Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
8 results
Search Results
Now showing 1 - 8 of 8
Article Repair and Strengthening of Fire Damaged Concrete Cylinders Using FRP Confinement: Tests and Analytical Modelling(Elsevier Science inc, 2025) Demir, Ugur; Ilki, AlperThis study examines the effects of fiber-reinforced polymer (FRP) repair and strengthening on the axial stress-strain behavior of concrete columns after exposure to realistic fires. A total of 30 plain concrete cylinders, each measuring 150 x 300 mm, were cast for this investigation. Of these, three specimens were kept as reference at ambient temperature, while the remaining were exposed to ISO-834 standard fire for durations of 30, 60 or 90 min, with nine specimens in each duration group. After natural cooling, the heated specimens were categorized into three groups: i) three were left unconfined, ii) three were repaired and strengthened using two layers of carbon FRP sheets, and iii) three were repaired and strengthened with four layers of carbon FRP sheets. This study employs realistic ISO 834 fire scenarios and investigates CFRP confinement with up to four layers, addressing high confinement demands beyond current literature. The results showed that transverse confinement provided by carbon FRP sheets significantly improved axial strength and deformability for all specimens, while it did not fully restore the axial stiffness achieved before fire exposure. The effectiveness of FRP confinement increased with longer fire exposure durations. Additionally, two analytical models proposed previously for predicting the axial strength and ultimate strain of FRP confined fire-damaged concrete were evaluated in terms of their accuracy. The accuracy of the predictions was reduced with an increase in exposure temperatures for both models. Therefore, a new model is proposed within the scope of study, which shows good agreement with the novel test results.Article Citation - WoS: 2Citation - Scopus: 2A Comprehensive Study on the Effectiveness of the Stress and Damage Model Parameters in Predicting the Compression Fracture Behavior of Selective Laser Melted AlSi10Mg BCC Lattices(Elsevier B.V., 2025) Guden, Mustafa; Erten, Hacer Irem; Gorguluarslan, Recep M.; Gulletutan, Umut Can; Dagkolu, Akin; Gokdag, Istemihan; Namazov, SubhanThe Johnson and Cook (JC) stress and damage model parameters determined from the machined bulk cylindrical specimens and as-built struts through tension and compression tests were used to model quasi-static compression behavior of selective laser melt-fabricated AlSi10Mg alloy lattices. The lattices had the same cell size (10 mm) and strut diameter (1 mm), but different number of cells (2 x 2 x 2, 10 x 10 x 2 and 5 x 5 x 5) and geometries (sandwich and cubic). Four different sets of JC damage model parameters (brittle and ductile notch-insensitive and compression and tension notch-sensitive) were further implemented in the lattice compression numerical models. The brittle damage model parameters and smaller mesh sizes resulted in cracking the face-sheet corner strut nodes before the occurrence of a bending-dominated initial peak stress. The notch-sensitive damage model parameters exhibited no bent-strut fracture in the middle layers of the lattices and increased the crack initiation strains as compared with the notch-insensitive damage model parameters. Despite significant variations in the initial peak stresses of the tested 2 x 2 x 2 and 10 x 10 x 2 lattices, the implication of the strut micro-tension stress model together with the compression notch-sensitive damage model parameters using 0.25 mm mesh size conservatively approximated the experimental deformation stresses while the machined bulk specimen tensionstress model over predicted the experimental stresses. On the other side, the strut stress model with 0.15 mm mesh size accurately predicted the experimental diagonal shear/fracture mode of struts with a slightly higher numerical initial peak stress. The compression tests on the strut specimens extracted from the as-built lattices yielded similar stress model parameters with the micro-tension tests. The differences between the initial peak stresses of the investigated sandwich and cubic lattices were further explained by the differences in the lattice boundary conditions.Article Citation - WoS: 8Citation - Scopus: 8A Review of the Experimental and Numerical Studies on the Compression Behavior of the Additively Produced Metallic Lattice Structures at High and Low Strain Rates(KeAi Communications Co., 2025) Bin Riaz, Muhammad Arslan; Guden, MustafaRecent advances in additive manufacturing have enabled the construction of metallic lattice structures with tailored mechanical and functional properties. One potential application of metallic lattice structures is in the impact load mitigation where an external kinetic energy is absorbed by the deformation/ crushing of lattice cells. This has motivated a growing number of experimental and numerical studies, recently, on the crushing behavior of additively produced lattice structures. The present study overviews the dynamic and quasi-static crushing behavior of additively produced Ti64, 316L, and AlSiMg alloy lattice structures. The first part of the study