Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 14Citation - Scopus: 15Chitosan-Immobilized Pumice for the Removal of As(v) From Waters(Springer Verlag, 2014) Turan, Dilek; Kocahakimoğlu, Cemre; Boyacı, Ezel; Sofuoğlu, Sait Cemil; Eroğlu, Ahmet EminA novel sorbent, chitosan-immobilized pumice, has been prepared for the sorption of As(V) from waters prior to its determination by hydride generation atomic absorption spectrometry. The success of the immobilization has been checked with such characterization techniques as scanning electron microscopy, thermal gravimetric analysis, and elemental analysis. Points of zero charge of the sorbents were determined with potentiometric mass titration. Batch-type equilibration studies have shown that the novel sorbent can be employed at a wide pH range resulting in quantitative sorption (>90 %) at pH 3.0-7.0 and greater than 70 % sorption at pH >8.0. These results demonstrate the advantage of immobilizing chitosan onto pumice, because, under the same conditions, pumice displays <20 % sorption toward As(V), whereas chitosan gives approximately 90%sorption only at pH 3.0. The validity of the method was verified through the analysis of ultrapure, bottled drinking, and tap water samples spiked with arsenate; the respective sorption percentages of 93.2 (±0.7), 89.0 (±1.0), and 80.9 (±1.3) were obtained by batch-type equilibration. Arsenic sorption was also examined in the presence of common interfering ions resulting in competing effects of PO3- 4 and NO- 3on As(V) adsorption.Article Citation - WoS: 16Citation - Scopus: 17Electrospun Amino-Functionalized Pdms as a Novel Spme Sorbent for the Speciation of Inorganic and Organometallic Arsenic Species†(Royal Society of Chemistry, 2013) Boyacı, Ezel; Horzum, Nesrin; Çağır, Ali; Demir, Mustafa Muammer; Eroğlu, Ahmet EminSol–gel based amine-functionalized SPME fibers (PDMS-weak anion exchanger) were prepared and used for direct mode extraction of dimethylarsinic acid (DMA), monomethylarsonic acid (MMA), and arsenate (As(V)) from aqueous solutions followed by HPLC-ICPMS determination. Two different methods of coating were employed: (i) electrospinning and (ii) dip coating. Electrospinning was used for the first time for preparation of sol–gel based SPME fibers and was found to be superior in terms of extracted amount of arsenicals, coating homogeneity, accessibility of amine groups on the surface, and preparation time for a single fiber. Various parameters such as solution pH, extraction time, agitation speed, extraction temperature, and ionic strength were studied. Optimum extraction conditions were determined as pH of 5.0, extraction time of 30 min, agitation speed of 700 rpm, and extraction temperature of 20 C. Extraction ability of the novel coating decreased by the addition of NaCl as a consequence of the competition between anionic arsenic species and chloride ions for active sites of the weak anion exchanger. This novel sol–gel coating prepared by electrospinning was found to be promising for SPME applications. Vibrational spectroscopy revealed the alignment of PDMS chains by elongational force under electrospinning process. The chain alignment accordingly orients the pendant amino functional groups perpendicular to the fiber surface, which may develop the free active functional groups available to the medium and lead to the enhancement of the extraction performance. Moreover, the proposed coating strategy through electrospinning might be able to break new ground for various applications in analytical chemistry as well as other disciplines.Article Citation - WoS: 70Citation - Scopus: 82Sorption Efficiency of Chitosan Nanofibers Toward Metal Ions at Low Concentrations(American Chemical Society, 2010) Horzum Polat, Nesrin; Boyacı, Ezel; Eroğlu, Ahmet Emin; Shahwan, Talal; Demir, Mustafa MuammerChitosan fibers showing narrow diameter distribution with a mean of 42 nm were produced by electrospinning and utilized for the sorption of Fe(III), Cu(II), Ag(I), and Cd(II) ions from aqueous solutions. The ion concentrations in the supernatant solutions were determined using inductively coupled plasma-mass spectrometry (ICP-MS). The filtration efficiency of the fibers toward these ions was studied by both batch and microcolumn methods. High efficiency in sorption of the metal ions was obtained in the both methods. The effects of sorbent amount (0.10−0.50 mg), shaking time (15−120 min), initial metal ion concentration (10.0−1000.0 μg·L−1), and temperature (25 and 50 °C) on the extent of sorption were examined. The sorbent amount did not significantly alter the efficiency of sorption; however, shaking time, temperature, and metal ion concentration were found to have a strong influence on sorption. By virtue of its mechanical integrity, the applicability of the chitosan mat in solid phase extraction under continuous flow looks promising.Article Citation - WoS: 654Citation - Scopus: 786Green Synthesis of Iron Nanoparticles and Their Application as a Fenton-Like Catalyst for the Degradation of Aqueous Cationic and Anionic Dyes(Elsevier Ltd., 