Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
52 results
Search Results
Now showing 1 - 10 of 52
Correction Citation - WoS: 1Erratum: Bioactive Snail Mucus-Slime Extract Loaded Chitosan Scaffolds for Hard Tissue Regeneration: the Effect of Mucoadhesive and Antibacterial Extracts on Physical Characteristics and Bioactivity of Chitosan Matrix (Biomedical Materials (Bristol) (2021) 16 (065008) Doi: 10.1088/1748-605x(IOP Publishing, 2023) Perpelek, M.; Tamburaci, S.; Aydemi̇r, S.; Tıhmınlıoğlu, F.; Baykara, B.; Karakaşli, A.; Havitçioǧlu, H.The authors regret that some errors were identified in 'figures 12 and 13' on pages 14 and 15, in the published manuscript concerning fluorescence microscopy images of Saos-2 and SW1353 cells on scaffolds for 1 and 3 d of incubation. The fluorescence images in figures 12 and 13 were mistakenly used as duplicated due to the inadvertently mislabeling during the processing of files and integrating them into the final figures. Intensity data regarding corrected fluorescence images were also measured and corrected. The revised figures (figures 12 and 13) and their captions appear below. The authors apologize for this error and state that this does not change the scientific conclusions of the article in any way. (Figure Presented). © 2023 IOP Publishing Ltd.Erratum Citation - WoS: 1Corrigendum: Bioactive Snail Mucus-Slime Extract Loaded Chitosan Scaffolds for Hard Tissue Regeneration: The Effect of Mucoadhesive and Antibacterial Extracts on Physical Characteristics and Bioactivity of Chitosan Matrix (2021biomed. Mater.16 065008)(NLM (Medline), 2023) Perpelek, M.; Tamburaci, S.; Aydemir, S.; Tıhmınlıoğlu, F.; Baykara, B.; Karakaşli, A.; Havitçioǧlu, H.Article Citation - WoS: 11Fabrication of Helix Aspersa Extract Loaded Gradient Scaffold With an Integrated Architecture for Osteochondral Tissue Regeneration: Morphology, Structure, and in Vitro Bioactivity [2](American Chemical Society, 2023) Tamburacı, Sedef; Perpelek, Merve; Aydemir, Selma; Baykara, Başak; Havıtçıoğlu, Hasan; Tıhmınlıoğlu, FundaRegeneration of osteochondral tissue with its layered complex structure and limited self-repair capacity has come into prominence as an application area for biomaterial design. Thus, literature studies have aimed to design multilayered scaffolds using natural polymers to mimic its unique structure. In this study, fabricated scaffolds are composed of transition layers both chemically and morphologically to mimic the gradient structure of osteochondral tissue. The aim of this study is to produce gradient chitosan (CHI) scaffolds with bioactive snail (Helix aspersa) mucus (M) and slime (S) extract and investigate the structures regarding their physicochemical, mechanical, and morphological characteristics as well as in vitro cytocompatibility and bioactivity. Gradient scaffolds (CHI-M and CHI-S) were fabricated via a layer-by-layer freezing and lyophilization technique. Highly porous and continuous 3D structures were obtained and observed with SEM analysis. In addition, scaffolds were physically characterized with water uptake test, micro-CT, mechanical analysis (compression tests), and XRD analysis. In vitro bioactivity of scaffolds was investigated by co-culturing Saos-2 and SW1353 cells on each compartment of gradient scaffolds. Osteogenic activity of Saos-2 cells on extract loaded gradient scaffolds was investigated in terms of ALP secretion, osteocalcin (OC) production, and biomineralization. Chondrogenic bioactivity of SW1353 cells was investigated regarding COMP and GAG production and observed with Alcian Blue staining. Both mucus and slime incorporation in the chitosan matrix increased the osteogenic differentiation of Saos-2 and SW1353 cells in comparison to the pristine matrix. In addition, histological and immunohistological staining was performed to investigate ECM formation on gradient scaffolds. Both characterization and in vitro bioactivity results indicated that CHI-M and CHI-S scaffolds show potential for osteochondral tissue regeneration, mimicking the structure as well as enhancing physical characteristics and