Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
11 results
Search Results
Now showing 1 - 10 of 11
Article Citation - WoS: 8Citation - Scopus: 9Development of Plant-Based Biopolymer Coatings for 3d Cell Culture: Boron-Silica Quince Seed Mucilage Nanocomposites(Royal Society of Chemistry, 2023) Yılmaz, Hilal Deniz; Cengiz, Uğur; Derkuş, Burak; Arslan, Yavuz EmreSpheroid formation with spontaneous aggregation has captured interest in most cell culture studies due to its easy set-up and more reliable results. However, the economic and technical costs of the advanced systems and commercial ultra-low adhesive platforms have pushed researchers into pursuing alternatives. Nowadays, polymeric coatings, including poly-hydroxyethyl methacrylate and agar/agarose, are the commonly used polymers for non-adhesive plate fabrication, yet the costs and working solvent or heat-dependent preparation procedures maintain the need for the development of novel biomaterials. Here, we propose a greener and more economical approach for producing non-adherent surfaces and spheroid formation. For this, a plant waste-based biopolymer from quince fruit (Cydonia oblonga Miller, from Rosaceae family) seeds and boron-silica precursors were introduced. The unique water-holding capacity of quince seed mucilage (Q) was enriched with silanol and borate groups to form bioactive and hydrophilic nanocomposite overlays for spheroid studies. Moreover, 3D gel plates from the nanocomposite material were fabricated and tested in vitro as a proof-of-concept. The surface properties of coatings and the biochemical and mechanical properties of the nanocomposite materials were evaluated in-depth with techniques, and extra hydrophilic coatings were obtained. Three different cell lines were cultured on these nanocomposite surfaces, and spheroid formation with increased cellular viability was recorded on day 3 with a >200 & mu;m spheroid size. Overall, Q-based nanocomposites are believed to be a fantastic alternative for non-adherent surface fabrication due to their low-cost, easy operation, and intrinsic hydration layer forming capacity with biocompatible nature in vitro.Article Citation - WoS: 16Citation - Scopus: 13Energy storage performance of nitrogen-doped reduced graphene oxide/co-doped polyaniline nanocomposites(Springer, 2022) Altınışık, Hasan; Getiren, Bengü; Çıplak, Zafer; Soysal, Furkan; Yıldız, NurayThe design and exploration of carbon-based electrode materials have become highly significant for developing supercapacitor technology, which has attracted considerable attention in energy storage systems. Here, nitrogen-doped reduced graphene oxide (N-rGO) – Polyaniline (PANI) nanocomposites were synthesized by a facile two-step method in which in situ polymerization of aniline monomer was performed on hydrothermally synthesized N-rGO nanosheets in DBSA and H2SO4 medium for co-doping of PANI chains. The effects of various acid concentrations (DBSA:H2SO4 0.5 − 0.25:1 n/n) and N-rGO:aniline ratios (N-rGO:aniline 1:4–10 m/m) used in the preparation of the electrode material on the capacitive properties were investigated. It is found that the co-doped N-rGO-PANI nanocomposites exhibit a high specific capacitance of 346.3 F g− 1 at 1 A g− 1, remarkable rate capacity (99.9%, 1–10 A g− 1) and excellent cycle stability at 5 A g− 1 (81.3%, 5000 cycles) in a two-electrode system. As a result, constructing co-doped PANI chains and N-doped rGO provided a viable and simple way to improve the capacitive performances of supercapacitors.Article Citation - WoS: 10Citation - Scopus: 9Recyclability of Cspbbr3 Quantum Dot Glass Nanocomposites for Their Long-Standing Use in White Leds(2022) Vahedigharehchopogh, Naji; Erol, Erdinç; Kıbrıslı, Orhan; Genç, Aziz; Çelikbilek Ersundu, Miray; Ersundu, Ali ErçinThe embedding of CsPbBr3 perovskite quantum dots (PQDs) in an inorganic glass matrix not only protects them against chemical, thermal, and photodegradation but also provides an effective strategy to isolate toxic elements such as Pb from the environment for a long period of time. Herein, the recyclability of glass is another important feature that contributes to environmental sustainability. Hence, effective and efficient recycling technologies are needed for the widespread use of PQD glass nanocomposites (GNCs) in many commercial applications. However, studies on the recyclability of CsPbBr3 PQD GNCs have not been conducted so far. Therefore, in this