2011) Shahwan, Talal; Abu-Sirriah, Sadieh; Nairat, Muath; Boyacı, Ezel; Eroğlu, Ahmet Emin; Scott, Thomas B.; Hallam, Keith R.Iron nanoparticles were produced using extracts of green tea leaves (GT-Fe NPs). The materials were characterized using TEM, SEM/EDX, XPS, XRD, and FTIR techniques and were shown to contain mainly iron oxide and iron oxohydroxide. The obtained nanoparticles were then utilized as a Fenton-like catalyst for decolorization of aqueous solutions containing methylene blue (MB) and methyl orange (MO) dyes. The related experiments investigated the removal kinetics and the effect of concentration for both MB and MO. The concentrations of dyes in aqueous solution were monitored using ultraviolet–visible (UV–vis) spectroscopy. The results indicated fast removal of the dyes with the kinetic data of MB following a second order removal rate, while those of MO were closer to a first order removal rate. The loading experiments indicated almost complete removal of both dyes from water over a wide range of concentration, 10–200 mg L−1. Compared with iron nanoparticles produced by borohydride reduction, GT-Fe nanoparticles demonstrated more effective capability as a Fenton-like catalyst, both in terms of kinetics and percentage removal.Article Citation - WoS: 46Synthesis, Characterization and Application of a Novel Mercapto- and Amine-Bifunctionalized Silica for Speciation/Sorption of Inorganic Arsenic Prior To Inductively Coupled Plasma Mass Spectrometric Determination(Elsevier Ltd., 2011) Boyacı, Ezel; Çağır, Ali; Shahwan, Talal; Eroğlu, Ahmet EminA bifunctional sorbent, (NH2 + SH)silica, containing both amine and mercapto functionalities was prepared by modification of silica gel with 3-(triethoxysilyl)propylamine and (3-mercaptopropyl)trimethoxysilane. In addition to the bifunctional sorbent, silica gel was modified individually with the functional mercapto- and amino-silanes, and the mono-functional sorbents, namely (SH)silica and (NH2)silica, were also mechanically mixed ((NH2)silica + (SH)silica) for the sake of comparison of sorption performances. It has been demonstrated that (SH)silica shows quantitative sorption only to As(III) at two pH values, 1.0 and 9.0, while (NH2)silica displays selectivity only towards As(V) at pH 3.0. On the other hand, the bifunctional (NH2 + SH)silica possesses the efficient features of the two mono-functionalized sorbents; for example, it retains As(III) at a wider pH range, from 1.0 to at least 9.0 with the exception at pH 2.0, and it also shows quantitative sorption to As(V) at pH 3.0. This property gives the bifunctional (NH2 + SH)silica a better flexibility in terms of sorption performance as a function of solution pH. The mechanically mixed (NH2)silica + (SH)silica exhibits a similar but less efficient sorption behavior compared to the bifunctional sorbent. Desorption of both As(III) and As(V) species can be realized using 0.5 M NaOH. The validity of the proposed method was checked through the analysis of a standard reference material and a good correlation was obtained between the certified (26.67 μg L−1) and determined (27.53 ± 0.37 μg L−1) values. Spike recovery tests realized with ultrapure water (93.0 ± 2.3%) and drinking water (86.9 ± 1.2%) also confirmed the applicability of the method.Article Citation - WoS: 36Citation - Scopus: 35Sorption of As(v) From Waters Using Chitosan and Chitosan-Immobilized Sodium Silicate Prior To Atomic Spectrometric Determination(Elsevier Ltd., 2010) Boyacı, Ezel; Eroğlu, Ahmet Emin; Shahwan, TalalA natural biosorbent containing amine functional groups, chitosan, and a novel sorbent, chitosan-immobilized sodium silicate, were prepared and utilized for the selective sorption of As(V) from waters prior to its determination by atomic spectrometric techniques, namely, hydride generation atomic absorption spectrometry (HGAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Chitosan was synthesized from chitin and sodium silicate was used as the immobilization matrix due to its straightforward synthesis. Through sequential sorption studies, it was shown that chitosan-immobilized sodium silicate has exhibited a better chemical stability than the chitosan itself which demonstrates the advantage of immobilization method. Both chitosan and chitosan-immobilized sodium silicate were shown to selectively adsorb As(V), arsenate, from waters at pH 3.0 at which neither chitin nor sodium silicate displayed any sorption towards As(V). The sorption of arsenate by chitosan is supposed to have electrostatic nature since pH of 3.0 is both the point at which the amino groups in chitosan are protonated and also the predominant form of As(V) is H2AsO4−. A pre-oxidation step is required if both As(III) and As(V) are to be determined. Desorption from the sorbents was realized with 1.0% (w/v) l-cysteine prepared in a pH 3.0 solution adjusted with HCl. Among the possible interfering species tested, only Te(IV) and Sb(III) were shown to cause a decrease in the sorption capacity especially at high interferant concentrations. High concentrations of Sb(III) also resulted in gas phase interference during hydride generation.