bioactivity. © 2023 The Authors. Published by American Chemical Society.Article Citation - WoS: 23Citation - Scopus: 26Fish scale containing alginate dialdehyde-gelatin bioink for bone tissue engineering(IOP Publishing Ltd, 2023) Özenler, Aylin Kara; Distler, Thomas; Tıhmınlıoğlu, Funda; Boccaccini, Aldo RThe development of biomaterial inks suitable for biofabrication and mimicking the physicochemical properties of the extracellular matrix is essential for the application of bioprinting technology in tissue engineering (TE). The use of animal-derived proteinous materials, such as jellyfish collagen, or fish scale (FS) gelatin (GEL), has become an important pillar in biomaterial ink design to increase the bioactivity of hydrogels. However, besides the extraction of proteinous structures, the use of structurally intact FS as an additive could increase biocompatibility and bioactivity of hydrogels due to its organic (collagen) and inorganic (hydroxyapatite) contents, while simultaneously enhancing mechanical strength in three-dimensional (3D) printing applications. To test this hypothesis, we present here a composite biomaterial ink composed of FS and alginate dialdehyde (ADA)-GEL for 3D bioprinting applications. We fabricate 3D cell-laden hydrogels using mouse pre-osteoblast MC3T3-E1 cells. We evaluate the physicochemical and mechanical properties of FS incorporated ADA-GEL biomaterial inks as well as the bioactivity and cytocompatibility of cell-laden hydrogels. Due to the distinctive collagen orientation of the FS, the compressive strength of the hydrogels significantly increased with increasing FS particle content. Addition of FS also provided a tool to tune hydrogel stiffness. FS particles were homogeneously incorporated into the hydrogels. Particle-matrix integration was confirmed via scanning electron microscopy. FS incorporation in the ADA-GEL matrix increased the osteogenic differentiation of MC3T3-E1 cells in comparison to pristine ADA-GEL, as FS incorporation led to increased ALP activity and osteocalcin secretion of MC3T3-E1 cells. Due to the significantly increased stiffness and supported osteoinductivity of the hydrogels, FS structure as a natural collagen and hydroxyapatite source contributed to the biomaterial ink properties for bone engineering applications. Our findings indicate that ADA-GEL/FS represents a new biomaterial ink formulation with great potential for 3D bioprinting, and FS is confirmed as a promising additive for bone TE applications.Article Citation - WoS: 51Citation - Scopus: 583d Printed Gelatin/Decellularized Bone Composite Scaffolds for Bone Tissue Engineering: Fabrication, Characterization and Cytocompatibility Study(Elsevier, 2022) Kara, Aylin; Distler, Thomas; Polley, Christian; Schneidereit, Dominik; Seitz, Hermann; Friedrich, Oliver; Tıhmınlıoğlu, Funda; Boccaccini, Aldo RThree-dimensional (3D) printing technology enables the design of personalized scaffolds with tunable pore size and composition. Combining decellularization and 3D printing techniques provides the opportunity to fabricate scaffolds with high potential to mimic native tissue. The aim of this study is to produce novel decellularized bone extracellular matrix (dbECM)-reinforced composite-scaffold that can be used as a biomaterial for bone tissue engineering. Decellularized bone particles (dbPTs, ∼100 μm diameter) were obtained from rabbit femur and used as a reinforcement agent by mixing with gelatin (GEL) in different concentrations. 3D scaffolds were fabricated by using an extrusion-based bioprinter and crosslinking with microbial transglutaminase (mTG) enzyme, followed by freeze-drying to obtain porous structures. Fabricated 3D scaffolds were characterized morphologically, mechanically, and chemically. Furthermore, MC3T3-E1 mouse pre-osteoblast cells were seeded on the dbPTs reinforced GEL scaffolds (GEL/dbPTs) and cultured for 21 days to assess cytocompatibility and cell attachment. We demonstrate the 3D-printability of dbPTs-reinforced GEL hydrogels and the achievement of homogenous distribution of the dbPTs in the whole scaffold structure, as well