Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
17 results
Search Results
Now showing 1 - 10 of 17
Article Citation - WoS: 2Citation - Scopus: 2Sintering Under High Heating Rates(Annual Reviews, 2025) Karacasulu, Levent; Maniere, Charles; Vakifahmetoglu, Cekdar; Marinel, Sylvain; Biesuz, MattiaRapid sintering using a high heating rate is growing in technological and scientific interest. This is motivated by the promise of reducing the carbon footprint of sintering and developing materials with properties and microstructures different from those achievable by conventional heating. For instance, rapid heating can induce suppression of grain growth, the possibility of obtaining modified space charges and elemental segregations, and the development of out-of-equilibrium materials. Severe challenges still exist for the industrial exploitation of rapid sintering technologies, and, nowadays, only fast firing can be considered mature. Most of these limitations are related to the homogeneity of the sample and the possibility of obtaining complex shapes. This review investigates developments in rapid sintering by comparing different processes, suggested mechanisms, and future challenges.Article Citation - WoS: 1Citation - Scopus: 1Fast Firing Technique for Martian Regolith Simulant: Advancing Isru Capabilities(Academic Press inc Elsevier Science, 2025) Karacasulu, Levent; Tomasini, Alessandro; Vakifahmetoglu, Cekdar; Biesuz, MattiaIn-Situ Resource Utilization (ISRU) approaches hold significant importance in plans for space colonization. This work explores a different ISRU concept applying fast-firing, a robust and well-known industrial process, to Mars regolith simulant (MGS-1). The fast-fired specimens were compared to the ones obtained by conventional sintered under low heating rates. When the holding time at the firing temperature is longer than 15 min, fast-fired specimens exhibited higher density and flexural strength (> 35 MPa) than conventional sintering. For both processes, the bulk density values and the mechanical properties of the regolith compacts were enhanced with increasing dwell time. This was attributed to higher heating rates changing the densification/crystallization kinetics involving the basalt glass in the regolith composition. Specifically, high heating rate promotes sintering over crystallization. On these bases, fast firing can be considered a potential candidate for ISRU on Mars.Article Citation - WoS: 5Citation - Scopus: 5Ultrafast High-Temperature Sintering of Yttria-Stabilized Zirconia in Reactive N<sub>2</Sub> Atmosphere(Elsevier Sci Ltd, 2025) Karacasulu, Levent; de Beauvoir, Thomas Herisson; De Bona, Emanuele; Cassetta, Michele; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.; Biesuz, MattiaSo far, ultrafast high-temperature sintering (UHS) has always been carried out in an inert environment. In the present work, we investigated UHS of 3YSZ in nitrogen and argon atmosphere showing that "the atmosphere matters". Highly densified samples can be obtained in both environments but densification and grain growth are significantly retarded in N-2. Moreover, the phase evolution is strongly atmosphere-dependent with the samples treated in Ar remaining tetragonal and those treated under N-2 progressively reducing their tetragonality, eventually converting into cubic zirconia and rock salt oxynitride. The results can be explained by the incorporation of nitrogen within the ZrO2 lattice. Electrochemical impedance spectroscopy demonstrates that while the ionic bulk conductivity are marginally influenced by the sintering atmosphere, the grain boundaries' capacitive behavior strongly changes. After UHS under 30 A, excellent ionic conductors were obtained without substantial grain boundary-blocking effects.Article Citation - WoS: 5Citation - Scopus: 8High Entropy (hftizrvnb)b2 Ceramic Particulate Reinforced Al Matrix Composites: Synthesis, Mechanical, Microstructural and Thermal Characterization(Elsevier Ltd, 2024) Süzer,İ.; Özçakıcı,Y.E.; Tekinşen,A.S.; Bayrak,K.G.; Mertdinç-Ülküseven,S.; Balcı-Çağıran,Ö.; Ağaoğulları,D.This study aims to introduce a novel type of particulate reinforced Al matrix composite. High entropy (HfTiZrVNb)B2 ceramic particulate reinforced Al matrix composites were produced via a combined process of different powder metallurgy methods. Firstly, boride compounds (HfB2, TiB2, ZrB2, VB2, NbB2) were synthesized in the laboratory scale using the related metal oxide, boron oxide, and magnesium by mechanochemical synthesis (MCS) and leaching processes under optimum conditions. Secondly, the synthesized and purified boride powders were mixed in equimolar ratios using a planetary ball mill for 72 h, and they were sintered at 2000 °C under 30 MPa via spark plasma sintering (SPS). Thirdly, equimolar high entropy (HfTiZrVNb)B2 bulks were crushed, converted into powder forms, and added into Al powders at different amounts as 1, 2, 5, 10, and 15 wt %. Lastly, these powder