Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
5 results
Search Results
Now showing 1 - 5 of 5
Article Citation - WoS: 5Citation - Scopus: 5Effect of the Synthesis Conditions on the Properties of Co Embedded Porous Si Nanostructures(Elsevier Ltd., 2019) Çetinel, Alper; Artunç, Nurcan; Tarhan, EnverThe electrodeposition of cobalt in the porous silicon (PSi) substrate was investigated in terms of the deposition times and current densities. The PSi/Co samples were characterized by SEM, XRD, Raman, and photoluminescence (PL) spectroscopies. The results indicated that for all current densities, the PL intensities of PSi/Co samples with shorter deposition times (t(s) <= 20 min) increased due to spherical Co nanoparticles (NPs) could be created the new recombination centers, compared to that of the undeposited PSi. On the other hand, the PL intensity of PSi/Co samples significantly decreased at longer deposition times (t(1) > 20 min) because of larger Co NP cluster promoted the formation of non-radiative centers. The increased PL intensities in samples with t(s) were attributed to both the quantum confinement effect and surface effects. PL analyses also suggested that after exposure to air for 60 days, PL characteristics of PSi/Co were stabilized depending on deposition time and current density.Article Citation - WoS: 9Citation - Scopus: 7Epitaxial Characteristics of Mbe-Grown Znte Thin Films on Gaas (211)b Substrates(Springer, 2019) Özçeri, Elif; Tarhan, EnverHighly crystalline ZnTe thin films were grown on GaAs (211)B substrates by molecular beam epitaxy (MBE) for potential applications such as MCT detectors and optoelectronic devices. We investigated the effects of Te to Zn (VI/II) flux ratio on the quality of ZnTe films in terms of crystal orientation, elemental composition, surface roughness, and dislocation density. Atomic concentrations of Zn, Te, and oxygen complexes due to oxygen contamination on the film surfaces were analyzed by X-ray photoelectron spectroscopy. X-ray double crystal rocking curve full width half maximum (FWHM) of ZnTe (422) peak was observed as 233 arcseconds for a 1.66 mu m thick film, which indicates high crystallinity. Wet chemical etching was applied to the films to quantify the crystal quality by calculating etch pit densities (EPD) from scanning electron microscope images. A very low EPD value of 1.7 x 10(7) cm(-2) was measured. Additionally, the root mean square roughness values, obtained from atomic force microscopy topography images were in the range of 10-25 nm. These values were supported by FWHM values of red green blue color intensity histograms obtained from Nomarski Microscope images. The results of our analyses indicate that the VI/II flux ratios of 4 and 4.5 produce the best quality ZnTe films on GaAs (211)B substrates.Article Citation - WoS: 6Citation - Scopus: 10Effect of Annealing on the Density of Defects in Epitaxial Cdte (211)/Gaas(Springer, 2018) Bakali, Emine; Selamet, Yusuf; Tarhan, EnverCdTe thin films were grown on GaAs (211) wafers by molecular beam epitaxy as the buffer layer for HgCdTe infrared detector applications. We studied the effect of annealing on the density of dislocation of these CdTe thin films under varying annealing parameters such as annealing temperature, annealing duration, and number of cycles. Annealings were carried out using a homemade annealing reactor possessing a special heater element made of a Si wafer for rapid heating. The density of dislocations, which were made observable with a scanning electron microscope after etching with an Everson solution, were calculated by counting the number of dislocations per unit surface area, hence the term etch pit density (EPD). We were able to decrease EPD values by one order of magnitude after annealing. For example, the best EPD value after a 20-min annealing at 400°C was ∼ 2 × 107 cm−2 for a 1.63-μm CdTe thin film which was about 9.5 × 107 cm−2 before annealing. We also employed Raman scattering measurements to see the changes in the structural quality of the samples. From the Raman measurements, we were able to see improvements in the quality of our samples from the annealing by studying the ratio of 2LO/LO phonon mode Raman intensities. We also observed a clear decrease in the intensity of Te precipitations-related modes, indicating a decrease in the size and number of these precipitations.Article Citation - WoS: 35Citation - Scopus: 38Influence of Sulfurization Temperature on Cu2znsns4 Absorber Layer on Flexible Titanium Substrates for Thin Film Solar Cells(IOP Publishing Ltd., 2018) Buldu, Dilara Gökçen; Cantaş, Ayten; Türkoğlu, Fulya; Akça, Fatime Gülşah; Meriç, Ece; Özdemir, Mehtap; Tarhan, Enver; Özyüzer, Lütfi; Aygün, GülnurIn this study, the effect of sulfurization temperature on the morphology, composition and structure of Cu2ZnSnS4 (CZTS) thin films grown on titanium (Ti) substrates has been investigated. Since Ti foils are flexible, they were preferred as a substrate. As a result of their flexibility, they allow large area manufacturing and roll-to-roll processes. To understand the effects of sulfurization temperature on the CZTS formation on Ti foils, CZTS films fabricated with various sulfurization temperatures were investigated with several analyses including x-ray diffraction (XRD), scanning electron microscopy (SEM), x-ray photoelectron spectroscopy and Raman scattering. XRD measurements showed a sharp and intense peak coming from the (112) planes of the kesterite type lattice structure (KS), which is strong evidence for good crystallinity. The surface morphologies of our thin films were investigated using SEM. Electron dispersive spectroscopy was also used for the compositional analysis of the thin films. According to these analysis, it is observed that Ti foils were suitable as substrates for the growth of CZTS thin films with desired properties and the sulfurization temperature plays a crucial role for producing good quality CZTS thin films on Ti foil substrates.Article Citation - WoS: 42Citation - Scopus: 46Importance of Cds Buffer Layer Thickness on Cu2znsns4-Based Solar Cell Efficiency(IOP Publishing Ltd., 2018) Cantaş, Ayten; Türkoğlu, Fulya; Meriç, Ece; Akça, Fatime Gülşah; Özdemir, Mehtap; Tarhan, Enver; Özyüzer, Lütfi; Özyüzer, Gülnur AygünCu2ZnSnS4 (CZTS) thin films were grown on Mo-coated soda lime glass (SLG) substrates by the sulfurization of DC magnetron-sputtered Zn, Sn and Cu metallic precursors under a sulfur atmosphere at 550 °C for 45 min. Understanding the composition and structure of the CZTS absorber layer is necessary to obtain efficient solar cells. With this aim, x-ray diffractometry, Raman spectroscopy, scanning electron microscopy, energy dispersive spectroscopy and x-ray photoelectron spectroscopy were used to investigate the CZTS absorber layers. CZTS absorber films were obtained and found to be Cu-poor and Zn-rich in composition, which are both qualities desired for efficient solar cells. CdS was used as a buffer layer and was grown by the chemical bath deposition technique. The optical properties of CdS films on SLG were searched for using a spectroscopic ellipsometer and the results revealed that the bandgap increases with film thickness increment. CZTS-based solar cells with different CdS buffer layer thicknesses were prepared using a SLG/Mo/CZTS/CdS/ZnO/AZO solar cell configuration. The influence of the CdS buffer layer thickness on the performance of the CZTS solar cells was investigated. Device analysis showed that electrical characteristics of solar cells strongly depend on the buffer layer's thickness. Highly pronounced changes in V OC, fill factor and J SC parameters, which are the main efficiency limiting factors, with changing buffer layer thicknesses were observed. Our experiments confirmed that decreasing the CdS thickness improved the efficiency of CZTS solar cells down to the lowest thickness limit.