Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
19 results
Search Results
Now showing 1 - 10 of 19
Article Citation - WoS: 13Citation - Scopus: 14The Quasi-Static Crush Response of Electron-Beam Ti6al4v Body-Centred Lattices: The Effect of the Number of Cells, Strut Diameter and Face Sheet(Wiley, 2022) Güden, Mustafa; Alpkaya, Alican Tuncay; Arslan Hamat, Burcu; Hızlı, Burak; Taşdemirci, Alper; Tanrıkulu, A. Alptuğ; Yavaş, HakanThe effect of the number of cells, strut diameter and face sheet on the compression of electron-beam-melt (EBM) Ti6Al4V (Ti64) body-centred-cubic (BCC) lattices was investigated experimentally and numerically. The lattices with the same relative density (~0.182) were fabricated with and without 2-mm-thick face sheets in 10 and 5 mm cell size, 8–125 unit cell (two to five cells/edge) and 2 and 1 mm strut diameter. The experimental compression tests were further numerically simulated in the LS-DYNA. Experimentally two bending-dominated crushing modes, namely, lateral and diagonal layer crushing, were determined. The numerical models however exhibited merely a bending-dominated lateral layer crushing mode when the erosion strain was 0.4 and without face-sheet models showed a diagonal layer crushing mode when the erosion strain was 0.3. Lower erosion strains promoted a diagonal layer crushing mode by introducing geometrical inhomogeneity to the lattice, leading to strain localisation as similar to the face sheets which introduced extensive strut bending in the layers adjacent to the face sheets. The face-sheet model showed a higher but decreasing collapse strength at an increasing number of cells, just as opposite to the without face-sheet model, and the collapse strength of both models converged when the number of cells was higher than five-cell/edge. The decrease/increase of the collapse strengths of lattices before the critical number of cells was claimed mainly due to the size-imposed lattice boundary condition, rather than the specimen volume. The difference in the experimental collapse strengths between the 5- and the 10-mm cell-size lattices was ascribed to the variations in the microstructures—hence the material model parameters between the small-diameter and the large-diameter EBM-Ti64 strut lattices.Article Citation - WoS: 3Citation - Scopus: 4Impact Loading and Modelling a Multilayer Aluminium Corrugated/Fin Core: the Effect of the Insertion of Imperfect Fin Layers(John Wiley and Sons Inc., 2019) Sarıkaya, Mustafa; Taşdemirci, Alper; Güden, MustafaThe quasi-static compression (0.0048 m/s) and Taylor-like impact (135, 150, and 200 m/s) loading of a multilayer 1050 H14 aluminium corrugated core were investigated both experimentally and numerically in LS-DYNA using the perfect and imperfect sample models. In the imperfect sample models, one or two layers of corrugated fin structure were replaced by the fin layers made of bent-type cell walls. The localised deformation in the quasi-static imperfect models of cylindrical sample started at the imperfect layers, the same as the tests, and the layers were compressed until about the densification strain in a step-wise fashion. The localised deformation in the perfect models, however, started at the layers at and near the top and bottom of the test sample. In the shock mode, the sample crushed sequentially starting at the impact end layer regardless the perfect or imperfect sample models were used. Furthermore, the perfect and imperfect models resulted in nearly the same initial crushing stresses in the shock mode. The layer strain histories revealed a velocity-dependent layer densification strain. Both model types, the imperfect and perfect, well approximated the stress-time histories and layer deformations of the shock mode. The rigid perfectly plastic locking model based on the numerically determined densification strains also showed well agreements with the experimental and numerical plateau stresses of the shock mode.Article Citation - WoS: 29Citation - Scopus: 32Antimicrobial Activity of Tio2-Coated Orthodontic Ceramic Brackets Against Streptococcus Mutans and Candida Albicans(Springer Verlag, 2010) Özyıldız, Figen; Güden, Mustafa; Uzel, Ataç; Karaboz, İsmail; Akil, Övünç; Bulut, H.Polycrystalline alumina ceramic orthodontic brackets