blends were mechanically alloyed in a vibratory ball mill for 6 h, cold pressed and pressureless sintered at 630 °C for 2 h. For characterization techniques, X-ray diffractometry (XRD), thermal analysis, scanning electron microscopy/energy dispersive spectrometry (SEM/EDS), density measurements using pycnometer and Archimedes' methods, microhardness and dry sliding wear tests were conducted on the sintered composites. The highest hardness (∼1.5 GPa) and the lowest wear rate (∼0.0012 mm3/Nm) were obtained in the Al-15 wt % (HfTiZrVNb)B2 sample. © 2024 Elsevier Ltd and Techna Group S.r.l.Article Citation - WoS: 13Citation - Scopus: 13On the Temperature Measurement During Ultrafast High-Temperature Sintering (uhs): Shall We Trust Metal-Shielded Thermocouples?(Elsevier Sci Ltd, 2024) Biesuz, Mattia; Karacasulu, Levent; Vakifahmetoglu, Cekdar; Sglavo, Vincenzo M.Temperature measurement upon ultrafast high-temperature sintering (UHS) is a crucial task. Herein, we provide some arguments posing concerns about the use of metal-shielded thermocouples as temperature probes in UHS. The discussion is based on literature data and on some ad hoc experiments. In detail, we show at least two cases in the literature where the use of a shielded thermocouple causes a substantial underestimation of the UHS temperature. The argumentation is based on comparing the thermocouples read and the observed phase and microstructural evolution. Moreover, by means of a simple experimental design, we show that a metal shield on the thermocouple tip can substantially reduce the measured temperature. Since the metal shield is orders of magnitude more thermally conductive than the graphite felt used as heating element in UHS, it efficiently removes heat from the thermocouple tip region. As such, data acquired from shielded thermocouples must be treated with care.Article Citation - WoS: 3Citation - Scopus: 3Effects of Different Precursors on the Aging and Electrocaloric Properties of Mn-Doped Ba0.95sr0.05tio3 Ceramics(Springer, 2023) Karakaya, Merve; Erdem, Emre; Akdoğan, Yaşar; Adem, UmutIn this study, the effects of different types of Mn precursors (MnO2 and Mn2O3) and sintering temperature on the defect dipole formation, ferroelectric aging and electrical properties were investigated by using Ba0.95Sr0.05TiO3 ceramics as the base. Both Mn precursors were substituted to the Ti-site as 1 mol% and two different sintering temperatures of 1325 and 1400 degrees C were used to study the effect of grain size. We deduced that slightly higher amounts of Mn2+ can be incorporated into the perovskite structure when MnO2 is used as the precursor, by using X-ray diffraction and electron paramagnetic resonance spectroscopy. Mn-doped samples sintered at 1325 degrees C age faster than those sintered at 1400 degrees C. Aging caused a decrease in the electrocaloric effect whereas Mn-doping increased it. This study shows that Mn precursor used for the acceptor doping affects the amount of Mn incorporated into the structure and therefore electrical properties of the resulting ceramics.Article Citation - WoS: 37Citation - Scopus: 41Processing and Characterization of Geopolymer and Sintered Geopolymer Foams of Waste Glass Powders(Elsevier, 2021) Polat, Dilan; Güden, MustafaGeopolymer foams of fine and coarse waste glass (WG) powders were prepared using an activation solution of NaOH (8 M) and Na2SiO3. The effects of WG powder particle size, solid/liquid ratio (S/L = 1, 1.5, and 2) and Al foaming agent content (2-20 wt%) on the expansion and temperature behavior of the slurries were determined in-situ using a laser sensor and a thermocouple, respectively. The geopolymer foams processed using a coarse WG powder slurry, S/L = 2, and 2 wt% Al, were further sintered at 600, 700, 725, and 750 degrees C. The compression strengths and thermal conductivities of the geopolymer and sintered geopolymer foams were also determined. The slurry expansions continued until about a maximum, and the temperatures of the slurries increased to a maximum, 85-88 degrees C. At the maximum temperature, the slurry evaporation and the resultant increase in the S/L ratio limited the slurry expansion. Increasing the Al content decreased the final density of the foams (238-555 kg m-3), while the coarse powder slurries resulted in lower densities than the fine powder slurries. Three crystal phases, muscovite, sodium aluminum silicate hydrate, and thermonitrite, were determined in the geopolymer foams. The muscovite formation was noted to be favored at high S/L ratios. During sintering, the partial melting of glass particles started after about 700 degrees C, while sintering above this temperature decreased the final density of the foams. The reduced density above 700 degrees C was ascribed to the release of CO2 due to the decomposition of thermonitrite. Both the compressive strength and thermal conductivity of the geopolymer and sintered geopolymer foams increased with increasing foam density. The