Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
6 results
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 35Citation - Scopus: 35Cvd Graphene/Sic Uv Photodetector With Enhanced Spectral Responsivity and Response Speed(Elsevier, 2023) Jehad, Ala K.; Fidan, Mehmet; Ünverdi, Özhan; Çelebi, CemA self-powered, high-performance graphene/Silicon Carbide (G/4H-SiC) ultraviolet Schottky junction photodetector has been fabricated, and the effect of using monolayer and bilayer graphene on the device performance parameters was investigated. P-type graphene sheets were grown by the chemical vapor deposition (CVD) method, while 4H-SiC material consists of an epilayer structure of n-/n+ on bulk n-SiC. Two photodetector devices have been studied, one with monolayer graphene (MLG) and the other with bilayer graphene (BLG). The proposed photodetector structure reveals the highest spectral responsivity known of a G/4H-SiC UV photodetector so far. Electronic and optoelectronic characterizations were done under an ultraviolet wavelength range from 240 to 350 nm. The results show two spectral responsivity maxima (Rmax) at 285 nm and 300 nm wavelengths. Exhibiting two maxima in spectral responsivity and detectivity is caused by the constructive and destructive interference effects of multiple reflections at the SiC epilayer's interfaces. The photodetector devices exhibit high spectral responsivity (R ? 0.09 AW?1), maximum detectivity (D* ? 2.9 × 1012 Jones), and minimum noise equivalent power (NEP ? 0.17 pWHz-1/2) in both devices. Using bilayer graphene instead of monolayer showed no significant change in both the photogenerated current and the spectral responsivity due to the higher absorption coefficient of bilayer graphene, however, it exhibited a significant improvement in the response speed. The response speed was found to increase by 50 % when bilayer graphene was used as a hole collecting electrode in the G/4H-SiC junction. This is because bilayer graphene creates a narrower depletion layer and higher electric field, which promotes efficient charge separation and recombination. © 2023 Elsevier B.V.Article Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.Article Citation - WoS: 9Citation - Scopus: 9Polymer-derived ceramic molten metal filters(Springer, 2022) Dizdar, Kerem Can; Kulkarni, Apoorv; Dışpınar, Derya; Soraru, Gian Domenico; Ahmetoğlu, Çekdar Vakıf; Semerci, TuğçeThis paper reports the synthesis and the performance of polymer-derived ceramic filters for molten metal filtration. Two different filter types were studied: foam filters produced from flexible polyurethane (PU) foams and additive manufacturing (AM) filters produced from thermoplastic polyurethane (TPU) cellular structure, and the results from all filter types were compared with that of the commercially used SiC foam filters. In both cases, the urethane-based polymeric template was impregnated with the preceramic solution, followed by pyrolysis. The produced ceramic components were then used to filter a molten Al alloy (A357), and the resulting Al samples were characterized for their mechanical properties. When filters were used, more reproducible and reliable mechanical properties were achieved compared to the samples obtained without any filtration. Among the different filters tested, the foam filters demonstrated better performance in comparison with the AM ceramic filters due probably to the three-dimensional interconnected porosity compared with the unidirectional cellular structure of the AM ceramic filters.Article Citation - WoS: 1Citation - Scopus: 2Electron Field Emission From Sic Nanopillars Produced by Using Nanosphere Lithography(AVS Science and Technology Society, 2017) Yeşilpınar, Damla; Çelebi, CemField emitter arrays of silicon carbide based nanopillars with high emitter density were fabricated by using a combination of nanosphere lithography and inductively coupled plasma reactive ion etching techniques. The electron field emission characteristics of the produced nanopillars with two different aspect ratios and geometries were investigated, and the obtained results were compared with each other. The authors found that unlike the samples containing low aspect ratio SiC nanopillars with blunt tip apex, the samples comprising high aspect ratio nanopillars with sharp tip apex generate greater emission currents under lower electric fields. The nanopillars with sharp tip apex produced field emission currents up to 240 μA/cm2 under 17.4 V/μm applied electric field, while the nanopillars with blunt tip apex produced an emission current of 70 μA/cm2. The electric fields required to obtain 10 μA/cm2 current density are found to be 9.1 and 7.2 V/μm for the nanopillars with blunt and sharp tip apex, respectively. Time dependent stability measurements yielded stable electron emission without any abrupt change in the respective current levels of both samples.Article Citation - WoS: 14Citation - Scopus: 16Microstructure and Mechanical Properties of A357/Sic Nanocomposites Fabricated by Ultrasonic Cavitation-Based Dispersion of Ball-Milled Nanoparticles(SAGE Publications Inc., 2017) Kandemir, SinanIn this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.Article Citation - WoS: 17Citation - Scopus: 26Thixoforming of A356/Sic and A356/Tib2 Nanocomposites Fabricated by a Combination of Green Compact Nanoparticle Incorporation and Ultrasonic Treatment of the Melted Compact(Springer Verlag, 2014) Kandemir, Sinan; Atkinson, Helen V.; Weston, David P.; Hainsworth, Sarah V.Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles.