Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
5 results
Search Results
Now showing 1 - 5 of 5
Article Citation - WoS: 1Citation - Scopus: 1Effect of Drying Method on Selected Physical and Functional Properties of Powdered Black Soldier Fly Larvae(Mdpi, 2025) Bogusz, Radoslaw; Nowacka, Malgorzata; Gondek, Ewa; Delman, Murat; Szulc, KarolinaThis research aimed to assay the impact of convective drying (CD) or infrared-convective (IR-CD) drying methods on the physical and techno-functional properties, FTIR spectra, and mathematical modeling of adsorption kinetics of black soldier fly larvae powders. By using convective drying, insect powder exhibited higher water content and water activity but lower hygroscopicity than powder dried with the infrared-convective method. After drying with the convective method, the powder exhibited a significantly lower loose and tapped bulk density and oil holding capacity (OHC). Furthermore, this powder was lighter and more yellow. The FTIR spectrum of the CD-dried powder showed lower absorption at key wavenumbers for the protein (1625 and 1350-1200 cm-1), indicating lower denaturation and less ability to bind water and water vapor. The mathematical modeling of the water vapor adsorption kinetics of insect powders via the second Fick's law for transient diffusion showed that this equation is suitable for adjusting the experimental data based on the high coefficient of determination (0.997-0.999) and the low root mean square (2.50-3.34%). This study revealed that the drying method influences insect powder properties, and the IR-CD method seems better in terms of obtaining better techno-functional properties.Article Citation - WoS: 2Citation - Scopus: 2Morphology of Sodium Salt of Calf Thymus Dna on Mica, Alumina, and Silica Surfaces: Effect of Solvent and Drying Method(Taylor and Francis Ltd., 2017) Yetgin, Senem; Balköse, DevrimInvestigation of morphology of deoxyribonucleotide triphosphate (DNA) dried on different surfaces by atomic force microscopy (AFM) is important in DNA research that is focused on subjects of condensation for gene therapy, sizing, DNA mapping, and cancer examination. The solvent, the surface type, and the method of drying effect the morphology of DNA on solid surfaces. Ethanol and water were used as solvents, flat mica, silica, and alumina surfaces were used as the substrates in the present study. Different methods such as ambient air-drying, N2-forced flow regime drying, and freeze-drying have been applied to droplets of DNA solutions in water or ethanol on the substrates. Forced flow drying regime causes nonlinear DNA attachment on the surface and self-assembly. DNA vertical distance on mica surface was found to be 6 and 1.4 nm for DNA dried in ambient air from ethanol and water solutions, respectively. It was 1.6 nm for N2 flow drying of aqueous DNA solution on mica surface. It was 4.6, 4.6, and 1.99 nm for ambient, N2 flow, and freeze-dried aqueous DNA on alumina surfaces, respectively. Aqueous solution of DNA dried under N2 flow on silica surface had 0.8 nm vertical distance. The smallest standard deviation of 0.05 nm was observed for DNA dried under N2 flow on alumina surface.Article Citation - WoS: 27Citation - Scopus: 28An Exergetic Performance Assessment of Three Different Food Driers(SAGE Publications Inc., 2010) Hepbaşlı, Arif; Erbay, Zafer; Çolak, Neslihan; Hancıoğlu, Ebru; İçier, FilizIn this study, plum slices were dried in three different driers (tray, fluid bed, and heat pump (HP) driers). Drying experiments were carried out at an air temperature range of 45-55 °C with an air velocity of 1.5 m/s. The performance of the driers along with their main components was evaluated and compared by using the exergy analysis method. The most important component for improving the system efficiency was determined to be the fan-heater combination for both the tray and fluid bed driers, and the motor-compressor assembly for the HP drier. The exergy loss and flow diagram (the so-called Grassmann diagram) of the driers was also presented to give quantitative information regarding the proportion of the exergy input dissipated in the various system components. Effects of the drying air temperature on the performance of the drying process were discussed. The highest exergetic efficiency values were obtained to range from 72.72 to 75.66 per cent for the HP drier, followed by the tray and fluid bed driers varying between 37.94 and 39.46 per cent, and between 22.83 and 24.07 per cent, respectively.Article Citation - WoS: 71Citation - Scopus: 77A Comparative Study on Exergetic Performance Assessment for Drying of Broccoli Florets in Three Different Drying Systems(Taylor and Francis Ltd., 2010) İçier, Filiz; Çolak, Neslihan; Erbay, Zafer; Hancıoğlu Kuzgunkaya, Ebru; Hepbaşlı, ArifThis article deals with the exergy analysis and evaluation of broccoli in three different drying systems. The effects of drying air temperature on the exergy destruction, exergy efficiency, and exergetic improvement potential of the drying process were investigated. The exergy destruction rate for the drying chamber increased with the rise in the drying air temperature at 1.5 m/s, both in the tray and the heat pump dryer. The highest exergy efficiency value was obtained as 90.86% in the fluid bed dryer in comparison to the other two drying systems and the improvement potential rate was the highest in the heat pump dryer during drying of broccoli at the drying air temperature of 45°C and the drying air velocity of 1.0 m/s. © 2010 Taylor & Francis Group, LLC.Article Citation - WoS: 10Citation - Scopus: 10Multi-Zone Drying Schemes for Lowering the Residual Solvent Content During Multi-Component Drying of Semicrystalline Polymers(Taylor and Francis Ltd., 2007) Wong, Sim-Siong; Alsoy Altınkaya, Sacide; Mallapragada, Surya K.The development of a glassy skin in multicomponent semicrystalline polymer systems limits the diffusion of solvents out of the system and increases residual solvent levels. Based on the results of a mathematical model that we had previously developed, we have proposed a multi-zone drying scheme aimed at lowering the residual solvent levels by taking into account the effect of interactions between the various solvents as predicted by the model. This article focuses on the application of this model to develop optimal drying schemes and to verify the effectiveness of these predictions using experimental techniques. The mathematical model developed previously to study the diffusion of multiple solvents and changes in the crystallinity of semicrystalline polymer systems during drying incorporates many features including Vrentas-Duda diffusion theory, solvent-induced crystallization kinetics, as well as glass transition effects and skinning of the film. The multi-zone drying system was developed by varying the drying temperature in each zone as well as changing the partial pressure of individual solvents during the drying process. The effectiveness of the multi-zone drying schemes predicted by the model was validated experimentally using thermogravimetric methods. The polymer-solvent system chosen was a poly(vinyl alcohol)-water-methanol system. Our experimental data suggested that the multi-zone drying schemes were superior to a single-zone drying system through direct comparison. Further examination of the mathematical model yielded individual solvent profiles and these data reaffirmed our conclusions that a multi-zone drying scheme has the ability to reduce the effect of solvent trapping and thus lower the overall residual solvent content.