were coated with anatase TiO2 film via a sol-gel dip-coating method. The surface structure morphology and composition of the films were evaluated via scanning electron microscopy, atomic force microscopy, and X-ray diffraction. The antimicrobial activity of the ceramic brackets was assessed against two oral pathogens, S. mutans and C. albicans. The results demonstrated that TiO 2-coated brackets exposed to low energy UV-A illumination efficiently reduced the populations of test microorganisms relative to the uncoated brackets. The reduction efficiencies were 98% for S. mutans ATCC 10449 and 93% for C. albicans ATCC 60193. © The Korean Society for Biotechnology and Bioengineering and Springer 2010.Article Citation - WoS: 41Citation - Scopus: 38Simulation of the Strain Rate Sensitive Flow Behavior of Sic-Particulate Reinforced Aluminum Metal Matrix Composites(Elsevier Ltd., 2008) Tirtom, İsmail; Güden, Mustafa; Yıldız, HasanStrain rate dependent compression mechanical behavior of an SiC-particulate reinforced Al (2024-O) metal matrix composite (MMC) with different particle volume fractions was numerically investigated at various strain rates. Calculations were performed using axisymmetric finite element unit cell model, in which an elastic SiC particle was embedded inside a strain rate sensitive viscoplastic Al matrix. Stress–strain curves of Al matrix material were derived from Split Hopkinson Pressure Bar experiments at various strain rates and used as inputs in the FEM model. Numerically computed stress–strain curves and strain rate sensitivity were compared with those of experiments for a 15% SiC-particulate reinforced MMC. Computed strain rate sensitivity of the MMC was found to be higher than that of the matrix alloy and increased with increasing strain contrary to the strain independent matrix strain rate sensitivity. The strain rate sensitivity of the MMC was also found to increase with increasing particle volume fraction at the same particle size. Finally, several possible reasons including assumptions used in the model, adiabatic heating, microstructural variations between the composite matrix and matrix alloy, particle shape and distribution and damage accumulation for the small discrepancy found between computed and experimental stress–strain curves and strain rate sensitivity of the composite were discussed.Article Citation - WoS: 54Citation - Scopus: 62Sic-Particulate Aluminum Composite Foams Produced by Powder Compacts: Foaming and Compression Behavior(Springer Verlag, 2003) Elbir, Semih; Yılmaz, Selahattin; Toksoy, Ahmet Kaan; Güden, Mustafa; Hall, Ian W.The foaming behavior of SiC-particulate (8.6% by volume) aluminum composite powder compacts contained Titanium Hydride blowing agent was investigated by heating above the melting temperature (750°C) in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiC-particulate addition on foaming and compression behavior. The linear expansions of the compacts at various furnace holding times were ex situ determined. Optical and scanning electron microscopy techniques were used to characterize prepared and deformed foams microstructures. The SiC-particulate addition was found to increase the linear expansion and reduce the extent of the liquid metal drainage and cell coarsening of the aluminum compacts. The composite foam samples also showed higher compressive stresses, but a more brittle behavior as compared with aluminum foams.Article Citation - WoS: 55Citation - Scopus: 61Sic-Particulate Aluminum Composite Foams Produced From Powder Compacts: Foaming and Compression Behavior(Springer Verlag, 2006) Güden, Mustafa; Yüksel, SinanThe foaming behavior of SiC-particulate (SiCp) aluminum composite powder compacts containing titanium hydride blowing agent was investigated by heating to 750°C in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiCp-addition on the foaming and compression behavior. The SiCp-addition (10 wt%) was found to increase the linear expansion of the Al powder compacts presumably by increasing the surface as well as the bulk viscosities. The compression tests conducted on Al and 10 and 20% SiCp foams further showed a more brittle compression behavior of SiCp/Al foams as compared with Al foams. The collapse stresses of Al and 10% SiCp/Al foams were also predicted using the equations developed for the open and closed cell foams. Predictions have shown that Al foam samples behaved similar to open cell foams, while 10% SiCp/Al foam collapse stress values were found between those of open and closed cell foams, biasing towards those of the open cell foams.Article Citation - WoS: 21Citation - Scopus: 25Quasi-Static and Dynamic Crushing of Empty and Foam-Filled Tubes(Springer Verlag, 2001) Hall, Ian W.; Ebil, Özgenç; Güden, Mustafa; Yu, C.