as bioactivity and cytocompatibility of GEL/dbPTs scaffolds. It was shown that Young's modulus and degradation rate of scaffolds were enhanced with increasing dbPTs content. Multiphoton microscopy imaging displayed the interaction of cells with dbPTs, indicating attachment and proliferation of cells around the particles as well as into the GEL-particle hydrogels. Our results demonstrate that GEL/dbPTs hydrogel formulations have potential for bone tissue engineering.Article Citation - WoS: 8Citation - Scopus: 9Polymeric Thermal Analysis of C+h and C+h+ar Ion Implanted Uhmwpe Samples(Elsevier Ltd., 2007) Kaya, N.; Öztarhan, Ahmet M.; Urkaç, Emel Sokullu; Ila, D.; Budak, S.; Oks, E.; Tıhmınlıoğlu, Funda; Muntele, C.Chemical surface characterization of C + H hybrid ion implanted UHMWPE samples were carried out using DSC (differential scanning calorimeter) and TGA (thermal gravimetric analysis) techniques. Samples were implanted with a fluence of 10(17) ion/cm(2) and an extraction voltage of 30 kV. The study of TGA and DSC curves showed that: (1) Polymeric decomposition temperature increased, (2) T-m, Delta C-p and Delta H-m values changed while Delta C-p and Delta H-m increased. T-g value could not be measured, because of some experimental limitations. However, the increase in Delta H-m values showed that T-g values increased, (3) the branch density which indicated the increase in number of cross-link (M-c) decreased in ion implanted samples and (4) increase in Delta H-m values indicated increase in crystallinity of implanted surface of UHMWPE samples.Conference Object Structural and Thermal Characterization of Ti+o Ion Implanted Ultrahigh Molecular Weight Polyethylene (uhmwpe)(American Institute of Physics, 2009) Öztarhan, Ahmet; Urkaç Sokullu, Şadiye Emel; Tıhmınlıoğlu, Funda; Kaya, N.; Ila, Daryush; Budak, S.; Nikolaev, A.In this work, Metal-Gas Hybrid Ion Implantation technique was used as a tool for the surface modification of Ultra High Molecular Weight Polyethylene (UHMWPE). Samples were Ti + O ion implanted by using Metal-Vapour Vacuum Arc (MEVVA) ion implanter to a fluence of 5x10(16) ion/cm(2) for each species and extraction voltage of 30 kV. Untreated and surface treated samples were investigated by Rutherford Back Scattering (RBS) Spectrometry, Attenuated Total Reflectance - Fourier Transform Infrared (ATR-FTIR) Spectroscopy, Thermo Gravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC). Results indicate that Ti + O ion implantation can be applied on UHMWPE surfaces successfully. ATR-FTIR spectra indicate that the C-H concentration on the surface decreased after Ti + O implantation. Thermal characterization with TGA and DSC shows that polymeric decomposition temperature is shifted after ion implantation.Conference Object Citation - Scopus: 4Trans-resveratrol’ün Kitosan Mikroküreler İçerisindeki Kararlılığı(Institute of Electrical and Electronics Engineers Inc., 2009) Altıok, Duygu; Altıok, Evren; Bayraktar, Oğuz; Tıhmınlıoğlu, Fundatrans-Resveratrol, (3,5,4?-trihydroxy-trans-stilbene), a phenolic compound present in some plant species, have been shown to posses antioxidative, anticarcinogenic and antitumour properties. However, under UV light, it turns into -cis form and looses its bioactivity.This study aims to increase the stability of trans-resveratrol by loading it into chitosan microspheres. Within this context, the trans-resveratrol loaded chitosan microspheres was produced by spray drying and then the resultant microspheres were characterized. The particle size and the surface morphology of resultant microspheres were investigated by scanning electron microscope (SEM) and the thermal properties were determined by thermogravimetry analyser(TGA). The stability of free and that of inside the microspheres was determined by high performance liquid chromatography (HPLC). It was found that the stability of trans-resveratrol incorporated into chitosan microspheres kept constant. ©2009 IEEE.Article Citation - WoS: 5Citation - Scopus: 7Effect of the Zeolite Filler on the Thermal Degradation Kinetics of Polypropylene(Scibulcom Ltd., 