work, we investigate the structural, thermal, optical, and photoluminescence properties of recycled CsPbBr3 PQD GNCs to assess their suitability as long-standing and reusable luminescent materials. For this purpose, the recyclability of GNCs is checked by three repeated melt-quenching and subsequent heat-treatment processes. Although the color emission properties of GNCs under the same heat-treatment conditions show a slight variation after each recycling step, PQD GNCs almost retain their PLQY even after the last recycling step. Ultimately, a prototype white light-emitting diode is constructed by coupling recycled PQD GNCs and a commercial red phosphor on top of a blue LED chip showing high-performance with CIE color coordinates of x = 0.3228, y = 0.3470 and a CCT value of 5920 K. The findings of this work reveal that the recyclability of PQD GNCs holds great promise for a more sustainable technology.Article Citation - WoS: 34Citation - Scopus: 36Effects of Organo-Modified Clay Addition and Temperature on the Water Vapor Barrier Properties of Polyhydroxy Butyrate Homo and Copolymer Nanocomposite Films for Packaging Applications(Springer Verlag, 2018) Akın, Okan; Tıhmınlıoğlu, FundaPolymer nanocomposites, based on bacterial biodegradable thermoplastic polyester, poly(hydroxy-butyrate) (PHB), poly(hydroxyl-butyrate-co-hydroxy-valerate) (PHBHV), and commercial organo-modified montmorillonite (OMMT-Cloisite 10A) were prepared by solution casting method. This work aims to investigate the effect of Cloisite 10A type clay addition on the water vapour permeability properties of PHB/OMMT, and PHBHV/OMMT nanobiocomposite films. Temperature dependence of water vapor permeabilities of the films were also evaluated at various temperatures, and semi empirical permeability models were used to predict the permeability of polymer systems as a function of clay concentration and aspect ratio of nanoplates. Moreover, thermal, optical, and mechanical properties of the composites were examined by using varieties of techniques including differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), scanning electron microscope (SEM), and thin-film X-ray diffractometer (TF-XRD) respectively. Test results indicated that addition of highly intergallery swollen Cloisite 10A to the PHB/PHBHV, reduced the water vapor permeability up to 41 and 25% compared to native PHB and PHBHV films, respectively. Regarding the all mechanical properties measured, the maximum improvement was achieved for 3 wt% clay loaded samples for both PHB and PHBHV polymer composites. An increase of about 152 and 73% in tensile strength and of 77 and 18% in strain at break was achieved for PHB and PHBHV polymers, respectively. As a result of X-ray diffraction analysis, exfoliated structure was achieved at low clay loaded sample (1% w/w), however at higher concentration (3% w/w) the structure found as intercalated. Therefore, it is an evident that enhancement of characteristic properties highly depend on the dispersion level of clay particles in polymer matrix. The results obtained in this study show the feasibility of improvement of the properties of PHB based polymers with incorporation of nanoclay.Article Citation - WoS: 19Citation - Scopus: 20Transparent Pullulan/Mica Nanocomposite Coatings With Outstanding Oxygen Barrier Properties(MDPI Multidisciplinary Digital Publishing Institute, 2017) Uysal Ünalan, İlke; Boyacı, Derya; Trabattoni, Silvia; Tavazzi, Silvia; Farris, StefanoThis study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α), at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt %, which is φ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, however, this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase, because of RH fluctuations. This was confirmed by modelling of the experimental oxygen transmission rate (OTR) data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction, compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%. The only exception to this was represented by the formulation with the highest loading of mica (1.5 wt %, which is φ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.Article Citation - WoS: 59Citation - Scopus: 64Interfacial Thermal Resistance Between the Graphene-Coated Copper and Liquid Water(Elsevier Ltd., 2016) Pham, An T.; Barışık, Murat; Kim, BohungThe thermal coupling at water-solid interfaces is a key factor in controlling thermal resistance and the performance of nanoscale devices. This