-J.Metallic foam-filled tubes and their empty counterparts have been tested at quasi-static and dynamic strain rates in order to determine their energy absorption capabilities. Data from the Split-Hopkinson Pressure Bar have been used to generate force vs. displacement curves that are somewhat analogous to pseudo-engineering stress-strain curves. Force balance calculations have also been made. These results indicate that, on an equal weight basis, foam-filled tubes offer greater energy absorption capability than empty tubes at quasi-static strain rates. However, the benefit of foam filling does not appear to be extended to strain rates of the order of 200–500 s−1. Force balance calculations are shown to have potential as a method for monitoring the crushing of metallic foams at high strain rate.Article Citation - WoS: 11Citation - Scopus: 14Quasi-Static and Dynamic Compression Behaviour of an Fptm Alumina-Reinforced Aluminium Metal Matrix Composite(Springer Verlag, 1998) Güden, Mustafa; Hall, Ian W.An aluminium metal matrix composite reinforced with continuous unidirectional α-alumina fibres has been compression tested at quasi-static and dynamic strain rates. In the transverse direction, the composite showed increasing flow stress (at 5% strain) and maximum stress within the studied strain rates, 10−3−3 × 103 s−1. In the longitudinal direction, the maximum stress of the composite increased similarly with increasing strain rates within the range 10−5−7 × 102 s−1. It is shown that, if brooming of the sample ends can be suppressed, the failure stress of the composite in longitudinal compression increases significantly. Metallographic observations reveal the typical modes of damage initiation in the composite.Article Citation - WoS: 30Citation - Scopus: 33Processing and Compression Testing of Ti6al4v Foams for Biomedical Applications(Springer Verlag, 2009) Dizlek, Mustafa Eren; Güden, Mustafa; Türkan, Uğur; Taşdemirci, AlperOpen cell Ti6Al4V foams (60% porosity) were prepared at sintering temperatures between 1,200 and 1,350 °C using ammonium bicarbonate particles (315–500 μm) as space holder. The resulting cellular structure of the foams showed bimodal pore size distribution, comprising macropores (300–500 μm) and micropores (1–30 μm). Compression tests have shown that increasing sintering temperature increased the elastic modulus, yield and compressive strength, and failure strain of foams. The improvements in the mechanical properties of foams prepared using smaller size Ti64 powder with bimodal particle distribution were attributed to the increased number of sintering necks and contact areas between the particles. Finally, the strength of foams sintered at 1,350 °C was found to satisfy the strength requirement for cancellous bone replacement.Article Citation - WoS: 27Citation - Scopus: 30Single- and Double-Layer Aluminum Corrugated Core Sandwiches Under Quasi-Static and Dynamic Loadings(SAGE Publications Inc., 2016) Kılıçaslan, Cenk; Odacı, İsmet Kutlay; Güden, MustafaThe crushing of single- and double-layer zig-zag trapezoidal corrugated core sandwiches was investigated experimentally and numerically at quasi-static and dynamic rates. The buckling stress of sandwiches increased when the rate increased from quasi-static to dynamic. The increased buckling stresses were ascribed to the micro-inertial effects, which altered the buckling mode of the core from three plastic hinges to higher number of plastic hinge formations. The initial buckling stress was numerically shown to be imperfection sensitive when the imperfection size was comparable with the buckling length. The numerical buckling stresses of zig-zag and straight corrugated cores were similar, while higher inertial effects were found in triangular corrugated core.