summarizes the main features of two most commonly used additive processing techniques for lattice structures, namely selective-laser-melt (SLM) and electrobeam-melt (EBM), along with a description of commonly observed process induced defects. In the second part, the deformation and strain rate sensitivities of the selected alloy lattices are outlined together with the most widely used dynamic test methods, followed by a part on the observed microstructures of the SLM and EBM-processed Ti64, 316L and AlSiMg alloys. Finally, the experimental and numerical studies on the quasi-static and dynamic compression behavior of the additively processed Ti6 4, 316L, and AlSiMg alloy lattices are reviewed. The results of the experimental and numerical studies of the dynamic properties of various types of lattices, including graded, non-uniform strut size, hollow, non-uniform cell size, and bio-inspired, were tabulated together with the used dynamic testing methods. The dynamic tests have been noted to be mostly conducted in compression Split Hopkinson Pressure Bar (SHPB) or Taylor-and direct-impact tests using the SHPB set-up, in all of which relatively small-size test specimens were tested. The test specimen size effect on the compression behavior of the lattices was further emphasized. It has also been shown that the lattices of Ti6 4 and AlSiMg alloys are relatively brittle as compared with the lattices of 316L alloy. Finally, the challenges associated with modelling lattice structures were explained and the micro tension tests and multi-scale modeling techniques combining microstructural characteristics with macroscopic lattice dynamics were recommended to improve the accuracy of the numerical simulations of the dynamic compression deformations of metallic lattice structures. (c) 2025 China Ordnance Society. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).Article Citation - Scopus: 7How Do the Influent Cod/Nitrogen and Internal Recirculation Ratios Affect the Oxidation Ditch Type Pre-Anoxic Landfill Leachate Treatment?(Academic Press, 2021) Çakirgöz,M.; Bayrakdar,A.; Çalli,B.A design-based dynamic simulation tool was developed to evaluate the effects of altered operation conditions on the performance of a landfill leachate treating pre-anoxic oxidation ditch folowed by external ultra filtration and nano filtration membranesby using the actual influent data and operational constants collected for 18 months. In the summer of 2017, the MBR suffered from reduced membrane fluxes due to deterioration of activated sludge flocs after the failure of flow booster providing the internal circulation and decreasing influent C/N ratio. Although two external pumps were activated in place of the broken flow booster, the required internal recirculation ratio (IR) predicted by the simulation could not be provided. It was concluded that due to low IR, the activated sludge retaining longer in the anoxic tank lost its floc integrity and caused decreased membrane fluxes. Simulation findings also showed that if the COD/N ratio drops below 4.8, no matter how high the IR is, it is unlikely to achieve a NOx-N concentration below 30 mg/l in the effluent. On the other hand, contrary to expectations, both the actual and estimated nitrification efficiencies were very high due to the moderately high temperature (>20 °C) and DO (2–3 mg/l) values in the aerobic basin. © 2020 Elsevier LtdArticle Citation - WoS: 54Citation - Scopus: 59Orientation Dependent Tensile Properties of a Selective-Laser 316l Stainless Steel(Elsevier, 2021) Güden, Mustafa; Yavaş, Hakan; Tanrıkulu, Ahmet Alptuğ; Taşdemirci, Alper; Akın, Barış; Enser, Samed; Karakuş, Ayberk; Arslan Hamat, BurcuThe effect of specimen inclination angle with respect to building direction on the tensile properties of a selective laser melt 316L alloy was investigated. Tensile test specimens were fabricated with the angles between 0 degrees to 90 degrees at 15 degrees intervals using a rotation scanning. In addition, 316L alloy test specimens were generated in the ANSYS 2020R1 additive module and tensile tested in LS-DYNA in order to determine the effect of residual stresses on the tensile strengths. The microscopic analysis revealed a strong < 110 > fiber texture orientation along the building direction (the loading axis of 0 degrees inclined specimens) and a weak 111 texture or nearly random distribution of directions in the normal to the building direction (tensile loading axis of 90 degrees inclined specimens). The yield and tensile strength increased and ductility decreased with increasing inclination angle. The strength variation with the inclination angle was shown well-fitted with the Tsai-Hill failure criterion. Although, the used numerical models indicated an inclination-dependent residual stress, the difference in the residual stresses was much lower than the difference in the strengths between 0 degrees and 90 degrees inclined specimens. Predictions showed a lower twinning stress in 0 degrees inclined specimens due to < 110 > fiber texture orientation in the tensile axis. The fiber texture resulted in extensive twinning; hence, higher ductility and tension-compression asymmetry in 0 degrees inclined specimens. Based on these results, the variations in the