is especially important across the recently engineered nano-composite structures composed of a graphene-coated-metal surface. In this paper, a series of molecular dynamics simulations were conducted to investigate Kapitza length at the interface of liquid water and nano-composite surfaces of graphene-coated-Cu(1 1 1). We found that Kapitza length gradually increased and converged to the value measured on pure graphite surface with the increase of the number of graphene layers inserted on the Cu surface. Different than the earlier hypothesis on the "transparency of graphene," the Kapitza length at the interface of mono-layer graphene coated Cu and water was found to be 2.5 times larger than the value of bare Cu surface. This drastic change of thermal resistance with the additional of a single graphene is validated by the surface energy calculations indicating that the mono-layer graphene allows only ∼18% van der Waals energy of underneath Cu to transmit. We introduced an "overall interaction strength" value for the nano-composites based the quantitative contribution of pair interaction potentials of each material with water into the total surface energy in each case. Similar to earlier studies, results revealed that Kapitza length shows exponentially variation as a function of the estimated interaction strength of the nano-composite surfaces. The effect of Cu/graphene coupling on thermal behavior between the nano-composite with water was characterized. The Kapitza length was found to decrease significantly with increased Cu/graphene strength in the case of weak coupling, while this behavior becomes negligible with strong coupling of Cu and graphene.Article Citation - WoS: 33Citation - Scopus: 33Folic Acid Modified Clay/Polymer Nanocomposites for Selective Cell Adhesion(Royal Society of Chemistry, 2014) Barlas, Fırat Barış; Ağ Şeleci, Didem; Özkan, Melek; Demir, Bilal; Şeleci, Muharrem; Aydın, Muhammed; Taşdelen, M. A.; Zareie, Hadi M.; Timur, Suna; Özçelik, Serdar; Yağcı, YusufA folic acid (FA) modified poly(epsilon-caprolactone)/clay nanocomposite (PCL/MMT-(CH2CH2OH)2-FA) resulting in selective cell adhesion and proliferation was synthesized and characterized as a cell culture and biosensing platform. For this purpose, first the FA modified clay (MMT-(CH2CH2OH)2-FA) was prepared by treating the organo-modified clay, Cloisite 30B [MMT-(CH2CH 2OH)2] with FA in chloroform at 60°C. Subsequent ring opening polymerization of ε-caprolactone in the presence of tin octoate (Sn(Oct)2) using MMT-(CH2CH2OH)2-FA at 110°C resulted in the formation of MMT-(CH2CH 2OH)2-FA with an exfoliated clay structure. The structures of intermediates and the final nanocomposite were investigated in detail by FT-IR spectral analysis and DSC, TGA, XRD, SEM and AFM measurements. The combination of FA, PCL and clay provides a simple and versatile route to surfaces that allows controlled and selective cell adhesion and proliferation. FA receptor-positive HeLa and negative A549 cells were used to prove the selectivity of the modified surfaces. Both microscopy and electrochemical sensing techniques were applied to show the differences in cell adherence on the modified and pristine clay platforms. This approach is expected to be adapted into various bio-applications such as 'cell culture on chip', biosensors and design of tools for targeted diagnosis or therapy.Article Citation - WoS: 91Citation - Scopus: 113Rheological and Dynamic-Mechanical Behavior of Carbon Nanotube/Vinyl Ester-Polyester Suspensions and Their Nanocomposites(Elsevier Ltd., 2007) Seyhan, Abdullah Tuğrul; Gojny, F. H.; Tanoğlu, Metin; Schulte, K.Rheological properties of vinyl ester-polyester resin suspensions containing various amounts (0.05, 0.1 and 0.3 wt.%) of multi walled carbon nanotubes (MWCNT) with and without amine functional groups (-NH2) were investigated by utilization of oscillatory rheometer with parallel plate geometry. Dispersion of corresponding carbon nanotubes within the resin blend was accomplished employing high shear mixing technique (3-roll milling). Based on the dynamic viscoelastic measurements, it was observed that at 0.3 wt.