2006) Tıhmınlıoğlu, Funda; Pehlivan, Hilal; Balköse, Devrim; Ülkü, SemraIn this study, the thermal degradation behaviour of polypropylene (PP) and polypropylene-zeolite composites was investigated. Clinoptilolite, a natural zeolitic tuff, was used as the filling material into the composites. Effect of both pure clinoptilolite and silver ion exchanged form of clinoptilolite addition on the thermal degradation kinetics of polypropylene composites was studied by using differential scanning calorimetry (DSC) and thermal gravimetry analysis (TGA) techniques. Polymer degradation was evaluated by using DSC with heating rates of 5, 10, and 20 degrees C/ min from room temperature up to 500 degrees C. Silver concentration (4.36, 27.85 and 183.8 mg Ag/g zeolite) was the selected parameter under consideration. From the DSC curves, it was observed that the heat of degradation values of the composites containing 2-6% silver exchanged zeolites (321-390 kJ/kg) were larger compared to that of the pure PP free of silver and zeolite (258 kJ/kg). From the DSC results it was confirmed that PP-zeolite composites can be used at higher temperatures compared to the pure PP polymer because of its higher thermal stability. The thermal decomposition activation energies of the composites were calculated by using both the Kissenger and Ozawa models. The values predicted from these two equations were in close agreement. From the TGA curves, it was found that zeolite addition into the PP matrix speeds down the decomposition reaction, however, silver exchanged zeolite addition into the matrix accelerates the reaction. The higher the silver concentration, the lower the thermal decomposition activation energies were obtained. As a result, PP was found to be much more susceptible to thermal decomposition in the presence of silver exchanged zeolite.Article Citation - WoS: 54Citation - Scopus: 64Bioactive Fish Scale Incorporated Chitosan Biocomposite Scaffolds for Bone Tissue Engineering(Elsevier Ltd., 2019) Kara, Aylin; Tamburacı, Sedef; Tıhmınlıoğlu, Funda; Havıtçıoğlu, HasanRecently, biologically active natural macromolecules have come into prominence to be used as potential materials in scaffold design due to their unique characteristics which can mimic the human tissue structure with their physical and chemical similarity. Among them, fish scale (FS) is a biologically active material with its structural similarity to bone tissue due to including type I collagen and hydroxyapatite and also have distinctive collagen arrangement. In the present study, it is aimed to design a novel composite scaffold with FS incorporation into chitosan (CH) matrix for bone tissue regeneration. Therefore, two biological macromolecules, fish scale and chitosan, were combined to produce bio-composite scaffold. First, FS were decellularized with the chemical method and disrupted physically as microparticles (100 in), followed by dispersal in CH with ultrasonic homogenisation, CH/FS scaffolds were fabricated by lyophilization technique. Scaffolds were characterized physically, chemically, mechanically, and morphologically. SEM and porosity results showed that CH/FS scaffolds have uniform pore structure showing high porosity. Mechanical properties and degradation rate are enhanced with increasing FS content. In vitro cytotoxicity, proliferation and osteogenic activity of the scaffolds were evaluated with SaOS-2 cell line. CH/FS scaffolds did not show any cytotoxicity effect and the cells were gradually proliferated during culture period. Cell viability results showed that, FS microparticles had a proliferative effect on SaOS-2 cells when compared to control group. ALP activity and biomineralization studies indicated that FS micro particle reinforcement increased osteogenic activity during culture period. As a biological macromolecule with unique characteristics, FS was found as cytocompatible and provided promising effects as reinforcement agents for polymeric scaffolds. In conclusion, fabricated CH/FS bio-composites showed potential for bone tissue engineering applications. (C) 2019 Elsevier B.V. All rights reserved.