highest increase in the compressive strength and reduction in the density were seen in the geopolymer foams sintered at 750 degrees C.Article Citation - WoS: 54Citation - Scopus: 58Sintering and Microstructural Investigation of Gamma–alpha Alumina Powders(Elsevier Ltd., 2014) Yalamaç, Emre; Trapani, Antonio; Akkurt, SedatSintering behaviors of commercially available alumina powders were investigated using constant-heating rate dilatometric experiments. Each powder had different proportion of alpha/gamma alumina. Densification behaviors of powders were studied up to 1600 °C with three different heating rates of 1, 3.3 and 6.6 °C/min. Compacts of different gamma content alumina powders exhibited systematic anomalous second peaks in the densification rate curves at certain heating rates and temperatures. At 3.3 °C/min heating rate experiments, densification curves of 10% gamma phase alumina powder compacts reached a plateau after 1450 °C, and did not increase any further at higher temperatures. This phenomenon was double checked to understand powder behavior during sintering. 10% gamma phase alumina powder compacts showed the highest density for each heating rate. It reached 94% theoretical density with 1 °C/min heating rate. But 20% gamma phase alumina powder compacts had the finest grain size of about 1.40 ?m. Final density and porosity of compacts were also tested by image analysis and the results were coherent with Archimedes results. © 2014 Karabuk UniversityArticle Citation - WoS: 103Citation - Scopus: 110Cold Sintering of Ceramics and Glasses: a Review(Elsevier Ltd., 2020) Ahmetoğlu, Çekdar Vakıf; Karacasulu, LeventTraditionally ceramic artifacts are processed at high temperatures (> 1000 degrees C) by classical sintering techniques such as solid state, liquid phase and pressure-assisted sintering. Recently, inspired from the geology, novel sintering approaches that allow the densification of ceramic components at relatively low temperatures <= 400 degrees C have been proposed. While initial efforts for such low temperature densification concept were developed in the mid-70s, the topic has become increasingly prominent in the last decade. Currently, these low temperature methods can be classified into four main groups: (i) hydrothermal reaction sintering (HRS), (ii) hydrothermal hot pressing (HHP), (iii) pressure-assisted densification techniques: room-temperature densification (RTD), cold sintering (CS), warm press (WP), and finally no-pressure assisted method called (iv) reactive hydrothermal liquid phase densification (rHLPD). Above named techniques are commonly assisted by an aqueous solution used as either reactant or transient liquid phase to assist densification. Starting from the background in traditional sintering processes, this review aims to explore in depth the existing literature about low temperature densification approaches along with their advantages & disadvantages, and probable application areas.Article Citation - WoS: 6Citation - Scopus: 6The Expansion Behavior of Slurries Containing Recycled Glass Powder Carboxymethyl Cellulose, Lime and Aluminum Powder(Elsevier, 2020) Zeren, Doğuş; Şentürk, Ufuk; Güden, MustafaThe rheology and foaming/expansion of the slurries of a waste/recycled glass powder with 50, 55 and 60 wt% of solid (glass powder) were experimentally investigated. The glass powder slurries were foamed using aluminum powder as foaming agent (0.75 wt%) and calcium hydroxide as activator (1 wt%). Sodium carboxymethyl cellulose (CMC) was added to the slurries as a binder with the amounts between 0 and 4 wt%. The expansions of the slurries were measured in-situ using a laser sensor and reported as percent volume expansion. The CMC-addition increased the viscosities of the slurries, particularly the fine size powder slurries. The slurries with the relatively low-viscosity exhibited lower initial expansion rates compared to the slurries with the relatively high-viscosity. The maximum expansions of the slurries increased from 300 to 350%, when the viscosity increased to 5 Pa s and reached a steady value around 400% between 5 and 50 Pa s. The expansions of the slurries could not be achieved above 50 Pa s since they became too thick to be foamed. The foam samples made from the slurries with 55 and 60 wt% of solid and sintered at 700 and 750 degrees C for 30 min had the average densities between 355 and 530 kg m(-3) and the average compressive strengths between 0.2 and 0.5 MPa. Increasing sintering time to 60 min at 750 degrees C increased the average compressive strength from 0.5 to 1.5 MPa for the foam samples made from the slurry with 60 wt% of solid. These proved that both sintering temperature and time were effective in increasing the compressive strengths of the foamed structures. The thermal conductivities of the sintered foam samples with the densities of 355 and 504 kg m(-3) were measured 0.042 and 0.057 W m(-1) K-1, respectively. (C) 2019 Elsevier Ltd. All rights reserved.