% of CNT loadings, storage modulus (G′) values of suspensions containing MWCNTs and MWCNT-NH2 exhibited frequency-independent pseudo solid like behavior especially at lower frequencies. Moreover, the loss modulus (G″) values of the resin suspensions with respect to frequency were observed to increase with an increase in contents of CNTs within the resin blend. In addition, steady shear viscosity measurements implied that at each given loading rate, the resin suspensions demonstrated shear thinning behavior regardless of amine functional groups, while the neat resin blend was almost the Newtonian fluid. Furthermore, dynamic mechanical behavior of the nanocomposites achieved by polymerizing the resin blend suspensions with MWCNTs and MWCNT-NH2 was investigated through dynamic mechanical thermal analyzer (DMTA). It was revealed that storage modulus (E′) and the loss modulus (E″) values of the resulting nanocomposites increased with regard to carbon nanotubes incorporated into the resin blend. In addition, at each given loading rate, nanocomposites containing MWCNT-NH2 possessed larger loss and storage modulus values as well as higher glass transition temperatures (Tg) as compared to those with MWCNTs. These findings were attributed to evidences for contribution of amine functional groups to chemical interactions at the interface between CNTs and the resin blend matrix. Transmission electron microscopy (TEM) studies performed on the cured resin samples approved that the dispersion state of carbon nanotubes with and without amine functional groups within the matrix resin blend was adequate. This implies that 3-roll milling process described herein is very appropriate technique for blending of carbon nanotubes with a liquid thermoset resin to manufacture nanocomposites with enhanced final properties.Conference Object Citation - WoS: 39Citation - Scopus: 48Temperature Dependence of Electrical Conductivity in Double-Wall and Multi-Wall Carbon Nanotube/Polyester Nanocomposites(Springer Verlag, 2007) Şimşek, Yılmaz; Özyüzer, Lütfi; Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, KarlThe aim of this study is to investigate temperature dependence of electrical conductivity of carbon nanotube (CNT)/polyester nanocomposites from room temperature to 77 K using four-point probe test method. To produce nanocomposites, various types and amounts of CNTs (0.1, 0.3 and 0.5 wt.%) were dispersed via 3-roll mill technique within a specially formulized resin blend of thermoset polyesters. CNTs used in the study include multi walled carbon nanotubes (MWCNT) and double-walled carbon nanotubes (DWCNT) with and without amine functional groups (-NH2). It was observed that the incorporation of carbon nanotubes into resin blend yields electrically percolating networks and electrical conductivity of the resulting nanocomposites increases with increasing amount of nanotubes. However, nanocomposites containing amino functionalized carbon nanotubes exhibit relatively lower electrical conductivity compared to those with non-functionalized carbon nanotubes. To get better interpretation of the mechanism leading to conductive network via CNTs with and without amine functional groups, the experimental results were fitted to fluctuation-induced tunneling through the barriers between the metallic regions model. It was found that the results are in good agreement with prediction of proposed model.Article Citation - WoS: 12Citation - Scopus: 14Anomalous Transmittance of Polystyrene-Ceria Nanocomposites at High Particle Loadings†(Royal Society of Chemistry, 2013) Parlak, Onur; Demir, Mustafa MuammerOptical nanocomposites based on transparent polymers and nanosized pigment particles have usually been produced at low particle concentrations due to the undesirable optical scattering of the pigment particles. However, the contribution of the particles to many physical properties is realized at high concentrations. In this study, nanocomposites were prepared with transparent polystyrene (PS) and organophilic CeO2 nanoparticles using various compositions in which the particle content was up to 95 wt%. The particles, capped by 3-methacryloxypropyltrimethoxysilane (MPS), were dispersed into PS and the transmittance of the spin-coated composite films was examined over the UV-visible region. When the particle concentration was <20 wt%, the transmittance of the films showed a first-order exponential decay as the Rayleigh scattering theory proposes. However, a positive deviation was observed from the decay function for higher particle contents. The improvement in transmittance may be a consequence of interference in the multiple scattering of light by the quasi-ordered internal microstructure that gradually develops as the particle concentration increases.