30, and 60 min were obtained as 77, 78, and 78 K, respectively. The highest critical current density, JC, was calculated as 3.34×107 A/cm2 for the film annealed at 860 °C for 30 min at 10 K.Article Citation - WoS: 9Citation - Scopus: 10The Effects of the Post-Annealing Temperature on the Growth Mechanism of Bi2sr2ca1cu2o8+ ? Thin Films Produced on Mgo (1 0 0) Single Crystal Substrates by Pulsed Laser Deposition (pld)(Elsevier Ltd., 2013) Nane, O.; Özçelik, Bekir; Abukay, DoğanThe effects of post-annealing temperature were investigated on Bi 2Sr2Ca1Cu2O8+ ∂ thin films deposited on MgO (1 0 0) substrates by pulsed laser deposition (PLD). The structural and superconducting properties of the films have been determined by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature dependent resistivity (R-T), and DC magnetization measurements. The films which were deposited at 600 C were post-annealed in an atmosphere of a gas mixture of Ar (93%) and O2 (7%), at temperature ranging between 800 and 880 C. This resulted in films which exhibited a single phase of 2212 with a high crystallinity (FWHM ≈ 0.16) and texturing along the c-axis, perpendicular to the plane of the substrate. An optimum temperature of 860 C was found for the post-annealing thermal treatment. The critical temperature, TC, of the films was measured as 82 K and the critical current density, JC, was calculated as 3 × 107 A/cm2 for the film annealed at 860 C.Article Citation - WoS: 2Citation - Scopus: 4Signal Performance of Dc-Squids With Respect To Ybco Thin Film Deposition Rate(Elsevier Ltd., 2009) Avcı, İlbeyi; Algül, Berrin Pınar; Akram, Rizwan; Bozbey, Ali; Tepe, Mustafa; Abukay, DoğanThe signal performances of YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (DC-SQUIDs) have been investigated as a function of the thin film structure affected by the growth process. YBCO thin films of 200 nm thicknesses were deposited by DC magnetron sputtering using different deposition rates between 1.0 nm/min and 2.0 nm/min onto 24° bicrystal SrTiO3 (STO) substrates. The thin film samples were subsequently analyzed by XRD and AFM in order to determine their crystalline structures and surface morphologies respectively. The 67 pH directly coupled DC-SQUIDs with 4 μm-wide bicrystal Josephson junctions were fabricated, and characterized with respect to their device performances. The variations in the critical current (Ic), the voltage modulation depth (ΔV) and the noise performance of DC-SQUIDs were reported. The SQUIDs having relatively low deposition rate of 1.0 nm/min was observed to have larger voltage modulation depth as well as higher critical current than that of the samples having larger rate of 2.0 nm/min. The better noise performances were observed as the film deposition rate decreases. The results were associated with the thin film structure and the SQUID characteristics.