strength and ductility of tested SLM-316L specimens with the inclination angle was ascribed to the variations in the angle between the fiber texture orientation and loading axis.Article Citation - WoS: 19Citation - Scopus: 21Dynamic Crushing Behavior of a Multilayer Thin-Walled Aluminum Corrugated Core: the Effect of Velocity and Imperfection(Elsevier Ltd., 2018) Sarıyaka, Mustafa; Taşdemirci, Alper; Güden, MustafaThe crushing behavior of a multilayer 1050 H14 aluminum corrugated core was investigated both experimentally and numerically (LS-Dyna) using the perfect and imperfect models between 0.0048 and 90 m s−1. The dynamic compression and direct impact tests were performed in a compression type and a modified Split Hopkinson Pressure Bar set-up, respectively. The investigated fully imperfect model of the corrugated core sample represented the homogenous distribution of imperfection, while the two-layer imperfect model the localized imperfection. The corrugated core experimentally deformed by a quasi-static homogenous mode between 0.0048 and 22 m s−1, a transition mode between 22 and 60 m s−1 and a shock mode at 90 m s−1. Numerical results have shown that the stress-time profile and the layer crushing mode of the homogeneous and transition mode were well predicted by the two-layer imperfect model, while the stress-time profile and the layer crushing mode were well approximated by the fully imperfect model. The fully imperfect model resulted in complete sequential layer crushing at 75 and 90 m s−1, respectively. The imperfect layers in the shock mode only affected the distal end stresses, while all models implemented resulted in similar impact end stresses. The distal end initial crushing stress increased with increasing velocity until about 22 m s−1; thereafter, it saturated at ~2 MPa, which was ascribed to the micro inertial effect. Both the stress-time and velocity-time history of the rigid-perfectly-plastic-locking model and the critical velocity for the shock deformation were well predicted when a dynamic plateau stress determined from the distal end stresses in the shock mode was used in the calculations.Article Citation - WoS: 24Citation - Scopus: 23Graphene Oxide Bionanocomposite Coatings With High Oxygen Barrier Properties(MDPI Multidisciplinary Digital Publishing Institute, 2016) Uysal Ünalan, İlke; Boyacı, Derya; Ghaani, Masoud; Trabattoni, Silvia; Farris, StefanoIn this work, we present the development of bionanocomposite coatings on poly(ethylene terephthalate) (PET) with outstanding oxygen barrier properties. Pullulan and graphene oxide (GO) were used as main polymer phase and nanobuilding block (NBB), respectively. The oxygen barrier performance was investigated at different filler volume fractions (φ) and as a function of different relative humidity (RH) values. Noticeably, the impermeable nature of GO was reflected under dry conditions, in which an oxygen transmission rate (OTR, mL m-2 24 h-1) value below the detection limit of the instrument (0.01 mL m-2 24 h-1) was recorded, even for ' as low as 0.0004. A dramatic increase of the OTR values occurred in humid conditions, such that the barrier performance was totally lost at 90% RH (the OTR of coated PET films was equal to the OTR of bare PET films). Modelling of the experimental OTR data by Cussler’s model suggested that the spatial ordering of GO sheets within the main pullulan phase was perturbed because of RH fluctuations. In spite of the presence of the filler, all the formulations allowed the obtainment of final materials with haze values below 3%, the only exception being the formulation with the highest loading of GO (φ 0.03). The mechanisms underlying the experimental observations are discussed.Article Citation - WoS: 40Citation - Scopus: 53Models for Prediction of Daily Mean Indoor Temperature and Relative Humidity: Education Building in Izmir, Turkey(SAGE Publications Inc., 2012) Özbalta, Türkan Göksal; Sezer, Alper; Yıldız, YusufIn this research, several models were developed to forecast the daily mean indoor temperature (IT) and relative humidity values in an education building in Izmir, Turkey. The city is located at a hot-humid climatic region. In order to forecast the IT and internal relative humidity (IRH) parameters in the building, a number of artificial neural networks (ANN) models were trained and tested with a dataset including outdoor climatic conditions, day of year and indoor thermal comfort parameters. The indoor thermal comfort parameters, namely, IT and IRH values between 6 June and 21 September 2009 were collected via HOBO data logger. Fraction of variance (R2) and root-mean squared error values calculated by the use of the outputs of different ANN architectures were compared. Moreover, several multiple regression models were developed to question their performance in comparison with those of ANNs. The results showed that an ANN model trained with inconsiderable amount of data was successful in the prediction of IT and IRH parameters in education buildings. It should be emphasized that this model can be benefited in the prediction of indoor thermal comfort conditions, energy requirements, and heating, ventilating and air conditioning system size. © The Author(s), 2011. Reprints and permissions: